Change message to make allow distinguishing between error while
getting page info for disk configuration and page layout
verification.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
STM32L4plus mcu has SDMMC internal DMA which works without any
configuration and it's handled by SDMMC HAL driver. This commit adds
option to enable it and use it.
Signed-off-by: Petr Hlineny <development@hlineny.cz>
MMC was using SDMMC kconfigs to build disk driver.
This is incorrect, MMC and SDMMC should not be sharing
Kconfigs. Split the drivers/disk/Kconfig.sdmmc into
drivers/disk/Kconfig.mmc and drivers/disk/Kconfig.sdmmc.
Also update disk tests to account for new MMC Kconfigs.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Similarly to what was done in USB or RNG drivers, configure 48MHz domain
clock using device tree.
By default a freq clock check is enabled.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This is important for applications which are chain-loaded by a broken
bootloader which doesn't reset the peripheral before handing over control.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
Add stub code for SDIO support, capable of verifying card responds to CMD5.
This commit also changes the architecture of the SDIO probe step to make
adding new protocol support more streamlined, and enable compiling out
support for undesired protocols.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The HSI48 is enabled by clock control driver.
It is no more done by each driver that requires this clock
However when using rng or sdmmc or bluetooth/ipm or usb,
the HSI48 clock must be present in the DTS.
Add a warning for this particular check but keep the deprecated
HSI48 clock enable : keeping for legacy but to remove later.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Fail with error if any of flashdisk partition assumptions are not met:
* uniform page size through the whole partition
* flashdisk starts at page boundary
* flashdisk ends at page boundary
Read-only flashdisks are not subject to above conditions because the
cache buffer is not used for read-only flashdisks.
The checks can be disabled via Kconfig option to save code space.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Force cache-size to 0 and treat flashdisk as read-only when backing
partition has read-only flag set. This allows users to save RAM when the
application does not write to the flashdisk, e.g. when a predefined FAT
filesystem is used.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Cache written data to avoid rewriting same flash page multiple times
when writing subsequent flash pages. The cache is used for reads to
account for reading not yet committed (i.e. dirty) page data. Speeding
up reads is not intention of this patch and therefore the read path
does not modify cache state.
Fixes: #30212
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Set default of DISK_DRIVER_SDMMC Kconfig based on the devicetree.
This should avoid having to set the kconfig at the board level
in order to use sdmmc.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Remove all obsolete DISK_FLASH* Kconfig options.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Use devicetree to obtain information for all zephyr flash disks.
Co-authored-by: Johann Fischer <johann.fischer@nordicsemi.no>
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Change automated searching for files using "IRQ_CONNECT()" API not
including <zephyr/irq.h>.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Fix the scope of some variables in various STM32 drivers including:
- SDMMC
- DMA
- OSPI/QSPI Flash
- Interrupt controller
The variables are set static instead of global and const if appropriate.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
* Enable hardware flow control on Kconfig
* Enable HSI48 clock on sdmmc_stm32 driver
Signed-off-by: Gerson Fernando Budke <gerson.budke@ossystems.com.br>
For some stm32 devices, the SDMMC clock selection is HSI 48MHz
by default (reset value). It must be enabled before acccessing
the peripheral.
The ErrorCode is reported when Init fails.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Many device pointers are initialized at compile and never changed. This
means that the device pointer can be constified (immutable).
Automated using:
```
perl -i -pe 's/const struct device \*(?!const)(.*)= DEVICE/const struct
device *const $1= DEVICE/g' **/*.c
```
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This fixes underrun issues when hardware flow control can't be used.
Only tested on STM32F4.
Signed-off-by: John Kjellberg <kjellberg.john@gmail.com>
...
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
remove existing SDMMC SPI driver, since it is replaced by the SPI mode
SD host controller driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
all in tree SOCs with the USDHC peripheral have now been converted to
use the new SD host controller USDHC driver, so remove legacy NXP disk
USDHC driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Even if not used DMA HAL is required in F4 SD HAL driver. Just
as for L4/F7 series that have been added before.
Add it for this specific serie.
Signed-off-by: John Kjellberg <kjellberg.john@gmail.com>
Enable pinctrl driver for usdhc. USDHC driver uses custom pinctrl states
for fast, slow, and medium signal frequencies, as well as pin pull for
SD detection.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The PINCTRL_DT_(INST_)DEFINE macros already defined the trailing ;,
making its usage inconsistent with other macros such as
DEVICE_DT_DEFINE.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add checks for the upper boundary in access_read/access_write
instead of the homeopathic ASSERTS.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
USDHC driver did not pass disk test (failed during multiple writes). Add
logic to wait for the SD card to be idle before reading new data, so
that the test will pass. Also, add logic to reject OOB reads and writes
to the disk.
Fixes#39942
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
RT11xx USDHC lacks some watermarking features that RT10xx SOCs include.
Place #ifdef guards around these features.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Even if not used DMA HAL is required in L4/F7 SD HAL driver.
Add them for these specific series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
During SDMMC card init, HW_FC is disabled by default, overwriting
driver configuration.
To avoid this, move HW FC configuration after card init.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add a Kconfig symbol to enable use of SDMMC hardware flow control.
In specific cases, this feature could help to avoid FIFO ovderrun
and underrun errors.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The function usdhc_board_access_init was returning a non-zero
value as the variable "ret" is also used to store the GPIO
level for card-detect.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
