Updated uart_rx_enable() and uart_tx() to use timeout given
in microseconds. Previously argument was given in milliseconds.
However, there are cases when milliseconds granularity is not
enough and can significantly reduce a throughput, e.g. 1ms is
100 bytes at 1Mb.
Updated 4 drivers which implement asynchronous API. Updated
places where API was used.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
It enables the usart6 to run the testcase with a DMA
tests/drivers/uart/uart_async_api. DMA2 (of type V1)
is configured on channel 5 (request) streams 7 & 2.
USART Tx and Rx PG14 - PG9 pins (14 & 16 of CN10)
are connected to PASS the test.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This sets the dts of DMA for using pn the uart 2 i.
The stm32h723 has a DMAMUX and request are 44 and 43 for usart2
The Tx&Rx pins PD5 and PD6 of the usart2 are connected
on the nucleo_h723zg board to pass the test
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add configuration for testing the usart3 through the dma1
on the nucleo_l152re target.This test requires the Tx pin
to be connected to the RX pin on the board.
Pin definition is added for this usart instance.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit configures usart3 to use dma in uart_async_api test
on nucleo_l552ze_q platform.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
This commit configures usart3 to use dma in uart_async_api test
on stm32l562e_dk platform. Short pin2(PC10) & pin 3 (PC11) of usart3
in CN4 connector on stm32l562e_dk platform.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
Adds nucleo_g071rb board to the uart_async_api test.
Therefore additionally add usart1 in board definitions.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This sets the dts of dma for using the uart asynch api.
The stm32l475 has a dmamux with request 2 for Tx/Rx usart4
The Tx&Rx pins (PA0, PA1) of the usart4 are connected
on the disco_l475_iot1 board to pass the test.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit adds the asynchronous UART API testing support on the
nucleo_l4r5zi board.
The usart3 module is used as the secondary loop-back UART, which is
required to run this test.
Signed-off-by: Shlomi Vaknin <shlomi.39sd@gmail.com>
After finish transmitting some bytes might be in the
peripheral receive register, since the transmition
is still happening after reception disabled.
This patch ensures that the peripheral has no
bytes in its internal state.
Signed-off-by: Shlomi Vaknin <shlomi.39sd@gmail.com>
Extend the test_single_read test case to catch RX_RDY events that are
not expected to appear.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The cached device pointer must be placed in memory that allows user
mode invocation of the test functions to access it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The device pointer is now provided to the callback, there is no need to
call uart_callback_set() with the device being set a user data.
Fixes#26923
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This commit adds the asynchronous UART API testing support on the SAM
E54 Xplained Pro board.
The SERCOM1 module is used as the secondary loop-back UART, which is
required to run this test.
Note that no external UART loop-back connection is necessary to run
this test, because the SERCOM1 UART TX and RX pads are configured to be
internally connected; it is, however, still necessary to configure the
pinmux because the module pads are not connected until the pinmux is
configured.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Convert DT_UART_{0,1}_NAME to DT_NODELABEL() references as the cases are
board specific and this allows us to remove DT_UART_{0,1}_NAME defines
in dts_fixup.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Substitute integral constants where call sites passed named constants
that have timeout values as arguments to parameters that expect
millisecond durations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This commit adds the asynchronous UART API testing support on the SAM
R21 Xplained Pro board.
The SERCOM3 module is used as the secondary loop-back UART, which is
required to run this test.
Note that no external UART loop-back connection is necessary to run
this test, because the SERCOM3 UART TX and RX pads are configured to be
internally connected; it is, however, still necessary to configure the
pinmux because the module pads are not connected until the pinmux is
configured.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the asynchronous UART API testing support on the SAM
D21 Xplained Pro board.
The SERCOM1 module is used as the secondary loop-back UART, which is
required to run this test.
Note that no external UART loop-back connection is necessary to run
this test, because the SERCOM1 UART TX and RX pads are configured to be
internally connected.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
We rename the nRF91 Dev Kit board target (nrf9160_pca10090)
to nrf9160dk_nrf9160. We update all associated references
in the supportive documentation and all nRF9160-related
cofigurations and overlay files in the samples and tests
in the tree.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The nRF52840 DK board target, so far known as nrf52840_pca10056,
is renamed to nrf52840dk_nrf52840.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Check for proper driver behaviour if timeout for uart_rx_enable or
uart_tx is set to K_FOREVER.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Use the int_literal_to_timeout Coccinelle script to convert literal
integer arguments for kernel API timeout parameters to the standard
timeout value representations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
move uart.h to drivers/uart.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add an explict test for the length of the receive event when
doing incremental receives. This was not tested anywhere in the
normal code path (only implicitly in the abort, which wasn't
exercised on the only current implementation, nrfx). So add an
explicit check for it during the chained reads, so that the
test can catch the case where multiple receive events do not set
the length correctly on events past the first.
Tested on nrf52840_pca10056.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
This reverts commit d09b91f5. I was incorrect in my interpretation
of the async API: the number of bytes received is relative
to the previous event, so it does "reset" between calls.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
During the write abort test, a second write is started then quickly
aborted. This means that the number of bytes sent is relative
to that second write. So when comparing it against the number
of bytes received which is NOT reset, the first (completed)
send of five bytes has to be accounted for. The current
nrfx implementations abort quick enough that no bytes are reported
sent, so this wasn't currently being exercised (i.e. the short
circuit of zero bytes sent was taken).
Tested on nrf52840_pca10056.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Added tests for async UART API and test configuration for
nrf52840_pca10056 board.
For tests to work, RX and TX pins have to be connected together
and second UART is needed to output results to console.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
