Remove old configurations of boards that do not support networking
natively and very custom and difficult to test.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Start to monitor Connected and Disconnect events and then start
and stop the echo service according to system connectivity status.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The size_t type is either compatible with an int on 32-bit target, or
a long on 64-bit targets. It could even be a long even on some 32-bit
targets. Let's use the z qualifier in the printf format to be compatible
with whatever flavor in use.
In case of pointers, let's just use %p with pointers directly and
avoid casts altogether.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Delete IPSP sample file, this source file is not included in any build
files. The service contains no valuable logic other than advertising
with the IPSP service in the advertising data.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Move the HID over GATT service into the sample that demonstrates it.
This avoids long build paths
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Move the Current Time service into the sample that demonstrates it.
This avoids long build paths
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Move the health thermometer service into the sample folder that
demonstrates it. This avoids long build paths
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This commit moves the BLE GATT heart rate service from
samples/bluetooth/gatt to subsys/bluetooth/services and adds a Kconfig
entry to enable and configure the service.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This commit moves the BLE GATT Battery service
from /samples/bluetooth/gatt to /subsys/bluetooth/services and
adds a Kconfig entry to enable and configure the service;
when enabled, it will register itself automatically.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The name disk_access_sdhc.c is ambiguous,
actually this driver depends on SPI,
rename this file.
In addition, move the generic sdhc stuff from C file
to head file for other sdhc drivers to use.
1) disk_access_sdhc.c->disk_access_spi_sdhc.c.
2) create .h and move sdhc specifications from .c to .h.
Signed-off-by: Jun Yang <jun.yang@nxp.com>
Flags in alarm configuration structure will allow further extention
without breaking API. Initially, existing absolute flag was added
as the only flag.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Converts all net samples that enable the mcr20a 802.15.4 driver to use
the frdm_cr20a shield instead of hardcoding configs for the frdm_k64f
base board. This makes it possible to build mcr20a samples for other
base boards with compatible arduino headers.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
If a sample wants to use the Zephyr implementation of mbedtls, it
enables CONFIG_MBEDTLS and sets any needed Zephyr-specific mbedtls
options.
Currently, the LwM2M subsystem selects MBEDTLS automatically when
LWM2M_DTLS_SUPPORT is enabled. Let's remove this and let the
LwM2M client sample enable mbedtls and it's options.
This mimics the behavior of several other network-related samples
and removes conflicts when selecting alternate implementations of
MBEDTLS.
Fixes: https://github.com/zephyrproject-rtos/zephyr/issues/17399
Signed-off-by: Michael Scott <mike@foundries.io>
Provide two basic example samples to test the x-nucleo-iks01a3 shield:
- Standard (Mode 1)
- SensorHub (Mode 2)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Update to documentation for the sample audio application running
on Sue Creek S1000 board from Intel.
Added section on how to control the audio application on target
from a Linux host and updated the console output section
accordingly.
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Add python script and associated configuration YAML file
to control audio sample application running on
Intel Sue Creek S1000 from a Linux host.
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Add tuning driver, audio block processing threads,
background processing thread and USB transport driver
to the cmake build in audio sample app.
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Add a status check to start/stop audio in order to start
audio only if it's not already running and to stop audio
only if it is running.
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Add processing threads for small/large audio blocks
in audio sample app for Intel® Sue Creek S1000 board
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Add USB transport driver to control the sample application
from a host connected to Intel® Sue Creek S1000 board
via an USB interface.
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
If user has set CONFIG_NET_CONTEXT_TIMESTAMP then enable
network packet throughput collection for UDP packets.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The current CMSIS v2 implementation is clearly assuming that timeout
arguments being passed to e.g. osDelay() are in units of Zephyr ticks,
not milliseconds as specified by ARM or (inconsistently) assumed by
our test code.
Most tests work with the ~100 Hz default tick rate, but they tend to
fail on precision issues at higher tick rates. Force the CMSIS v2
applications to be 1000 Hz for now as a workaround, and detect the
mismatch as a build failure.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
When tickless is available, all existing devices can handle much
higher timing precision than 10ms. A 10kHz default seems acceptable
without introducing too much range limitation (rollover for a signed
time delta will happen at 2.5 days). Leave the 100 Hz default in
place for ticked configurations, as those are going to be special
purpose usages where the user probably actually cares about interrupt
rate.
Note that the defaulting logic interacts with an obscure trick:
setting the tick rate to zero would indicate "no clock exists" to the
configuration (some platforms use this to drop code from the build).
