This allows testing code that uses the UART interrupt-driven API and
UART asynchronous API.
Signed-off-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
Zephyr increments the gain until it reaches the maximum value and
then sets the registers to zero which is incorrect.
The values set in the DMIC config should be restored.
Signed-off-by: Fabiola Kwasowiec <fabiola.kwasowiec@intel.com>
Add `mdio_read_c45()`/`mdio_write_c45()` APIs for Clause 45 access
and remove the `protocol` MDIO binding property so that MDIO bus
controller can support more than one protocol.
A new MDIO header is introduced with generic opcodes, MMD and
registers addresses, to be used by MDIO and PHY drivers.
Existing MDIO drivers that support both Clause 22 and Clause 45
access are migrated to the new APIs.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Rename argument `devad` to `regad` to indicate this is the register
address in a given PHY device and to not be confused with the
Clause 45 device address within a port.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
When slave_address is 10 bits, data type should be
uint16_t instead of uint8_t,
like the data typeof data->slave_cfg->address.
https://github.com/zephyrproject-rtos/zephyr/issues/55987
Signed-off-by: Francois Ramu <francois.ramu@st.com>
On S32K344, the offset in memory map between each channel
is 0x4000 for most channels, but there is specific case is
between channel 11 and 12 which is 0x1D4000 instead. As a
consequence, 32 channels are divided to two parts: one
starts from channel 0 -> 11. The other is from channel 128
to 145. The channel gap is from 12 -> 127.
For user and data structures in shim driver, the channel's
value comes from 0 --> 31. Above constraint will be counted
when interact with the mcux sdk
Beside that, the DMAMUX register in this platform is very
specific, not in identical with DMAMUX channel, so shim
driver is updated to cover this case
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Add new dt binding for edma v3 that inherits whole dt
properties from current version. One more property is
added for SoCs that don't have separate error interrupt
id, use same id with channel interrupt
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
The current implementation iterates over all channels
even if only several channels share the same irq. This
introduces one more dt property to describe an offset
between two channels share the same interrupt id.
Beside that, the error interrupt must be put as last
element of "interrupt" dt property.
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
The dma-channels devicetree value - 1 = maximum valid channel
The dma-requests devicetree value - 1 = maximum valid request
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
A buffer overflow happens in send() when size is negative because
it is promoted to signed when used in memcpy.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Since the driver is passing the whole buffer, let's zero it to avoid
pass garbage in case of size != buffer's size.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
It is possible to happen a buffer overflow in ipm_send due the lack
of a checking for negative value.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Since the driver is passing the whole buffer, let's zero it to avoid
pass garbage in case of size != buffer's size.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
It is possible to happen a buffer overflow in ipm_send callback
due a wrong comparison between signed/unsigned types.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Replaces the previous approach to define bands via hardware capabilities
by the standard conforming concept of channel pages.
In the short term this allows us to correctly calculate the PHY specific
symbol rate and several parameters that directly depend from the symbol
rate and were previously not being correctly calculated for some of the
drivers whose channel pages could not be represented previously:
* We now support sub-nanosecond precision symbol rates for UWB. Rounding
errors are being minimized by switching from a divide-then-multiply
approach to a multiply-then-divide approach.
* UWB HRP: symbol rate depends on channel page specific preamble symbol
rate which again requires the pulse repetition value to be known
* Several MAC timings are being corrected based on the now correctly
calculated symbol rates, namely aTurnaroundTime, aUnitBackoffPeriod,
aBaseSuperframeDuration.
In the long term, this change unlocks such highly promising functional
areas as UWB ranging and SUN-PHY channel hopping in the SubG area (plus
of course any other PHY specific feature).
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Aligns the name of the return value variable with what is used elsewhere
in the driver and the subsystem for improved readability and
consistency.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Preparative change to introduce build-time configured channel pages.
This fixes the description of the driver's available PHYs and makes
channel page and channel range independent from runtime attributes.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
SPI API allows `spi_buf_set` structures with no buffers linked to them
(with `.buffers = NULL`). Correct the spi_nrfx_spis driver so that it
is able to deal with such structures.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Based on review of the similar charger driver API, it's been demonstrated
from the community that embedding a per value property type when fetching
properties. Separating off the property types from the property values
themselves also allow an array of property types to declared as static
const.
Break up fuel_gauge_property struct into a fuel_gauge_prop_val union and a
fuel_gauge_prop_t property type as inputs into fuel gauge API functions.
Signed-off-by: Aaron Massey <aaronmassey@google.com>
Based on review of the similar charger driver API, it's been demonstrated
from the community that embedding a per value status code when fetching
multiple properties isn't particularly wanted or needed. It was largely
considered not worth the additional maintenance to have the extra per
property error information.
Remove the status field from the fuel_gauge property value structs.
Signed-off-by: Aaron Massey <aaronmassey@google.com>
The fuel_gauge_set_prop() function prototype declares a function that sets
multiple fuel gauge properties at once. The naming suggests it ought to
fetch a singular property at a time. Moreso, some clients may just want to
set properties one at a time and may feel uncomfortable using a prototype
for fetching multiple properties when wanting to fetch them one at a time.
Modify fuel_gauge_set_prop() to fetch a single property and add
fuel_gauge_set_props() to support fetching multiple properties. Modify
existing tests/drivers/samples.
This is part of #61818 work.
