Fixed pinout in adc overlays to align with board
Allowed adc driver sample
Added overlay for gpio_basic_api test support
Added overlay for i2c_api test support
Signed-off-by: Pavlo Havrylyuk <pavlo.havrylyuk@infineon.com>
This follows the same convention that has already been adopted by Intel
Alder Lake and Raptor Lake boards.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add `yd_esp32` board:
- Model name: YD-ESP32
- Manufacturer: VCC-GND® Studio
- Espressif module: ESP32-WROOM-32E
Signed-off-by: Julio Cesar <hi@jcsx.dev>
Remove virtual esp32 board and replace it with the
real word boards:
- esp32_devkitc_wroom
- esp32_devkitc_wrover (with PSRAM option)
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Add DT and kconfig overlays for the nrf52_bsim so this test can be run
in this board too.
This simulated board supports short-circuiting pins
either programmatically or thru configuration files,
but it does not support a pull in an input being able to drag
a non driven output, so we need to skip the pull test.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The below is the unit test result for the driver and kernel of
it82xx2_evb board.
GPIO/gpio_basic_api: PASS
I2C/i2c_api: PASS
Flash: PASS
UART/uart_basic_api: PASS
PWM/pwm_api: PASS
WDT/wdt_basic_api: PASS
KSCAN/kscan_api: PASS
kernel/sched/schedule_api: PASS
kernel/sched/preempt: PASS
kernel/timer/timer_api: PASS
kernel/sleep: PASS
ADC/adc_api: PASS.
ADC note: conversion time~=61.6us
sample time delay~=60us
wait voltage stable time~=202.8us
Set sampling time to 500us will pass for ADC test.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Add support for the following boards:
- esp32s2_saola
- esp32c3_devkitm
- esp32s3_devkitm
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Microchip XEC devices specify GPIO pin using octal numbering and
organize pins in banks of 32. Chip documentation does not use
bank naming rather naming each pin by its octal number. This has
led to the developer having to calculate the bit position of a pin
in its 32-bit bank when a specifying the pin for GPIO usage. We
created a set of defines for all possible GPIO pins that specify
the DT GPIO bank name used in the chip level DTSI files and the
bit position in that bank.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
This is a follow-up to commit 25d7a09aa5.
The arduino_serial/uart1 node should not be enabled by default because
even if an application does not use it, the default CONFIG_SERIAL=y
setting causes that it is anyway initialized, so the UARTE peripheral
acquires its assigned pins (and they cannot be used in other way) and
its enabled receiver causes increased current consumption (by ~500 uA)
when the CPU is sleeping. This affects e.g. the boards/nrf/system_off
sample.
Applications that actually need to use this UART or shields that use
the arduino_serial node should enable the node explicitly.
Keep this node disabled by default for the nrf52840dk_nrf52840 board
and also for boards whose definitions are mostly copies of the above:
nrf52833dk_nrf52833 and nrf21540dk_nrf52840.
Update also accordingly a few overlay files in tests/ that were
disabling this node because of the pins it undesirably acquired.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support to run the test on NXP S32Z27, the wiring connection
is needed as describe in overlay file
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Now that gpio drivers are enabled based on devicetree we can remove
any cases of them getting enabled by *defconfig and proj.conf files.
Signed-off-by: Kumar Gala <galak@kernel.org>
This commit changes the pin assignment for the gpio_basic_api
test case because A0 was conflicting with the testcase
tests/drivers/dac/dac_loopback.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Enable testcases under tests/drivers/gpio/gpio_basic_api
To run in twister, "-X gpio_loopback" parameter is needed.
