move DT_DRV_COMPAT to bmp388.h. so that can be decide which
interface to use.
define struct bmp388_bus_io interface bmp388_i2c.c and bmp388_spi.c.
redefined bus operation interface in bmp388.c, this allow the driver
to decide which interface to use during construction
Signed-off-by: Weiwei Guo <guoweiwei@syriusrobotics.com>
Fixes the bmp388 sensor driver to store the user-supplied sensor
trigger as a pointer rather than a copy. This enables the trigger
handler to use CONTAINER_OF to retrieve a context pointer when the
trigger is embedded in a larger struct.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
`spi_is_ready` function is being deprecated in favor of
`spi_is_ready_dt` so let's replace the old usage in the tree.
Signed-off-by: Bartosz Bilas <bartosz.bilas@hotmail.com>
Refactors all sensor drivers to use SENSOR_DEVICE_DT_INST_DEFINE, which
is a sensor-specific variant of DEVICE_DT_INST_DEFINE that provides a
common place to instantiate additional data structures for the future
sensor subsystem and/or sensor driver stats.
This approach was inspired by I2C_DEVICE_DT_INST_DEFINE to streamline
adding I2C stats support across all I2C drivers.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
This change in pattern is meant to address a misconfiguration issue
that can occur for sensors that support being on multiple busses
like I2C & SPI.
For example, you can have a configuration in which such a sensor is
on the I2C bus in the devicetree and the sensor is enabled. However
the application configuration enables CONFIG_SPI=y and CONFIG_I2C=n
and this will cause the sensor driver to be built by default, however
since we don't have the I2C bus enabled the driver will not compile
correctly.
Previously we had been adding to board Kconfig.defconfig something
like:
config I2C
default y if SENSOR
This pattern doesn't scale well and may differ from what an application
specific need/use is.
So instead move to a pattern in which we leave the default enablement
up to the devicetree "status" property for the sensor. We then have
the Kconfig move from 'depends on <BUS>' to 'select <BUS>' and in
the case of drivers that support multiple busses we have the Kconfig
be: 'select <BUS> if $(dt_compat_on_bus,$(<DT_COMPAT>),<BUS>) for
each bus type the sensor supports.
This removes the need to add Kconfig logic to each board and enables
the bus subsystem and bus controller driver if the sensor requires
it by default in the build system.
Fixes: #48518
Signed-off-by: Kumar Gala <galak@kernel.org>
Update sensor drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol
to expose the driver and enable it by default based on devicetree.
Signed-off-by: Kumar Gala <galak@kernel.org>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Stop using redundant DEV_DATA/DEV_CFG macros and use dev->data and
dev->config instead.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In order to align with macros used to obtain a device reference (e.g.
DEVICE_DT_GET), align the PM macros to use "GET" instead of "REF". This
change should have low impact since no official release has gone out yet
with the "REF" macros.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The device PM subsystem _depends_ on device, not vice-versa. Devices
only hold a reference to struct pm_device now, and initialize this
reference with the value provided in Z_DEVICE_DEFINE. This requirement
can be solved with a forward struct declaration, meaning there is no
need to include device PM headers.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Port some drivers to the recently introduced macros to showcase its
usage and be able to do some initial testing (nRF52840).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The PM callback is no longer referenced as "pm_control" but
"pm_action_cb", so reflect this new naming on the callbacks.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Some GPIO related calls were not being checked for error.
This patch fixes coverity issue 236647.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Instead of passing target states, use actions for device PM control.
Actions represent better the meaning of the callback argument.
Furthermore, they are more future proof as they can be suitable for
other PM actions that have no direct mapping to a state. If we compare
with Linux, we could have a multi-stage suspend/resume. Such scenario
would not have a good mapping when using target states.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
According to the documentation the OFF state has to be used when the
devices is fully turned off, ie, power removed. Most drivers were using
a sort of fall-through for all non-active states, leading to behaviors
not following the specifications.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
- Return -ENOTSUP if the requested state is not supported
- Remove redundant "noop style" functions.
- Use switch everywhere to handle requested state (not necessary in all
drivers, but better take off with consistency in place after current
changes).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The verb tense for the suspended state was not consistent with other
states. The likely reason: state was being used as a command/action.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The device PM control function will only be called if the requested
state is different from the current one. A significant amount of drivers
were checking for state changes, now unnecessary. This patch removes all
this redundant logic.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Since the state is no longer modified by the device PM callback, just
use the state value.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The callback is now invoked to set the device PM state in all cases, so
the usage of ctrl_command is redundant.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The device PM subsystem already holds the device state, so there is no
need to keep duplicates inside the device. The pm_device_state_get has
been refactored to just return the device state. Note that this is still
not safe, but the same applied to the previous implementation. This
problem will be addressed later.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The following device busy APIs:
- device_busy_set()
- device_busy_clear()
- device_busy_check()
- device_any_busy_check()
were used for device PM, so they have been moved to the pm subsystem.
This means they are now prefixed with `pm_` and are defined in
`pm/device.h`.
If device PM is not enabled dummy functions are now provided that do
nothing or return `-ENOSYS`, meaning that the functionality is not
available.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The callback is not used anymore, so just delete it from the pm_control
callback signature.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
the device PM callback is not used anymore by the device PM subsystem,
so remove it from all drivers/tests using it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Move all PM_DEVICE_STATE_* definitions to an enum. The
PM_DEVICE_STATE_SET and PM_DEVICE_STATE_GET definitions have been kept
out of the enum since they do not represent any state. However, their
name has not been changed since they will be removed soon.
All drivers and tests have been adjusted accordingly.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
For some reason a few drivers were not converted to the new device PM
callback signature. The reason may be because the device PM part is
compiled only when CONFIG_PM_DEVICE=y, a condition not enabled in CI by
default.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
