It is necessary to wrap the device pointer into data.
Which was done already on most of them when global trigger is enabled.
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
In sensors drivers, in gpio callback function :
The device structure in parameter is related to the gpio device.
Signed-off-by: laurence pasteau <laurence.pasteau@stimio.fr>
Some sensor drivers modify there struct's based on DT defines. In those
cases we need to make sure that DT_DRV_COMPAT is set on all the source
files associated with that driver. This updates any such files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Align all sensor drivers that are using stmemsc (STdC) HAL i/f
to new APIs of stmemsc v1.02.
Requires https://github.com/zephyrproject-rtos/hal_st/pull/3
Signed-off-by: Armando Visconti <armando.visconti@st.com>
All sensors were using legacy log module registeration method
where LOG_LEVEL was defined before registeration. This method
was error prone as it requires preserving includes order.
Replaced with LOG_MODULE_REGISTER(foo, level).
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Re-run with updated script to convert integer literal delay arguments
to k_thread_create and K_THREAD_DEFINE to use the standard timeout
macros.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Port the lis2mdl sensor driver on top of the lis2mdl_StdC
HAL interface (in modules/hal/st/sensor/stmemsc/).
Signed-off-by: Armando Visconti <armando.visconti@st.com>
move sensor.h to drivers/sensor.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In zephyr drivers should always use u32_t.
Using uint32_t here generates issues in the CI when NEWLIB_LIBC
is defined.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
i2c_burst_read can fail during read/write procedure. Therefore,
add a sanity check for its return value.
Fixes#11101
Coverity-CID: 189505
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Added support to LIS2MDL Magnetometer sensor provided
with following features:
- I2C interface
- Mag data
- Temperature data
- ODR configurable by config or at runtime
- Trigger mode selectable by menuconfig
- IRQ pin configurable (by dts or Kconfig)
- Hard Iron offset setting at runtime
- Include yaml file
Tested on ST MEMS IKS01A2 + NUCLEO STM32F411RE board.
LIS2MDL connected to I2C master interface (SPI 3 wire not
supported yet).
Test run with all ODR {10, 20, 50, 100} Hz in poll and
trigger mode.
GPIO IRQ dts configuration has been tested by adding
to boards/arm/nucleo_f411re/nucleo_f411re.dts file
this patch:
&i2c1 {
status = "ok";
clock-frequency = <I2C_BITRATE_FAST>;
+
+ /* ST Microelectronics LIS2MDL mag sensor */
+ lis2mdl-magn@1e {
+ compatible = "st,lis2mdl-magn";
+ reg = <0x1e>;
+ irq-gpios = <&gpioa 4 0>;
+ label = "LIS2MDL";
+ status = "ok";
+ };
};
and adding boards/arm/nucleo_f411re/dts.fixup with following
content:
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_LABEL
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_BASE_ADDRESS
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_BUS_NAME
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_IRQ_GPIOS_CONTROLLER
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_IRQ_GPIOS_PIN
For more info on this LIS2MDL please follow this link:
http://www.st.com/en/mems-and-sensors/lis2mdl.html
Signed-off-by: Mario Tesi <mario.tesi@st.com>