But now that becomes a kconfig cycle, so to break it we expose
CONFIG_SYS_CLOCK_EXISTS as an app-defined tunable and not a derived
value from the tick rate. Only one test actually did this.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Tick rate is becoming a platform tunable in the tickless world. Some
apps were setting it due to requirements of drivers or subsystems (or
sometimes for reasons that don't make much sense), but the dependency
goes the other way around now: board/soc/arch level code is
responsible for setting tick rates that work with their devices.
A few tests still use hard-configured tick rates, as they have
baked-in assumptions (like e.g. "a tick will be longer than a
millisecond") that need to be addressed first.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Recursive make should be invoked as $(MAKE) and not "make" for reasons
documented at
https://www.gnu.org/software/make/manual/html_node/MAKE-Variable.html
$(MAKE) is what CMake puts in all the CMakeFiles/Makefile2 it generates,
it doesn't use "make" either.
Issue found thanks to the following warning:
build.log:make[4]: warning: jobserver unavailable: using -j1.
Add '+' to parent make rule.
If CMake is invoked with -GNinja or other then fall back on "make" as
before and pray that it's available.
Fast reproduction with:
make -j2 -C build clean mylib_project VERBOSE=1
Build directories have been compared before/after this change and
there's zero difference except the generated
mylib_project.dir/build.make file (and the warning above) when using
make.
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Adding Health Thermometer Service sample. Refer to Health Thermometer
Profile Specification for detailed information about the Health
Thermometer Profile.
Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
We use the following commands to rename any
LED._GPIO_{CONTROLLER,PIN,FLAGS} to
DT_ALIAS_LED._GPIOS_{CONTROLLER,PIN,FLAGS}
git grep -l LED._GPIO_CONTROLLER | xargs sed -i 's/LED\(.\)_GPIO_CONTROLLER/DT_ALIAS_LED\1_GPIOS_CONTROLLER/g'
git grep -l LED._GPIO_PIN | xargs sed -i 's/LED\(.\)_GPIO_PIN/DT_ALIAS_LED\1_GPIOS_PIN/g'
git grep -l LED._GPIO_FLAGS | xargs sed -i 's/LED\(.\)_GPIO_FLAGS/DT_ALIAS_LED\1_GPIOS_FLAGS/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Previously we always used the board identifier (via CONFIG_BOARD) as
identifier, however this causes troubles in case of tests with multiple
boards of the same kind on the same server. The device_id addresses that
problem nicely if enabled and supported by the architecture.
Signed-off-by: Daniel Egger <daniel@eggers-club.de>
Print IP address for added or removed IP address. This helps
to understand what IP address is being removed or added.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add support for the FXOS8700CQ present on the NXP TWR-KE18F
development board. The FXOS8700CQ IRQ lines are not connected by
default on the TWR-KE18F, so only polling (no trigger) is supported.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add support for polling the sensor values of the FXOS8700 device when
no trigger (interrupt) is enabled.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Introduce a separate buffer pool for events which the HCI driver
considers discardable. Examples of such events could be e.g.
Advertising Reports. The benefit of having such a pool means that the
if there is a heavy inflow of such events it will not cause the
allocation for other critical events to block and may even eliminate
deadlocks in some cases.
Also update all mesh samples not to specify explicit RX buffer counts
anymore. Instead, create appropriate defaults in Kconfig so that we
only need to override this in the app for cases like the bbc:microbit
with limited memory.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We use the following commands to rename any
SW._GPIO_{CONTROLLER,PIN,FLAGS} to
DT_ALIAS_SW._GPIOS_{CONTROLLER,PIN,FLAGS}
git grep -l SW._GPIO_CONTROLLER | xargs sed -i 's/SW\(.\)_GPIO_CONTROLLER/DT_ALIAS_SW\1_GPIOS_CONTROLLER/g'
git grep -l SW._GPIO_PIN | xargs sed -i 's/SW\(.\)_GPIO_PIN/DT_ALIAS_SW\1_GPIOS_PIN/g'
git grep -l SW._GPIO_FLAGS | xargs sed -i 's/SW\(.\)_GPIO_FLAGS/DT_ALIAS_SW\1_GPIOS_FLAGS/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We use the following commands to rename any _PWM_{CONTROLLER,CHANNEL}
to *_PWMS_{CONTROLLER,CHANNEL}
Used the following commands to make these changes:
git grep -l '[A-Z_0-9]*_PWM_CONTROLLER' | xargs sed -i 's/\([A-Z_0-9]*\)_PWM_CONTROLLER/DT_ALIAS_\1_PWMS_CONTROLLER/g'
git grep -l '[A-Z_0-9]*_PWM_CHANNEL' | xargs sed -i 's/\([A-Z_0-9]*\)_PWM_CHANNEL/DT_ALIAS_\1_PWMS_CHANNEL/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
move misc/reboot.h to power/reboot.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/stack.h to debug/stack.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
