Add support for the Renesas RA Event Link Controller, including
driver sources, Kconfig, and Devicetree bindings.
Signed-off-by: Khanh Nguyen <khanh.nguyen.wz@bp.renesas.com>
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
Migrate renesas,ra-agt-counter implementation to use hal_renesas.
Add additional AGT_CLOCK_SUBCLOCK count source.
Add constraint for counter resolution to 32 or 16 bit variant.
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
Add the nxp,rtxxx-dsp-ctrl driver.
Responsibility of this driver is to load code executed by Xtensa-family
cores on NXP i.MX RTxxx microcontrollers and to control their run.
Signed-off-by: Vit Stanicek <vit.stanicek@nxp.com>
Intial serial driver support for RX MCU, this driver utilize
the SCI HWIP for uart communication
Current support include polling API and Interrupt driven API,
some of the code is using Renesas RX Driver Package (RDP) as
hal layer
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Signed-off-by: Sang Tran <sang.tran.jc@renesas.com>
Add serial driver support for RZ/N2L
Signed-off-by: Hoang Nguyen <hoang.nguyen.jx@bp.renesas.com>
Signed-off-by: Nhut Nguyen <nhut.nguyen.kc@renesas.com>
Removing period, duty and polarity configuration from
channel devicetree. At boot time, only minimal setup like
pinctrl, prescaler, etc should be initialized. PWM signal
is produced by using pwm_set* API
Also after this change, PWM period, duty are changed at the
next counter period boundary
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
First commit to add support for gpio interrupt on Renesas RA
- Add support for external interrupt driver
- Add support for gpio interrupt config
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
Added a binding description for the PPIB peripheral and added the device
tree nodes of the PPIB instances to the nRF54L15 and nRF54L20.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
- boards: renesas: Add support for agt.
- drivers: counter: Add support for counter driver use agt
- dts: arm: Add support for agt.
- dts: bindings: Add support for agt counter driver.
- soc: renesas: Add support for agt counter driver.
- samples: drivers: counter: alarm: Add support for RA8
This is initial support with only basic functionality for counter
operation on Zephyr using AGT hardware, current support for
count source is limited to LOCO and PCLKB, other count source
like underflow signal external pin or AGTIO from another AGT
channel will be added in later support
Signed-off-by: Ha Nguyen <ha.nguyen.fz@bp.renesas.com>
Signed-off-by: Thao Luong <thao.luong.uw@renesas.com>
Signed-off-by: Duy Phuong Hoang. Nguyen <duy.nguyen.xa@renesas.com>
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
Add new binding and a node to nrf54h20. Update Kconfig and nrfx_config
to include nrfx_tbm driver when node with that compatible is enabled.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Correct license identifiers in two files copied from internal Nordic
repositories that were not properly adjusted for Zephyr:
- dts/bindings/flash_controller/nordic,rram-controller.yaml (added in
commit 3a8ee7df91)
- dts/bindings/misc/nordic,nrf-dppic-local.yaml (added in commit
796d09d2a6)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Move low-level GPIO functions to a separate file and use GPIO driver
API if low-level GPIO support is not available for the platform.
Allows alternative pin configuration using only two pins, clk and dio.
Improve binding description.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Add CMSIS-DAP compatible controller which is a handler between
the host interface and SWD driver. The controller follows CMSIS-DAP
reference implementation. It expects a request buffer from the host
interface, splits it to simple transfers and forwards to the DP driver,
and finally returns a response buffer to the host.
Interface to the host can be implemented with USB HID device support.
Controller implements only SW-DP support and is tested
with pyOCD and ADIv5.x.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Add Serial Wire Debug Port interface driver API and bit-bang driver.
The driver requires a simple Hardware Interface Circuits (HICs),
where signals CLK, DOUT, DIN, ENn, OE_ENn, RESETn
are connected to board GPIOs and buffered signals SWD_CLK and SWD_DIO
to the target.
Signal OE_ENn controls the direction of the Serial Wire (SWD_DIO),
ENn the buffers SWD_CLK possibly others and enables/disables HIC.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
And add the corresponding bindings.
Move alse the already existing bindings for nrf-dppic, nrf-ppi,
and nrf-ipc so they are located together with the new ones and
in more appropriate folders (DPPIC and PPI peripherals are not
related to ARM, and IPC is for sending and receiving events,
not messages, so ipm/ does not seem to be the best fit for it).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add a new #nordic,ficr-cells property, so that we can specify a FICR
offset in a phandle-array, e.g.
nordic,ficrs = <&ficr 0xff>;
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add code to configure and program Lcu, Trgmux and Emios_Icu IPs to
get the the rotations by the motor in radians.
Co-authored-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
Co-authored-by: Mayank Mahajan <mayankmahajan.x@nxp.com>
Signed-off-by: Sumit Batra <sumit.batra@nxp.com>
The Device Multiplexer (devmux) is a pseudo-device that can
be used to select between multiple included sub-devices.
It is experimental, but its current use is in system
remediation. Take for example, the scenario where the
system console and log subsystem both have the uart backend
enabled. The case may arise, where the chosen backing uart
could be an abstraction of another very high-bandwidth bus
- such as a PCIe BAR, a UDP socket, or even even just memory.
If the "service" (for lack of a better term) that backs this
abstract "uart" experiences an error, it is of critical
importance to be able to switch the system console, uart log
backend, or whatever to another uart (semi-transparently) in
order to bring up a shell, continue to view system logs, or
even just support user console I/O.
Signed-off-by: Christopher Friedt <cfriedt@meta.com>
Adding initial support for Renesas RA UART.
To avoid complicating initial code for supporting the SoC,
I have implemented only the bare minimum for now.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
This introduces pwm capture shim driver for NXP S32 EMIOS,
the driver uses SAIC mode that is supported for all channels,
to capture the counter value on each edge for period/pulse
measurement
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
This enables and declares interrupt handlers for eMIOS,
the handlers defined and implemented at HAL, the driver
takes the name for each id from interrupt-names devicetree
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
This PR adds a misc driver for NXP S32 eMIOS peripheral.
eMIOS provides multiple unified channels (UCs), there are
several channels can be used as reference timebase
(master bus) for other channels. At this time, the
driver does initialize global configuration for eMIOS
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Added a generic driver for RaspberryPi Pico PIO.
This driver is an intermediate driver for abstracting the PIO
device driver from physical pin configuration.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
Signed-off-by: Ionut Catalin Pavel <iocapa@iocapa.com>
Intel DSP Communication Widget is a device for generic sideband
message transmit/receive between IPs in a SOC.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
DTS property attributes are (by default) not required.
Explicitly specifying `required: false` is redundant.
Perhaps a warning to that effect would be useful.
Signed-off-by: Chris Friedt <cfriedt@meta.com>
Force cache-size to 0 and treat flashdisk as read-only when backing
partition has read-only flag set. This allows users to save RAM when the
application does not write to the flashdisk, e.g. when a predefined FAT
filesystem is used.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Add bindings to describe a block storage device based on flash map
partition.
Co-authored-by: Johann Fischer <johann.fischer@nordicsemi.no>
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Use the clock control API to enable peripheral clocks. Note that both
GPIO and pinctrl drivers are updated at once since they share some IP
blocks.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
ICI (Inter-Core Interrupt Unit) interrupts and priorities were hardcoded
in C files. This patch moves this information to Devicetree and updates
code to make use of it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
sysconf base address was hardcoded in <soc.h>. Create a new compatible
and define it in Devicetree, where hardware needs to be described.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
