When there'is no phy at the address both registers will return
0xFFFF, giving a phy address of UINT32_MAX, not 0x00FFFFFF.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
The 62833 added a regression at SAM ethernet drivers which always fail
to initialize due to a wrong switch case implementation and without
review from maintainer. This add more information and fix the issue.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Simplify the driver header implementation, so that there are not
structs and unions different per each situtaion, and make just one
function for the enet module drivers to call on each other. Also,
capitalize existing enums.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
The NET_L2_ETHERNET_MGMT configuration option is required to allow
setting MAC address or PLCA parameters with the LAN865x driver.
To avoid mistakes with per-board configuration files - it has been moved
to Kconfig and automatically selected when the driver support is enabled.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Handle the situation when OA TC6 compliant device signals to the host
that its configuration is lost - i.e. the SYNC bit in the footer is
cleared.
In this (unlikely happen) situation the device is reset and reconfigured.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
As part of IRQ service routine, there is at least one data transmission
performed between OA TC6 compliant device and HOST uC.
As this transmission can happen when there is no valid data to be read
(and its only purpose is to deassert the interrupt) the DV bit in footer
may be cleared. As this situation is expected with this approach - the
LOG level can be safely lowered from error to debug.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
According to the OPEN Alliance 10Base-T1x standard (point 7.7), it is
mandatory to read at least single data chunk (no matter if received data
is valid or not) to deassert the interrupt in the LAN865x (then the tc6
structure fields are also updated from the footer).
Current approach with reading OA_BUFSTS register was providing the
required information (RCA and TXC), but could cause transmission "stalls"
as this operation (i.e. control, not data transmission) is not causing
deassertion of the interrupt IRQ_N line from OA TC6 compliant device.
With this patch - the transmission is always performed at least once, so
interrupt is always deasserted.
As the functionality of oa_tc6_update_buf_info() - i.e reading value of
RCA and TXC - has been replaced with extracting data from footer, this
function can be safely removed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
In case of boards where REF_CLK signal is not connected
to the GPIO0 by default add the possibility to use
the optional GPIO16/GPIO17 as a REF CLK source.
Signed-off-by: Bartosz Bilas <bartosz.bilas@hotmail.com>
NSEC_PER_SEC is an unsigned literal which will promote variable increment
to unsigned for the comparison operation, thus returning -EINVAL for
negative increment values.
For positive increment, -NSEC_PER_SEC becomes a large unsigned value
which will also return -EINVAL.
Fix by casting NSEC_PER_SEC to an int.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
This commit provides support for changing PLCA parameters stored in
lan865x_config_plca structure.
After values are updated, the LAN865x needs to be reset and then
configured with new values.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The LAN865x device after HW reset supports only the non-protected control
transmission mode. When it is reset alone - without resetting already
configured HOST system - one must assure that in HOST's OA TC6 driver
the protection SPI transmission support is disabled.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The ctx->reset member of struct lan865x_data shall be cleared each time
one wants to reset the LAN8651 device.
Before this change this value was only initialized in the lan865x_init().
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This change allows modification of the PLCA configuration in the lan865x
driver.
Values in this structure can be set via device tree as well as modified
by the user program.
Without this change the latter use case would not be possible as the
struct lan865x_config structure is defined as read only and its data
is only provided by device tree.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add driver for NXP ENET which is a rework of the old
eth_mcux.c driver which had become unmaintainable due to
fundamental problems with the lack of PHY abstraction.
eth_mcux.c and the corresponding compatible nxp,kinetis-ethernet
will be deprecated and this new driver will be supported instead.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add Driver for KSZ8081 Ethernet PHY. The Generic MII Driver
is not sufficient to use for this PHY chip which has special
vendor implemented behaviors.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add a property to the ethernet controller binding
indicating what type of connection the MAC has with
the PHY device.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Adds the tja1103 enet phy for setting phy options on the mr_canhubk3.
Co-authored-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
The code to handle OA TC6 compliant device's status is generic and can
be moved to device agnostic driver (oa_tc6.c).
Moreover, the original code has been augmented with LOG_WRN() messages.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This change fixes semaphores' definition. To be more specific - the
limit was wrongly set to UINT_MAX. With those changes - the 'tx_rx_sem'
now assures that only one execution path (i.e. receiving or sending
data) is executed at a time.
Moreover, the change in 'int_sem' now assures that this semaphore limit,
when reached, is saturated.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit ensures that whole receive function (called from interrupt
handler) is protected by the RX/TX semaphore.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The oa_tc6_update_buf_info() function returns error code when read
(protected or not) of OA_BUFSTS has been detected.
