Assembler files were not migrated with the new <zephyr/...> prefix.
Note that the conversion has been scripted, refer to #45388 for more
details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Some SOCs, such as the RT1064 and RT1024, use internal flash and don't
define pinmux settings for the flexspi. Don't check the return code of
pinctrl_apply_state, because the flexspi driver will fail to initialize
when the pin mux settings are simply not required.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add SD response type masks, to allow drivers to mask out the
SPI or SD native mode response type based on the SD host controller
mode they use.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Use the UPLLCK clock for the CAN controller as recommended by the Atmel SAM
E70 data sheet.
Move the configuration of the clock prescaler from Kconfig to devicetree
and limit it to the values recommended by the SAM E70 datasheet.
Fixes: #45012
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
This is a follow-up to commit fd7633126e.
For some reason the above commit added several switch cases without
required break statements. In effect, the same pin could get assigned
to multiple signal lines in QDEC or QSPI peripherals if not all pins
were defined for them in devicetree, and consequently these peripherals
could not work properly.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Allow CTS line to determine UART shutdown for any sleep mode.
This allows lower average current consumption for LITE
HIBERNATE mode.
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Added chosen syntax in Device Tree to abstract the IPC device that is
used with the IPC service module in the Bluetooth HCI RPMsg driver.
Ported affected boards to declare this alias.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
Update the Zephyr include paths to be compatible with removing
`CONFIG_LEGACY_INCLUDE_PATH` in the future.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Respect the configured values for how long the domain takes to turn on,
and how long the domain needs to be off for before it can be repowered.
As these actions can block, guard the transition function with
pm_device_action_can_block. To avoid system PM being able to turn the
domain off but not back on again, guard the entire implementation.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Enables the Intel SSP driver by default when the DAI driver class is
enabled (CONFIG_DAI=y) and a compatible devicetree node
("intel,ssp-dai") is enabled.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Use `DT_REG_ADDR_BY_NAME` and `DT_REG_SIZE_BY_NAME` to access register
properties from dts.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
Adds addresses and names for individual CSR registers to device tree.
This way liteuart driver no longer depends on CSR data width being 8
bits.
Also when register names or their number changes, then overlay generated
by LiteX will be incompatible with one defined here.
This should make finding breaking changes easier.
I also appended `_ADDR` suffix to defines, to distinguish them from
normal values like `LITEETH_EV_RX`.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
Adds addresses and names for individual CSR registers to device tree.
This way liteuart driver no longer depends on CSR data width being 8
bits.
Also when register names or their number changes, then overlay generated
by LiteX will be incompatible with one defined here.
This should make finding breaking changes easier.
I also appended `_ADDR` suffix to defines, to distinguish them from
normal values like `UART_EX_TX`.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
Adds addresses and names for individual CSR registers to device tree.
This way timer driver no longer depends on CSR data width being 8 bits.
Also when register names their number changes, then overlay generated by
LiteX will be incompatible with one defined here.
This should make finding breaking changes easier.
I also updated register names to those used in current LiteX and
appended `_ADDR` suffix to defines which lacked them.
Because register `total` was renamed to `value` and `update_total` to
`update_value` I updated variables accordingly as well.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
Host might send command or data immediately after EC read the
KBC input buffer (IBF gets cleared).
This change make sure EC won't get wrong event type in IBF ISR.
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
Move period and pulse computation to right before
the channel enable code.
That fixes the inability to disable the channel by
providing the period of 0.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
The STM32u% series of processors has a unique set of clock sources for
the FDCAN peripheral. This brings the selection in line with the
existing can_stm32fd clock selection Kconfigs.
This change was tested on a proprietary board using the STM32U5 series
which exposes the CAN pins of the SOC using a transciever on a live CAN
bus as well as on the nucleo_g474re board from ST in loopback mode.
HSE and PLL1Q tests run and all passed.
PLL2P is not currently supported by the clock drivers for STM32U5, and
as such is currently untested. When this support is added, the driver
should be able to use this clock without issue.
When changes from #42097 are merged this fix should be deprecated in
favor of using the methods outlined there.
Signed-off-by: Peter Maxwell Warasila <madmaxwell@soundcomesout.com>
Set the PCR[MUX] field to kPORT_MuxAsGpio as part of configuring a GPIO
pin. This removes the need to explicitly call pinmux_pin_set() in board
code.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Adds a log backend that maintains a ringbuffer in coordination
with cAVS HDA.
The DMA channel is expected to be given some time after the logger
starts so a seperate step to initialize the dma channel is required.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Do not default FLASH_MCUX_FLEXSPI_XIP to enabled when code is not
located in flash, this will cause issues if code is executing from ITCM,
as the zephyr_code_relocate macro will relocate the flash driver code
into itcm, and overwrite the zephyr image.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Do not query SIM card parameters if the SIM
card is not present.
This shortens the driver initialization time
significantly if a SIM card is not present.
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
Store sensor trigger structure reference provided on `trigger_set`, and
pass reference back to client when trigger callback is invoked.
This will enable client to use `CONTAINER_OF()` inside its trigger
callback code.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Add support for missing EHL SKUs. The information about SKUs is
already public and available in Linux kernel:
https://github.com/torvalds/linux/blob/
38f80f42147ff658aff218edb0a88c37e58bf44f/drivers/edac/
igen6_edac.c#L197-L208
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add optional PINCTRL support to the Microchip XEC PS2 driver
shared between MEC15xx and MEC172x families.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Update the Microchip XEC PS2 driver to support MEC172x.
NOTE: MEC15xx has two PS2 controllers and
MEC172x has one.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
since the flexspi driver interacts with the flash device, storing
device data in flash can cause RWW hazards when running in XIP mode.
Move all device data to RAM to limit these RWW hazards.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
since the flexspi driver interacts with the flash device, storing
device data in flash can cause RWW hazards when running in XIP mode.
Move all device data to RAM to limit these RWW hazards.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Move all device data to RAM. Since the flexspi driver accesses the
flash device that is being used for XIP, various RWW hazards can occur
if the flexspi driver is interacting with the flash device, while
running in XIP mode.
Fixes#45182
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Comparator will monitor signal though ADC channel, based on
user configuration, callback will be triggered.
This will enable comparator functionality for nuvoton MCU utilizing its
ADC threshold detection feature. Implementation is exported through
sensor trigger API. Use of CONFIG_ADC_CMP_NPCX is required.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Refactor code so that an unused variable 'adc' warning
is not generated when building for CONFIG_SOC_SERIES_STM32G4X
and not using adc1 or adc5.
Signed-off-by: Sam Hurst <sbh1187@gmail.com>
