It is necessary to wrap the device pointer into data.
Which was done already on most of them when global trigger is enabled.
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
We want to limit DT_ prefix to macros from devicetree.h and generation.
So rename DT_LIS2DH_INT* to just LIS2DH_INT*.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add I2C and SPI bus communication routines in separate files,
and register one or the other as read/write callbacks based
on bus selection in DTS.
This commit is fixing issue #22348 as well, as the SPI part
is handling in the proper way the CS GPIO part.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use the new pin and interrupt configuration API. Update all
devicetree bindings to add INT signal active level. Document active
level.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
After switching to new SPI API there is no need to reserve first dummy
byte in buffer and ignore that in application later on. Instead two
buffers can be specified, which is how it is done already in lis2dh
driver. The problem is that dummy byte is still part of the buffer, but
it clearly should no longer be. As an example we write 0x7 (bits to
enable XYZ axes) into CTRL2 instead of CTRL1 register. When reading
measurements on the other hand we have filled buffer starting from 0,
instead of 1 as the driver code has expected.
Fix driver in all places that use burst transfers by removing first
dummy byte from input/output buffer.
Fixes: 2f7e6b6d42 ("drivers/sensors: Switch lis2dh driver to new SPI
API")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
All sensors were using legacy log module registeration method
where LOG_LEVEL was defined before registeration. This method
was error prone as it requires preserving includes order.
Replaced with LOG_MODULE_REGISTER(foo, level).
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Use the named representation for no-wait to future-proof against a
change to the representation of timeout values.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Convert DT_.*_GPIO_{CONTROLLER,PIN,FLAGS} ->
DT_.*_GPIOS_{CONTROLLER,PIN,FLAGS)
Used the following commands to make these conversions:
git grep -l DT_.*_GPIO_CONTROLLER | xargs sed -i 's/DT_\(.*\)_GPIO_CONTROLLER/DT_\1_GPIOS_CONTROLLER/g'
git grep -l DT_.*_GPIO_PIN | xargs sed -i 's/DT_\(.*\)_GPIO_PIN/DT_\1_GPIOS_PIN/g'
git grep -l DT_.*_GPIO_FLAGS | xargs sed -i 's/DT_\(.*\)_GPIO_FLAGS/DT_\1_GPIOS_FLAGS/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Found a few annoying typos and figured I better run script and
fix anything it can find, here are the results...
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use auto-generated device tree macros in LIS2DH driver to avoid
usage of dts.fixup files. The triggered interrupt part has been
slightly hacked to automatically understand whether only int1 is
configured or both int1 and int2.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
FIX issue #10571 and #10593
atomic_xxx() functions expect the bit argument to be the
position index inside the target integer and not its
numerical representation (e. g. 5 means the 5th bit and not 32).
The original code could potentially override an adiacent variable.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert lis2dh accelerometer driver to get the device name as well
as i2c/spi slave information from device tree. Updates the build_all
test accordingly. (issue #11605)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Provide necessary error handling for `lis2dh_reg_read_byte` function
which might fail.
Also, use a common `status` variable to be used for storing the
error code.
Fixes#10590
Coverity-CID: 188733
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Fixes unused variable warnings for the adxl362 and lis2dh sensor
drivers. These warnings were found when updating the build_all tests to
include missing sensor drivers.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The return of memset is never checked. This patch explicitly ignore
the return to avoid MISRA-C violations.
The only directory excluded directory was ext/* since it contains
only imported code.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
* lis2dh 3 axis accelerometer support on SPI and I2C bus
* data ready and anymotion type of trigger support
Tested on Dynastream module D52QD2M4IA-A using SPI
Origin: based on Zephyr lis3dh driver
Change-Id: I2c4e9418b87f09c957bba8f73522bd78830bc809
Signed-off-by: Roger Lendenmann <roger.lendenmann@intel.com>