Signed-off-by: Yinfang Wang <yinfang.wang@intel.com>
Enable testcases under tests/drivers/gpio/gpio_basic_api
To run in twister, "-X gpio_loopback" parameter is needed
Signed-off-by: Hu Zhenyu <zhenyu.hu@intel.com>
This patch adds GPIO and 96board LS (Low Speed)iexpansion connector
support for SiFive HiFive Unleashed and also enables GPIO basic test.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Add DT overlay to run gpio_basic_api test on GD32VF103V-EVAL board. In
order to make testing easy a couple of accessible pins have been
selected: PD0 and PD1 pins exposed via JP13 and JP4 respectively.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Remove the manual selection of `CONFIG_GPIO_EMUL` as it is now enabled
by default when devicetree nodes exist.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Add DT overlay to run gpio_basic_api test on GD32F403Z-EVAL board. In
order to make testing easy a couple of accessible pins have been
selected: PD0 and PD1 pins exposed via P3 and P2 respectively.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add DT overlay to run gpio_basic_api test on GD32F450I-EVAL board. In
order to make testing easy a couple of accessible pins have been
selected: PC6 and PC7, the last 2 pins on the DCI camera 2.54" header.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Extend test configuration for nrf52840dk to validate use of
GPIO SENSE and GPIOTE IN event for edge interrupts.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
For some reason, provided pin configuration for nucleo_f103rb
is not able to detect gpio callback issues.
Move to other pin combination which detect pin callback issues.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Adding adp_xc7k_ae350 board support based on andes_ae350 soc. It's base
support and only contains uart/gpio drivers.
Signed-off-by: Jim Shu <cwshu@andestech.com>
This is now failing an edtlib check for unknown vendor prefixes.
I can't find a reason to use a vendor prefix in application-local
bindings like this, so just remove it wherever it appears by
normalizing to test-foo-compat instead of test,foo_compat or
test,foo-compat.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Introduce the npcx9m6f_evb board driver. NPCX9M6F_EVB board is a
development platform to evaluate the Nuvoton NPCX9 series
microcontrollers. This board needs to be mated with part number
NPCX996F.
It also includes:
1. Add CONFIG_BOARD_NPCX9M6F_EVB definition for adc test suite.
2. Add npcx7m6f_evb.overlay file for gpio test suite.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This commit provides the necessary overlay to make the test pass
on the QuickFeather hardware.
Signed-off-by: Jan Kowalewski <jkowalewski@antmicro.com>
This adds support for emmulated GPIO (CONFIG_GPIO_EMUL=y) and
additionally allows BOARD=native_posix and
BOARD=native_posix_64 to run the gpio_basic_api test suite.
Fixes#26477
Signed-off-by: Christopher Friedt <chrisfriedt@gmail.com>
Add gpio support for Nuvoton NPCX series. This CL includes:
1. Add GPIO device tree declarations.
2. Introduce wui_maps property in yaml file to present relationship
between Wake-Up
Input (WUI) and 8 IOs belong to the device.
3. Zephyr GPIO api implementation.
4. GPIO callback functions implementation with MIWU api functions.
5. Overlay file for gpio basic tests
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
GPIO 050/051 are being used for tachometer sensor as
CONFIG_TACH_XEC is enabled by default. So for the gpio_basic_api
test, another set of GPIOs are needed. GPIO 156/157 are chosen
as they are (more or less) dedicated for two LEDs on board and
not being used for other functions (pinmux-wise).
Fixes#25272
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Convert driver to use the new device tree macro's instead of
dts_fixup.h based macros. This moves us closer to removing both
dts_fixup.h and per instance Kconfig symbols.
The pinmux_mchp_xec is also being updated since it's using DT
from GPIO.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
No in-tree boards support the NINT signal on an SX1509B IO extender,
so test using custom overlays/configurations for the Particle Xenon
board using an SX1509B breakout board.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Changes to Kconfig vs devicetree resulted in uart1 being enabled,
which steals the test pins away from the test.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The board name for the Thingy:52, so far known as nrf52_pca20020, is
renamed to thingy52_nrf52832. Its documentation and all references to
its name in the tree are updated accordingly. Overlay and configuration
files specific to this board are also renamed, to match the new board
name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Additionally remove udoo_neo_full_m4.conf from gpio_basic_api test since
the Kconfig symbols don't need to be set anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The nRF52840 DK board target, so far known as nrf52840_pca10056,
is renamed to nrf52840dk_nrf52840.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
