No need to mix super short version of names with other structures
having full name. Let's follow a more relevant naming where each and
every attribute name is self-documenting then. (such as s/id/apic_id
etc...)
Also make CONFIG_ACPI usable through IS_ENABLED by enclosing exposed
functions with ifdef CONFIG_ACPI.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
We need the same logic for each SOC, instead of copypasting
things just put this in a common file. This approach still
leaves the door open for custom memory layouts if desired.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This code had one purpose only, feed timing information into a test and
was not used by anything else. The custom trace points unfortunatly were
not accurate and this test was delivering informatin that conflicted
with other tests we have due to placement of such trace points in the
architecture and kernel code.
For such measurements we are planning to use the tracing functionality
in a special mode that would be used for metrics without polluting the
architecture and kernel code with additional tracing and timing code.
Furthermore, much of the assembly code used had issues.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
According to Intel 64 and IA-32 Architectures Software
Developer’s Manual, volume 3, chapter 8.2.5, LFENCE provides
a more efficient method of controlling memory ordering than
the CPUID instruction. So use LFENCE here, as all 64-bit
CPUs have LFENCE.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
It implements gdb remote protocol to talk with a host gdb during the
debug session. The implementation is divided in three layers:
1 - The top layer that is responsible for the gdb remote protocol.
2 - An architecture specific layer responsible to write/read registers,
set breakpoints, handle exceptions, ...
3 - A transport layer to be used to communicate with the host
The communication with GDB in the host is synchronous and the systems
stops execution waiting for instructions and return its execution after
a "continue" or "step" command. The protocol has an exception that is
when the host sends a packet to cause an interruption, usually triggered
by a Ctrl-C. This implementation ignores this instruction though.
This initial work supports only X86 using uart as backend.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The x86 paging code has been rewritten to support another paging mode
and non-identity virtual mappings.
- Paging code now uses an array of paging level characteristics and
walks tables using for loops. This is opposed to having different
functions for every paging level and lots of #ifdefs. The code is
now more concise and adding new paging modes should be trivial.
- We now support 32-bit, PAE, and IA-32e page tables.
- The page tables created by gen_mmu.py are now installed at early
boot. There are no longer separate "flat" page tables. These tables
are mutable at any time.
- The x86_mmu code now has a private header. Many definitions that did
not need to be in public scope have been moved out of mmustructs.h
and either placed in the C file or in the private header.
- Improvements to dumping page table information, with the physical
mapping and flags all shown
- arch_mem_map() implemented
- x86 userspace/memory domain code ported to use the new
infrastructure.
- add logic for physical -> virtual instruction pointer transition,
including cleaning up identity mappings after this takes place.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
These macros are used to validate that regions aren't
programmed that allow both writes and execution.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
These stacks are appropriate for threads that run purely in
supervisor mode, and also as stacks for interrupt and exception
handling.
Two new arch defines are introduced:
- ARCH_KERNEL_STACK_GUARD_SIZE
- ARCH_KERNEL_STACK_OBJ_ALIGN
New public declaration macros:
- K_KERNEL_STACK_RESERVED
- K_KERNEL_STACK_EXTERN
- K_KERNEL_STACK_DEFINE
- K_KERNEL_STACK_ARRAY_DEFINE
- K_KERNEL_STACK_MEMBER
- K_KERNEL_STACK_SIZEOF
If user mode is not enabled, K_KERNEL_STACK_* and K_THREAD_STACK_*
are equivalent.
Separately generated privilege elevation stacks are now declared
like kernel stacks, removing the need for K_PRIVILEGE_STACK_ALIGN.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This had been copy-pasted between linker scripts, create
a central header for it.
The linker scripts for xtensa and posix have very different
structure and have been left alone.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The core kernel computes the initial stack pointer
for a thread, properly aligning it and subtracting out
any random offsets or thread-local storage areas.
arch_new_thread() no longer needs to make any calculations,
an initial stack frame may be placed at the bounds of
the new 'stack_ptr' parameter passed in. This parameter
replaces 'stack_size'.
thread->stack_info is now set before arch_new_thread()
is invoked, z_new_thread_init() has been removed.
The values populated may need to be adjusted on arches
which carve-out MPU guard space from the actual stack
buffer.
thread->stack_info now has a new member 'delta' which
indicates any offset applied for TLS or random offset.