Signed-off-by: Aaron Massey <aaronmassey@google.com>
The fuel_gauge_get_prop() function prototype declares a function that
retrieves multiple fuel gauge properties at once. The naming suggests it
ought to fetch a singular property at a time. Moreso, some clients may just
want to fetch properties one at a time and may feel uncomfortable using a
prototype for fetching multiple properties when wanting to fetch them one
at a time.
Modify fuel_gauge_get_prop() to fetch a single property and add
fuel_gauge_get_props() to support fetching multiple properties. Modify
existing tests/drivers/samples.
This is part of #61818 work.
Signed-off-by: Aaron Massey <aaronmassey@google.com>
When radio is set to promiscuous mode it is desirable to receive
invalid frames. This skip a few checks and allow an invalid and
non-standard frames be delivered for diagnose.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The i2c_ll_stm32_v2 driver requires manual timing configuration for
"fast mode plus" speed.
This adds an error message linking to the appropriate documentation.
Signed-off-by: Jonas Otto <jonas@jonasotto.com>
While recent browsers seem to transparently try to use https for
http://www.st.com/... URLs, they are effectively not working anymore, so use
https://www.st.com/... URLs instead.
curl http://www.st.com/en/evaluation-tools/nucleo-g070rb.html -m 5 -v
* Trying 104.89.117.48:80...
* Connected to www.st.com (104.89.117.48) port 80 (#0)
> GET /en/evaluation-tools/nucleo-g070rb.html HTTP/1.1
> Host: www.st.com
> User-Agent: curl/8.1.2
> Accept: */*
>
* Operation timed out after 5002 milliseconds with 0 bytes received
* Closing connection 0
curl: (28) Operation timed out after 5002 milliseconds with 0 bytes
received
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This commit does not introduce any functional change to the
codebase. Just removes certain redundant checks from
various CMakeLists.txt files in order to bring more coherence
in the codebase.
Signed-off-by: Jilay Pandya <jilay.pandya@zeiss.com>
Send a fw ready reply message as soon as possible.
This is usually used on host side which is waiting
for this message in order to establish the
communication with the remote processor - see
imx_dsp_rproc driver from Linux.
This can be enabled by IPM_IMX_FW_READY_REPLY config,
which is by default N.
Set CONFIG_IPM_IMX_FW_READY_REPLY as Y for
openamp_rsc_table sample, running on nxp_adsp_imx8m.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
NOCACHE_MEMORY depends on ARCH_HAS_NOCACHE_MEMORY_SUPPORT, so
don't try to select the symbol if not supported.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Refines the `system_mm.h` to include `zephyr/types.h` instead
of `zephyr/kernel.h` as that is all it needs.
Updated the includes of `mm_drv_ti_rat.c` accordingly.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Based on RM0456, each PLL in the STM32U5 has the
capability to work either in integer or fractional mode.
In this update, the fractional mode can be enabled
by setting the fracn value in the device tree.
Signed-off-by: Jatty Andriean <jandriea@outlook.com>
Split the read function into 2 versions (date and no date) since they
don't have common code.
It improves readability.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Add support for using the sub second registers. It allows reading and
setting alarm with the sub second tick resolution.
The RTC module is configured to get as high frequency as possible, which
equals the source clock (RTCCLK) divided by 2. To get such frequency,
the asynchronous prescaler is set to 1.
According to RM, setting the asynchronous prescaler to a high value
minimize consumption, so the change increase the power consumption.
Use a config to enable the sub second support.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
RTC drivers uses only seconds, so transition to microseconds is
necessary.
Change way of calculation tick<->time to avoid unnecessary
conversations.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Synchronize reading two separate registers. In some edge cases the read
registers could point different dates.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
The config values have been hardcoded as magic values. Introduce
universal calculation based on the DTS entries.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
This separates the DT device init macros into two: one for
UART accessed via IO port or MMIO, the other for PCIe UART.
All the conditions needed to setup the device structs are
getting complicated. Hopefully separating them would make
them easier to decode, and to avoid the conditions having
too many levels.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The old CONFIG_UART_NS16550_ACCESS_IOPORT has been used to
indicate whether to access the NS16550 UART via IO port
before device tree is used to describe hardware. Now we have
device tree, and we can specify whether a particular UART
needs to be accessed via IO port using property io-mapped.
Therefore, CONFIG_UART_NS16550_ACCESS_IOPORT is no longer
needed (and thus also CONFIG_UART_NS16550_SIMULT_ACCESS).
Remove these two kconfigs and modify code to use device tree
to figure out how to access the UART hardware.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Instead of PCIE0 and PCIE1, use no suffix for IO port/MMIO IRQ
configuration funct, and suffix PCIE for IRQ config on PCIE
bus.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Use CODE_CODE_1() instead of macro trampolines when
CONFIG_UART_NS16550_PARENT_INIT_LEVEL is enabled.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Using COND_CODE_1() is more intuitive when looking at the code,
instead of some macro trampoline magic.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This simplifies DLF and PCP enabling devicetree macros with
DT_ANY_INST_HAS_PROP_STATUS_OKAY() instead of the complicated
ones.
Also, this moves the macro to initialize struct elements into
the struct initializer itself. This makes it clearer on which
element is being initialized directly inside the struct
initializer instead of having to do mental macro trampoline
to find the correct macro.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
