Set an overlay to build tests/drivers/flash/common/
drivers.flash.common.disable_spi_nor when the SPI NOR exists
but test does not use it
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add a special testcase to test any stm32 target
The expected flash size is given by the config FLASH_SIZE (in bytes)
and stm32 flash driver API function should return the same value
Do not run on the stm32wb55 nucleo as 216K are reserved among the 1MB
(only 808K declared but mcu has 1MB)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Since the test is hardcoded to prioritize testing a spi nor flash if
there is one, add a twister case for disabling that config in case if a
platform should also test some other flash which is present, such as
internal SOC flash. I.e, relevant platforms would be those which have
both internal and spi nor flash enabled in DT.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Since siwx917_rb4338a now declare a storage_partition,
siwx917_rb4338a.overlay is not required anymore.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
For the flash with the block size equal to or smaller than 64 bytes,
using a specific "32" bytes for adding for destination_offset and "32"
bytes for subtracting the size that need to copy is not correct.
As a solution, I will add one-fourth of a block size for the
destination_offset and modify the size that need to copy to
[block size + one-fourth of a block size].
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
QSPI NOR driver non-Quad mode was not tested before.
Add configuration that uses driver in the non-Quad mode.
Signed-off-by: Bartosz Miller <bartosz.miller@nordicsemi.no>
Add some overlay files for the silabs xg29_rb4412a board to enable tests
on the board. Also add the platform to some testcase.yaml files.
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
Add low-power-write property to MSC device tree node, set
MSC_WRITECTRL_LPWRITE if enabled.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Extend several flash samples and tests so that they can also be used
with "jedec,mspi-nor" devices.
Add configurations needed for the nrf54h20dk/nrf54h20/cpuapp target.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Create common source code to use for supporting HyperFlash.
Rename 'FLASH_NXP_S32_QSPI_NOR_SFDP_RUNTIME' to
'FLASH_NXP_S32_QSPI_SFDP_RUNTIME' as a common kconfig.
Add the 'max-program-buffer-size' property to use for
setting memory pageSize, instead of using
'CONFIG_FLASH_NXP_S32_QSPI_LAYOUT_PAGE_SIZE' for setting.
Add the 'write-block-size' propertyto use for setting
the number of bytes used in write operations, it also
uses to instead of the 'memory-alignment' property.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
Convert qspi and hyperflash to variants instead of revisions by popular
demand.
And convert evkb into a revision instead of a different board.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Now expected vs read size will be logged in case of error
to make it easier to understand problem or correct test
settings.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
This is a follow-up to 21475774fc,
extending the number of tests and samples that use the new L05 and L10.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
flash_copy() is performed on a page.size span but following flash_read()
verification step is performed on EXPECTED_SIZE length (512).
This doesn't work on devices where page.size is lower than EXPECTED_SIZE,
such as STM32L1 where page size is 256.
To fix this, perform verification on the smalest value between page.size
and EXPECTED_SIZE.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Enable flash driver test for MAX32690 boards.
Signed-off-by: Mert Vatansever <mert.vatansever@analog.com>
Signed-off-by: Sadik Ozer <sadik.ozer@analog.com>
Use EXTRA_CONF_FILE in sample yaml files,
that replaced deprecated OVERLAY_CONFIG
since the Zephyr v3.4 release.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
test_flash_erase() requires that the expected[] array contains
pseudo-random data. However, the expected[] array would only
be initialized once before all tests are run using the setup
callback.
Instead, use the before() callback to randomize data before
each test in the suite, since there is otherwise no guarantee
that test_flash_erase() will be run directly after the
expected[] array has been randomized.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Align all existing samples/tests/applications which
contains nrf54l15pdk/nrf54l15/* by adding
nrf54l15dk/nrf54l15/* to enable twister builds.
Signed-off-by: Katarzyna Giądła <katarzyna.giadla@nordicsemi.no>
Signed-off-by: Grzegorz Chwierut <grzegorz.chwierut@nordicsemi.no>
Fix flexspi xip configuration issue regarding code relocation
due to the order of kconfig defaults being sourced
The flexspi setup was not being relocated to an on chip location
Also remove rt1060 conf file in flash common test which changes the
code relocation location to RAM, just keep as ITCM for all M7 which
as of now all have ITCM from NXP with flexspi.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