It's used so the calculations don't need to be repeated
if the thread later drops to user mode.
CONFIG_INIT_STACKS logic is now performed inside
z_setup_new_thread(), before arch_new_thread() is called.
thread->stack_info is now defined as the canonical
user-accessible area within the stack object, including
random offsets and TLS. It will never include any
carved-out memory for MPU guards and must be updated at
runtime if guards are removed.
Available stack space is now optimized. Some arches may
need to significantly round up the buffer size to account
for page-level granularity or MPU power-of-two requirements.
This space is now accounted for and used by virtue of
the Z_THREAD_STACK_SIZE_ADJUST() call in z_setup_new_thread.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The existing minimal ACPI implementation was enough to find the MADT
table for dumping CPU info. Enhance it with a slightly less minimal
implementation that can fetch any table, supports the ACPI 2.0 XSDT
directory (technically required on 64 bit systems so tables can live
>4G) and provides definitions for the MCFG table with the PCI
configuration pointers.
Note that there is no use case right now for high performance table
searching, so the "init" step has been removed and tables are probed
independently from scratch for each one requested (there are only
two).
Note also that the memory to which these tables point is not
understood by the Zephyr MMU configuration, so in long mode all ACPI
calls have to be done very early, before z_x86_paging_init() (or on a
build with the MMU initialization disabled).
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Previously, DTS specification of physical RAM bounds did not
correspond to the actual bounds of system RAM as the first
megabyte was being skipped.
There were reasons for this - the first 1MB on PC-like systems
is a no-man's-land of reserved memory regions, but we need DTS
to accurately capture physical memory bounds.
Instead, we introduce a config option which can apply an offset
to the beginning of physical memory, and apply this to the "RAM"
region defined in the linker scripts.
This also fixes a problem where an extra megabyte was being
added to the size of system RAM.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Remove Kconfig, linker script, and related bits associated with
CUSTOM_RODATA_LD, CUSTOM_RWDATA_LD, CUSTOM_SECTIONS_LD,
SOC_NOINIT_LD, SOC_RODATA_LD, and SOC_RWDATA_LD options that have been
deprecated since Zephyr 2.2.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Without this builds for qemu_x86 can't invoke k_cycle_get_32()
because z_timer_cycle_get_32() is installed with a mangled name.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This doesn't work as expected with kernel page table isolation
turned on, and fixing it would likely lose any latency benefits
that direct ISRs are supposed to provide.
For now, just prevent these macros from being defined if KPTI
is turned on, like other arches that do not implement this
feature.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The SoCs usually have devices that are accessed through MMIO.
This requires the corresponding regions to be marked readable
and writable in the MMU or else accesses will result in page
faults.
This adds a function which can be implemented in the SoC code to
specify those pages to be added to MMU.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
x86-32 thread objects require special alignment since they
contain a buffer that is passed to fxsave/fxrstor instructions.
This fell over if the dummy thread is created in a stack frame.
Implement a custom swap to main for x86 which still uses a
dummy thread, but in an unused part of the interrupt stack
with proper alignment.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This commit renames the x86 Kconfig `CONFIG_{EAGER,LAZY}_FP_SHARING`
symbol to `CONFIG_{EAGER,LAZY}_FPU_SHARING`, in order to align with the
recent `CONFIG_FP_SHARING` to `CONFIG_FPU_SHARING` renaming.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Rework x86 linker scripts to use DT_REG_ADDR/DT_REG_SIZE on
DT_CHOSEN(zephyr_sram) and DT_CHOSEN(zephyr_flash). As part of this
we remove the dts_fixup.h. Using DT_REG_SIZE means we don't have to
adjust the sizes by 1024.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace DT_PHYS_RAM_ADDR and DT_RAM_SIZE with DT_REG_ADDR/DT_REG_SIZE
for the DT_CHOSEN(zephyr_sram) node.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This operation is formally defined as rounding down a potential
stack pointer value to meet CPU and ABI requirments.
This was previously defined ad-hoc as STACK_ROUND_DOWN().
A new architecture constant ARCH_STACK_PTR_ALIGN is added.
