Common uf2 partition configurations to avoid duplication in boards.
There appears to be a bit of confusion about exactly what a proper
UF2 partition map looks like for the nrf52840, so common dts
configurations should help to avoid confusion.
Configuration for SoftDevice v6 and v7 provided as thats what was
fouond in use in tree already.
Signed-off-by: Jacob Winther <jacob@9.nz>
Spi bus controller node names should follow recommended naming
convention from DT spec otherwise DTC will report a warning.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add property which indicates that UARTE support frame timeout
feature. Property is added to nrf54h20, nrf9280, nrf54l20 and
nrf54l15.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Add support for VBUS measuring part of the TCPCI compliant device.
This device should be used as a child-node for the more specific
TCPC driver and referenced by the vbus property in the usb-c
connector node.
Signed-off-by: Michał Barnaś <barnas@google.com>
Introduce GPIO-based driver for MIPI DBI class that allows MIPI DBI
type A and B displays to be used on general platforms.
Since each data pin GPIO can be selected individually, the bus pins are
set in a loop, which has a significant negative impact on performance.
When using 8-bit mode and all the data GPIO pins are on the same port,
a look-up table is generated to set the whole port at once as a
performance optimization. This creates a ROM overhead of about 1 kiB.
Tested 8-bit 8080 mode with ILI9486 display on nRF52840-DK board.
Signed-off-by: Stefan Gloor <code@stefan-gloor.ch>
HFXO is represented as a child of the oscillators node. A new node is
created because it requires its own properties (see the binding for more
details).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
LFXO is represented as a child of the oscillators node. A new node is
created because it requires its own properties (see the binding for more
details).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
- Create a new compatible: nordic,nrf53x-oscillators, as other series,
e.g. nRF54LX contain a similar but different IP (with PLL control,
etc.)
- Adjust DT: use recommended node name, remove redundant status okay.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Register all the lpi2c instances.
Add no-power-level property and update driver
to adapt no-power-level property.
Signed-off-by: Lucien Zhao <lucien.zhao@nxp.com>
This defines raspberrypi,pico-xosc along with a configurable startup
delay multiplier. On some boards, the XOSC takes longer to stabilize.
Signed-off-by: Xudong Zheng <7pkvm5aw@slicealias.com>
This fixes the following warning:
> unit address and first address in 'reg' (0x1002c0) don't match for
> /soc/dma@100200
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This fixes the following warning:
> unit address and first address in 'reg' (0x3fc70) don't match for
> /soc/peripheral@40000000/flash-controller@34000/flash@9fc70
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This fixes the following warnings:
> unit address and first address in 'reg' (0x40094000) don't match for
> /soc/peripheral@40000000/usbhs@144000
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This fixes the following warning:
> unit address and first address in 'reg' (0x3fc70) don't match for
> /soc/peripheral@40000000/flash-controller@34000/flash@9fc70
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This fixes the following warnings:
> unit address and first address in 'reg' (0x40094000) don't match for
> /soc/peripheral@40000000/usbhs@144000
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Now that we support internally connected channels we should make the
pinctrl configuration optional.
Signed-off-by: Corey Wharton <xodus7@cwharton.com>
Add MCO device nodes to the STM32 boards.
The set of supported boards are chosen to replace what is currently
supported in Kconfig.
Signed-off-by: Joakim Andersson <joerchan@gmail.com>
Add clock sources that can be output by the MCO on the stm32f1x and
stm32f10 connectivity line devices.
Signed-off-by: Joakim Andersson <joerchan@gmail.com>
Add board support for eval board ganymed_bob, which
is a break-out-board for both soc variants.
Variants of the soc are GBM and GEN1.
Signed-off-by: Sven Ginka <s.ginka@sensry.de>
Indicate in the STM32WB0 power controller binding that the SMPS output
current limitation is a feature only available on STM32WB05 and STM32WB09.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
