The LPS22DF is an ultracompact, piezoresistive, absolute pressure sensor
that functions as a digital output barometer. The LPS22DF provides lower
power consumption, achieving lower pressure noise than its predecessor.
This driver is based on stmemsc HAL i/f v2.3
https://www.st.com/en/datasheet/lps22df.pdf
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The `int1-gpios` property is common for both spi and i2c
implementations of adxl372. Therefore move it to
`adi,adxl372-common.yaml`
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Add basic support for ams TSL2561 light sensor. Triggers, attributes
and manual integration time are currently not supported.
Signed-off-by: Gustavo Silva <gustavograzs@gmail.com>
Both the BQ27421 and BQ27427 have a few preset Chemistry profiles.
For the BQ27421 there exists three variants of the IC, and for the BQ27427,
it can be configured. The chemistry profile among other things includes the
taper voltage, which is used to detect charge termination.
This adds an optional `chemistry-id` config option to the driver. On the
BQ27421, it will confirm that the correct variant of the IC is mounted,
and on the BQ27427, it will configure it with the correct value.
Side note: The reference manual for the BQ27427
(https://www.ti.com/lit/ug/sluucd5/sluucd5.pdf) currently contains some
errors and inconsistencies regarding these registers. The table on page 7
appears to be correct.
Signed-off-by: Tobias Pisani <topisani@hamsterpoison.com>
Add in DT the possibility to configure both INT1 and INT2
pin. The driver will then assign one of the two (either 1
or 2, according to what value drdy_pin is set) to a gpio
for receiving drdy interrupts.
The other pin may be used in the future to receive event
interrupts.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
add basic sensor support for 3-axis accelerometer, currently
this driver support data acquisition and motion detection
features.
Signed-off-by: Karthikeyan Krishnasamy <karthikeyan@linumiz.com>
Add wakeup_duration support. (WAKE_DUR in WAKE_UP_DUR)
Value is configurable through DT per instance.
Signed-off-by: Adrian Wojak <adrian.wojak@outlook.com>
Specify only the bus corresponding to the current yaml file, as done in
the adi,adxl372-spi.yaml.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Introduce support for Texas Instruments TMAG5170
high-precision linear 3D Hall-effect SPI sensor.
This driver allows to configure measurements on
magnetic and temperature channels. It is also
possible to read rotation of the magnet.
Signed-off-by: Michal Morsisko <morsisko@gmail.com>
Adds initial support for hm330x dust sensor series. Allows to read PM1,
PM2.5 and PM10 concentrations in atmospheric environment. A further
update to the driver may add support for also reading "standard" CF1
concentrations by exposing of a custom sensor attribute or a Kconfig
option. Tested with Grove - Laser PM2.5 Sensor (HM3301) attached to a
Wio Terminal.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Moved the interrupt handling code from a bus-specific binding file to
the parent binding file. This modification ensures that interrupt
handling, which is inherently independent of the type of BUS used
(either i2c or spi), is located in the appropriate location within
the code.
Previously, this code was found in a bus-specific file, despite its
functionality being applicable to all buses. This change ensures a
more logical placement and will help to maintain coherence within the
codebase.
This change aligns with the existing implementation where the interrupt
handling code already operates independently of the BUS type.
Tested this on a nrf52840 with a bmi270 on spi bus with the sample from
zephyr/samples/sensor/bmi270 by adding an interrupt handler in main.c
which uses the bmi270_trigger.c implementation and verified this with
breakpoints and log output.
Added the irq-gpios to tests/drivers/build_all/sensor/i2c.dtsi and
tests/drivers/build_all/sensor/spi.dtsi and fixed whitespace formatting.
Fixes: #58843
Signed-off-by: Andreas Wiesinger <awiesing90@gmail.com>
Add `thr-sel` prop. to select the relevant threshold register for adc
comparator since there're two adc modules in npcx4 series.
Signed-off-by: Kate Yen <htyen@nuvoton.com>
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
The current-shunt calibration requires a factor of 4x if high-precision
mode is selected.
Signed-off-by: Eric Holmberg <eric.holmberg@northriversystems.co.nz>
Added configuration of termination current and trickle voltage
Added option to bypass low voltage charge inhibit
Added option to disable automatic recharge
Signed-off-by: Andy Sinclair <andy.sinclair@nordicsemi.no>
Added a driver for the DFRobot A01NYUB distance sensor. This sensor
sends its readings via UART at 9600 baud. This driver uses interrupts
to read the data from the sensor.
Signed-off-by: Oliver King <oliver.king@steadconnect.com>
This adds support for the bosch bmi085 and bmi088. This also includes
support for data sync mode.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
Changes rshunt-milliohms to rshunt-micro-ohms allowing for current
sensing of greater than 16.4A (1mOhm resistor). This is commonly
set to 100 uOhm for VMU/FMU boards/applications.
Co-authored-by: James Goppert <james.goppert@gmail.com>
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
Add driver for TCN75A temperature sensor. The following features are
supported:
- TCN75A oneshot mode, which allows single shot conversions with lower
power consumtion
- Resolution selection, up to 12 bit resolution (9 bit default)
- Triggering based on temperatue thresholds. If the TCN75A exits a set
threshold range, the application can be notified via a callback.
Signed-off-by: Daniel DeGrasse <daniel@degrasse.com>