In that situation - one shall re-start the interrupt thread handling
(and hence correctly re-read value of this register) than use old
(stalled) RCA(RBA) data to read chunks (which may result in lockup).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Current code sends extra, last chunk, when packet's size is a multiple
of chunk size (i.e. 64 bytes).
This patch fixes this issue by checking this corner case - i.e. if
the modulo division equals to zero.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The RCA and RBA fields in OA_BUFSTS register are stored with 8 bits each.
On the other hand, when one receives those values in footer, the value
is saturated to 5 bits due to 32 bit size constrain of the footer itself.
To avoid any mismatches - the values read from OA_BUFSTS are saturated
as well.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Zephyr's network stack has issues with network IP header split across
fragments.
To alleviate this problem, the frame would be now aligned to first byte
of the chunk. This would ensure that the header is stored at one network
buffer fragment (as we explicitly set its size to 64B).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The OA TC6 driver requires some bits manipulations in control registers.
Up till now - it has been implemented as an explicit set of read and write
registers' operations.
One good example would be the oa_tc6_set_protected_ctrl() implementation,
which used such scheme.
This patch brings dedicated function for this operation; oa_tc6_reg_rmw().
The aforementioned oa_tc6_set_protected_ctrl() function now uses it
internally.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add the missing dependency of the node status value
and enable the driver by default when they are met.
Signed-off-by: Bartosz Bilas <bartosz.bilas@hotmail.com>
This driver assumed the ivshmem-v2 output sections would be mapped
contiguously, which is no longer true.
Modify eth_ivshmem to treat each output section independently
Signed-off-by: Grant Ramsay <gramsay@enphaseenergy.com>
Regression failure introduced problem where driver code was not properly
wrapping code that only existed when compiled for IPv4/v6 applications.
Fixes#65549
Signed-off-by: David Leach <david.leach@nxp.com>
This moves the k_* memory management functions from sys/ into
kernel/ includes, as there are kernel public APIs. The z_*
functions are further separated into the kernel internal
header directory.
Also made a quick change to doxygen to group sys_mem_* into
the OS Memory Management group so they will appear in doc.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The SoC header already includes the necessary device headers for
all SoC variants supported.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Currently, the NXP S32 SoCs have three redundant Kconfig hidden
options to define the part number. To streamline this, we will
retain `CONFIG_SOC_PART_NUMBER` to store the part number as a
string and `CONFIG_SOC_PART_NUMBER_<part>` that can be selected
by the boards.
Furthermore, for drivers requiring conditional code compilation
based on the target SoC, they should utilize the series or SoC
config option as applicable, instead of the part number config.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
'native_posix_source_files' is used only when CONFIG_NATIVE_APPLICATION=y,
but it was set unconditionally regardless of this Kconfig option.
Set 'native_posix_source_files' under CONFIG_NATIVE_APPLICATION=y to narrow
scope of this variable.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
This patch set provides support for T1S ethernet device - LAN8651.
For SPI communication the implementation of Open Alliance TC6
specification is used.
The driver implementation focuses mostly on reducing memory footprint,
as the used SoC (STM32G491) for development has only 32 KiB RAM in total.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Those files provide generic functions to handle transmission between chip
conforming OA TC6 standard and Zephyr's network stack represented by
struct net_pkt.
The communication is performed via SPI and is focused on reduced memory
footprint (works with SOC equipped with 32 KiB of RAM) and robustness of
operation.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
There is no require to prevent building nxp s32 netc
shim driver if NET_TEST is set, so just remove this
unnecessary dependency
Fix#64944
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
One of the ARM architure files, defined since long ago
CONCAT having the exact same purpose as Zephyr's _CONCAT.
Unfortunately this header is included almost always
and the macro defined in all ARM based platforms,
which seems to have lead to many uses of this macro
instead of _CONCAT.
Fix it by using _CONCAT instead.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Modified files (yaml, dts, overlay, and c) which were using spi-cpol
and spi-cpha to be compatible with the new structure.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
Corrects set_config to allow MAC config
at runtime.
* Add missing device lock
* Use correct mac argument
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
The initialisation of the device data struct was giving a build error
when using the adi,adin1110 devicetree compatible.
Fixed to allow both adi,adin2111 and adi,adin1110 devices to
be defined.
Signed-off-by: Jason Murphy <jason.murphy@analog.com>
As the automatic start requires that the zephyr exe is run as
a root user, it is somewhat cumbersome to use. Remove the script
support and require that the zeth device is created beforehand
by the net-setup.sh script found in net-tools zephyr project.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
