Run this test on lpuart10 with internal loopback enabled.
Use DTCM region for this test because in some local
variables are used for dma buffer which requires
non-cacheable
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
The test drivers.uart.basic_api.wide
can't work without keyboard
add harness: keyboard for this test
Signed-off-by: Marc Desvaux <marc.desvaux-ext@st.com>
change pins for the test uart_async_api loopback because the old pins
pb10/pb11 are now used for the I2C loopback test.
Signed-off-by: Marc Desvaux <marc.desvaux-ext@st.com>
This includes new overlays for boards supporting DMA, and one more test
to verify M0 boards both with and without DMA can be built when
requesting CONFIG_UART_ASYNC_API.
Signed-off-by: Diego Elio Pettenò <flameeyes@meta.com>
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
There are situations in which the async API for uart can be provided
by another driver (case in point, uart_rtt), and thus there is no valid
DMA controller for the uart_sam0 driver to talk with.
By separating the configuration, there's no need to exclude samd20-based
boards (that have no DMA peripheral) from the uart_async_api tests.
Signed-off-by: Diego Elio Pettenò <flameeyes@meta.com>
Co-authored-by: Gerson Fernando Budke <nandojve@gmail.com>
It is the arduino_i2c node on the board.
Also remove comment from arduino_r3_connector as the arduino_i2c
node can be used.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
This board is a relatively inexpensive development kit for USB-PD
controllers, using an UPD301C controller.
This Zephyr config includes support for:
* UART (present on he debug header of the board), tested with the
hello_world sample application;
* the one standalone LED (CAP_MIS), tested with the blinky sample
application;
* the rotary encoder (PDO_SEL), via ADC, tested with the adc sample
application;
* the current sense amplifier (I_SENSE), currently untested;
* the SPI bus, connected internally in the UPD301C to the UPD350;
* the I2C bus, exposed on the debug header, currently untested.
Note that the drivers.uart.async_api.rtt has to be disabled, as it is
for other m0 boards with no dma or it fails to build.
Signed-off-by: Diego Elio Pettenò <flameeyes@meta.com>
Refactor the ESP32 target SOCs together with
all related boards. Most braking changes includes:
- changing the CONFIG_SOC_ESP32* to refer to
the actual soc line (esp32,esp32s2,esp32s3,esp32c3)
- replacing CONFIG_SOC with the CONFIG_SOC_SERIES
- creating CONFIG_SOC_FAMILY_ESP32 to embrace all
the ESP32 across all used architectures
- introducing CONFIG_SOC_PART_NUMBER_* to
provide a SOC model config
- introducing the 'common' folder to hide all
commonly used configs and files.
- updating west.yml to reflect previous changes in hal
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Modify the test to not rely on assumption that RX buffer is released
when it is fully released. RX buffer maybe released after any RX_RDY
event within the buffer, e.g. after each timeout driver may be
switching to the new buffer.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Configure the overlay to have DMA transfer with high priority
when running the tests/drivers/uart/uart_async_api on nucleo_f103rb.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Twister now supports using YAML lists for all fields that were written
as space-separated lists. Used twister_to_list.py script. Some artifacts
on string length are due to how ruamel dumps content.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
drivers.uart.async_api.rtt test started failing on xmc45_relax_kit
after f423ec255f which set
CONFIG_SERIAL_SUPPORT_ASYNC=y if uart rtt is enabled. This conflicts
with the xmc4xxx uart driver which sets the same symbol conditionally
if the dma is enabled in the device tree. The conflict created some
warning during compilation causing the CI to fail.
All the uart_async tests were disabled in
71d0394752. This commit re-enables the
test on xmc45_relax_kit and only excludes the rtt test that's failing.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Instead of checking the `rx-pin` property that got deprecated and
removed, the test needs to check the `disable-rx` property.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This test needs a counter device. Introduce a node label that allows
selecting one in dts overlays instead of using hard-coded `timer0`.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Modifying counter drivers (rtc and timer) to rely completely on
device tree and not on Kconfig of MDK flags.
Adapting dtsi for all SoCs and adapting test configuration.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Unify set of the pins on `nrf52840dk_nrf52840`, which is used by
`gpio_loopback` fixture.
Signed-off-by: Katarzyna Giądła <katarzyna.giadla@nordicsemi.no>
Add support for the Wio Terminal board, including support of its
sensors, MicroSD and LCD. Tested with samples already available.
Signed-off-by: Joel Guittet <joelguittet@gmail.com>
Adds overlay and config for xmc45_relax_kit.
The Kconfig entry CONFIG_SPEED_OPTIMIZATIONS=y must be set
to pass the test at baudrate 921600 bps.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Use the macro as defined by the
include/zephyr/dt-bindings/dma/stm32_dma.h to configure the
dma channel.
Use the STM32_DMA_PERIPH_TX or STM32_DMA_PERIPH_RX value.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
UARTs are mostly assumed to exist in Zephyr but some hardware wishes
to exclude the tests. Adds a uart tag to the test case to ensure
ignoring is possible.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Align configuration for nrf52840dk to use the same loopback pins
for uart_async_api and uart_mix_fifo_poll tests.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Fix all line-length errors detected by yamllint:
yamllint -f parsable -c .yamllint $( find -regex '.*\.y[a]*ml' ) | \
grep '(line-length)'
Using a limit is set to 100 columns, not touching the commandlines in
GitHub workflows (at least for now).
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Currently the test only pushes 1 byte in each call to uart_fifo_fill().
This doesn't test cases where the driver can accept more than 1 byte
in the fifo.
Instead, try to push all the bytes in the uart_fifo_fill() call.
Internally the driver may only accept 1 byte, in which case the test
will be equivalent as before the patch.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
integration_platforms help us control what get built/executed in CI and
for each PR submitted. They do not filter out platforms, instead they
just minimize the amount of builds/testing for a particular
tests/sample.
Tests still run on all supported platforms when not in integration mode.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit configures the testcase to run on the
stm32u5x5 target boards. USART2 is selected
Pins Tx and Rx (PD5 PD6 on CN9) must be connected on the HW board
to pass the test.
The USART transfer uses the GP DMA transfer with request
27 and 26 on 2 DMA channels (0-15).
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit configures the testcase to run on the
stm32u585 target boards. USART3 is selected
Pins Tx and Rx (PD8 PD9 on CN14) must be connected on the HW board
to pass the test.
The USART transfer uses the GP DMA transfer with request
28 and 29 on 2 DMA channels (0-15).
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Many driver samples or tests only had 'drivers' as the tag, without a
tag indicating what driver that is exactly, so add some missing tags.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
