The utility may be used during development stage to get
ambiq platform specific timing parameters for mspi devices.
Signed-off-by: Swift Tian <swift.tian@ambiq.com>
This device driver supports ISSI is25w/lx032/64 series flash.
Only extended SPI mode(1s-1s-1s, 1s-8s-8s, 1s-1s-8s) is implemented.
Signed-off-by: Swift Tian <swift.tian@ambiq.com>
Add support for setting RGMII RX and TX internal delays via DT properties:
`ti,rx-internal-delay` and `ti,tx-internal-delay`.
Signed-off-by: Venkatesh Odela <venkatesh.odela@amd.com>
Remove gpio clock management from the GPIO driver when running on the
cortex-m33 on the mp2 and gpio clocks are managed by the cortex-A, being
the resource manager, allowed by the Resource Isolation Framework (RIF).
Also add a specific binding for the mp2 gpio to make clock property
optional.
Signed-off-by: Youssef Zini <youssef.zini@savoirfairelinux.com>
Introduce DeviceTree binding for the STM32MP2 RCC clock controller,
enabling support for STM32MP2-specific clock configuration in Zephyr.
Update Kconfig.stm32 to add a dependency on STM32MP2 configuration,
allowing the use of STM32 LL RCC features when targeting STM32MP2
devices.
Add header for STM32MP2 per peripheral clock definitions.
Signed-off-by: Youssef Zini <youssef.zini@savoirfairelinux.com>
Support three different FIFO contents which are selectable through
a new DT property, fifo-mode-sel, which may be set to one of the
following values:
- 0x0 # 1x Accelerometer @12bit and 1x temperature @12bit samples
- 0x1 # 1x Accelerometer @16bit sample
- 0x2 # 2x Accelerometer @8bit samples (previous and current)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This commit adds support for configuring the power/performance
profile for the siwx91x device using a generic
'power-profile' property in DeviceTree.
The property is available for NWP nodes,
allowing flexible selection of power management
profiles per application or board via overlay.
Signed-off-by: S Mohamed Fiaz <fiaz.mohamed@silabs.com>
Add support for the Renesas RA Event Link Controller, including
driver sources, Kconfig, and Devicetree bindings.
Signed-off-by: Khanh Nguyen <khanh.nguyen.wz@bp.renesas.com>
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
Add information about nfct node status. For cpuapp status is irrelevant
because NFCT is by default assigned to cpuapp but for cpurad node needs
to have reserved status.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Configure the active discharge feature for both the BUCK and LDO/LDSW
blocks through the appropriate registers.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Two DMA channels are assigned to AES channels A and B respectively.
Each channel A/B has an interface to control the conditions that will
generate requests on the related DMA channel: trigger condition,
R/W address, and DMA done action.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
The intention was to use the "interface-name" string property in the
interface string descriptor, but using the label property is acceptable
again. Therefore, allow the use of the DT label property string in the
interface string descriptor.
Follow exactly the same approach as in the CDC ACM implementation
introduced in the commit b0791400f6
("usb: device_next: cdc_acm: allow setting the interface description").
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
TI MSPM0 SoC series has General Purpose Timer and Advanced control timers
with Counting module, Capture block (measure input signal period/time) and
Compare block (to generate time expiry, output waveform like PWM).
Add a support for counter driver with alarm and counter top functions.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
Add property which indicates that PWM instance supports IDLEOUT
feature. Add property to all instances that supports it.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Two DMA channels are assigned to TX and RX respectively:
- A TX DMA request is asserted when there is space in the FIFO.
- A RX DMA request is asserted when data is in the FIFO.
When DMA is enabled for a peripheral, the DMA transfer completion is
signaled on the peripheral's interrupt only (here UART's interrupt).
It is not signaled on the DMA dedicated interrupt.
Also, when DMA is enabled for a peripheral, the DMA controller stops
the normal transfer interrupts for this peripheral from reaching the
NVIC (the interrupts are still reported in the interrupt registers of
the peripheral). Thus, when a large amount of data is transferred using
DMA, instead of receiving multiple interrupts from the peripheral as
data flows, the NVIC receives only one interrupt when the transfer
completes (unmasked peripheral error interrupts continue to be sent
to the NVIC).
Signed-off-by: Julien Panis <jpanis@baylibre.com>
The ADC has a dedicated interface for communicating with the DMA.
The ADC module provides four interrupt sources (one for each
conversion result storage register) which can be configured to
source the DMA trigger.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Add MPS4 pinctrl support by referring to
`mps4/common/partition/platform_base_address.h`
from TF-M's main branch.
Signed-off-by: Sudan Landge <sudan.landge@arm.com>
Initial commit for SPI driver support on RSK_RX130@512KB board
with RSPI module
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Signed-off-by: Minh Tang <minh.tang.ue@bp.renesas.com>
Since `VirtIO` is not the official notation,
unify the name to `VIRTIO`.
In the text, `Virtio` and `virtio` can also be used
depending on the context.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Add RTIO async and RTIO stream functionalities that enables,
among all the other things, the sensor data streaming from FIFO.
RTIO stream supports following triggers:
- SENSOR_TRIG_FIFO_WATERMARK
- SENSOR_TRIG_FIFO_FULL
- SENSOR_TRIG_DATA_READY
Following FIFO parameters has to be defined in device tree to
correctly stream sensor data:
- fifo-watermark
- accel-fifo-batch-rate
Currently the driver can decode FIFO content with Accelerometer
16-bit samples.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This commit adds serial driver support for npck3.
Signed-off-by: Alvis Sun <yfsun@nuvoton.com>
Signed-off-by: Tom Chang <CHChang19@nuvoton.com>
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Added secure proxy mailbox driver for supported devices using
the binding ti,secure-proxy. This is used to communicate with
a device manager running on a separate core via a secure proxy
mailbox for TI K3 devices. Required for enabling TISCI layer
communication.
Refer: https://software-dl.ti.com/tisci/esd/latest/1_intro/TISCI.html
Tested on MAIN_CORTEX_R5_0 on AM243x EVM.
Refer:https://www.ti.com/lit/pdf/spruim2
Co-developed-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Dave Joseph <d-joseph@ti.com>
Initial driver for the icm40627 from Invensense/TDK, a 6-axis
accelerometer with gyroscope and temperature sensing capabilities.
Signed-off-by: Florijan Plohl <florijan.plohl@norik.com>
This patch adds the ADC driver for TI K3 family of SoCs. Technical
reference can be found in the Technical Reference Manual (TRM) of the
board.
Signed-off-by: Amneesh Singh <a-singh7@ti.com>
Support OSPI flash driver on EK-RA8M1 and EK-RA8D1 with ospi_b
and S28HL512T flash.
Signed-off-by: Tri Nguyen <tri.nguyen.wj@bp.renesas.com>
Signed-off-by: Thao Luong <thao.luong.uw@renesas.com>
Add VirtIO Entropy driver.
The `virtio,device4` is a somewhat unfamiliar naming convention,
but it follows the convention used in Linux.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
This commit add support for the Omnivision OV9655 sensor,
a 1.3MPix Color SXGA (1280x1024 sensor).
Current driver only allow output of 320x240 and 160x120
resolution either in RGB565 or YUYV.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
