This patch adds support for configuring the MAC address through the
Network Management API to the STM32 Ethernet driver.
Signed-off-by: Markus Fuchs <markus.fuchs@de.sauter-bc.com>
A 16bits on/off based PWM, found on MEC1501.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add RTC timer driver for CC13X2/CC26X2, and use it instead of systick
as system clock. It is necessary to use this timer for power
management support, so that the system can exit from deep sleep upon
expiry of timeouts.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Use the named representation for no-wait to future-proof against a
change to the representation of timeout values.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This commit adds:
1. pin definitions for SPI1 on PE12-15 on STM32L4 devices
2. SPI3 on PA15_SPI3_NSS
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The correct suffix name for selecting the GPIO for SPI Chip Select
is _CS_GPIOS_CONTROLLER and not _CS_GPIO_CONTROLLER.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
It seems that gpio_pin_disable_callback() has never been working
for that sensor as it was expected. We used there argument 'dev'
as its own (lis2dw12) device pointer. While this argument is a
gpio_port device pointer not lis2dw12 sensor device pointer. So
cfg->int_gpio_pin always tries to disable callback for some random
pin read from accidental data sector.
Signed-off-by: Michał Oleszczyk <oleszczyk.m@gmail.com>
console_register_line_input has been deprecated for at least 2 releases
so we can now remove it. Remove native_stdin_register_input that is
associated with console_register_line_input.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
For now there is only periodic data acquisition mode implemented.
This mode is quite power consuming. Based on datasheet in idle
state in periodic data acquisition mode SHT3X consumes 45uA but
in single shot mode 0.2uA. For many applications where power
consumption has to be kept as low as possible single shot mode
is the only choice. Tester on custom board NRF52832 + SHT31-DIS.
Signed-off-by: Michał Oleszczyk <oleszczyk.m@gmail.com>
When randomly generating MAC addresses they will always be
locally administrated addresses, so the LAA bit should be set.
The LAA bit is the 2nd bit of the 1st byte of the MAC address
not the 2nd bit of the 4th byte.
Fixes: #16452
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
No users of this driver after dropping quark platforms.
COUNTER_0_NAME was only defined by the QMSI driver and was defined but
not used in DTS fixup files of ateml_sam0 SoCs. Removing those leftover
defines as well.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
GPIO configuration flags will move and some that used to be in the low
8 bits are now higher, resulting in implicit constant conversion
overflows. Use a boolean data type to hold boolean values.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This driver was still using CONFIG_* values to determine its address,
IRQ, etc. Add a binding for an "intel,hpet" device and migrate this
driver to devicetree.
Fixes: #18657
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
In some hardware, e.g. ARC HS Development kit,the peripheral
space of DesignWare SPI only allowes WORD access,
byte acess will raise bus error.
This commit adds support for this case
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
* add pinmux driver. hsdk board has arduino, mikrobus and
pmod interfaces, which can be confiured for different function,
such as: gpio, spi, uart, iic.
* add introduction for arduino, mikrobus and pmod interfaces.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
Add support to STM IIS3DHHC the ultra-low noise, high-stability
three-axis linear accelerometer.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This reverts commit 0951ce2d34.
This change introduces regression on GPIO interrupts handling
when several GPIOs are configured.
Fixes#19177
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Such basic timer is found on MEC150x for instance.
Since instances have dedicated data, let's define specifice instance
based on unique DT base address definition.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Convert how we get the various chosen properties like "zephyr,console"
to use the new kconfig functions like dt_chosen_to_label.
Because of how kconfig parses things we define a set of variables of the
form DT_CHOSEN_Z_<PROP> since comma's are parsed as field seperators in
macros.
This conversion allows us to remove code in gen_defines.py for the
following chosen properties:
zephyr,console
zephyr,shell-uart
zephyr,bt-uart
zephyr,uart-pipe
zephyr,bt-mon-uart
zephyr,uart-mcumgr
zephyr,bt-c2h-uart
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The mcux CAN controller uses frame ID and position to calculate the
priority, but the driver expects chronological ordering.
This PR mimics this behavior by only using the last free message box.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Newly implement socket based communication on eswifi mainly to
achive TLS. Tested with Inventek ISM43362-M3G-L44.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