Z_STACK_PTR_ALIGN() is defined in terms of it. This used to
be inconsistently specified as STACK_ALIGN or STACK_PTR_ALIGN;
in the latter case, STACK_ALIGN meant something else, typically
a required alignment for the base of a stack buffer.
STACK_ROUND_UP() only used in practice by Risc-V, delete
elsewhere.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The return value of the interrupt is never used, so remove the
functionality from the API. We ripple this change into the
ARCH_IRQ_CONNECT and ARCH_IRQ_DIRECT_CONNECT implementations. With
this change we can also remove the compound expression as that is
not needed anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The callee-saved registers have been separated out and will not
be saved/restored if exception debugging is shut off.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
In zephyr_linker_sources().
This is done since the point of the location is to place things at given
offsets. This can only be done consistenly if the linker code is placed
into the _first_ section.
All uses of TEXT_START are replaced with ROM_START.
ROM_START is only supported in some arches, as some arches have several
custom sections before text. These don't currently have ROM_START or
TEXT_START available, but that could be added with a bit of refactoring
in their linker script.
No SORT_KEYs are changed.
This also fixes an error introduced when TEXT_START was added, where
TEXT_SECTION_OFFSET was applied to riscv's common linker.ld instead of
to openisa_rv32m1's specific linker.ld.
Signed-off-by: Øyvind Rønningstad <oyvind.ronningstad@nordicsemi.no>
Implement a set of per-cpu trampoline stacks which all
interrupts and exceptions will initially land on, and also
as an intermediate stack for privilege changes as we need
some stack space to swap page tables.
Set up the special trampoline page which contains all the
trampoline stacks, TSS, and GDT. This page needs to be
present in the user page tables or interrupts don't work.
CPU exceptions, with KPTI turned on, are treated as interrupts
and not traps so that we have IRQs locked on exception entry.
Add some additional macros for defining IDT entries.
Add special handling of locore text/rodata sections when
creating user mode page tables on x86-64.
Restore qemu_x86_64 to use KPTI, and remove restrictions on
enabling user mode on x86-64.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
generated_dts_board.h is pretty redundant and confusing as a name. Call
it devicetree.h instead.
dts.h would be another option, but DTS stands for "devicetree source"
and is the source code format, so it's a bit confusing too.
The replacement was done by grepping for 'generated_dts_board' and
'GENERATED_DTS_BOARD'.
Two build diagram and input-output SVG files were updated as well, along
with misc. documentation.
hal_ti, mcuboot, and ci-tools updates are included too, in the west.yml
update.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
- In early boot, enable the syscall instruction and set up
necessary MSRs
- Add a hook to update page tables on context switch
- Properly initialize thread based on whether it will
start in user or supervisor mode
- Add landing function for system calls to execute the
desired handler
- Implement arch_user_string_nlen()
- Implement logic for dropping a thread down to user mode
- Reserve per-CPU storage space for user and privilege
elevation stack pointers, necessary for handling syscalls
when no free registers are available
- Proper handling of gs register considerations when
transitioning privilege levels
Kernel page table isolation (KPTI) is not yet implemented.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This code:
1) Doesn't work
2) Hasn't ever been enabled by default
3) We mitigate Spectre V2 via Extended IBRS anyway
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We use a fixed value of 32 as the way interrupts/exceptions
are setup in x86_64's locore.S do not lend themselves to
Kconfig configuration of the vector to use.
HW-based kernel oops is now permanently on, there's no reason
to make it optional that I can see.
Default vectors for IPI and irq offload adjusted to not
collide.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Nothing too fancy here, we try as much as possible to
use the same register layout as the C calling convention.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Includes linker script fragments for the kernel object
tables and automatic memory partitions. The data section
is moved to the end per the requirements of
include/linker/kobject.h.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
z_x86_thread_page_tables_get() now works for both user
and supervisor threads, returning the kernel page tables
in the latter case. This API has been up-leveled to
a common header.
The per-thread privilege elevation stack initial stack
pointer, and the per-thread page table locations are no
longer computed from other values, and instead are stored
in thread->arch.
A problem where the wrong page tables were dumped out
on certain kinds of page faults has been fixed.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add two new non-static APIs for dumping out the
page table entries for a specified memory address,
and move to the main MMU code. Has debugging uses
when trying to figure out why memory domains are not
set up correctly.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
