Fixes sensor drivers to consistently return -ENOTSUP when an unsupported
channel argument is passed to the sensor_channel_get function.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
`spi_is_ready` function is being deprecated in favor of
`spi_is_ready_dt` so let's replace the old usage in the tree.
Signed-off-by: Bartosz Bilas <bartosz.bilas@hotmail.com>
Refactors all sensor drivers to use SENSOR_DEVICE_DT_INST_DEFINE, which
is a sensor-specific variant of DEVICE_DT_INST_DEFINE that provides a
common place to instantiate additional data structures for the future
sensor subsystem and/or sensor driver stats.
This approach was inspired by I2C_DEVICE_DT_INST_DEFINE to streamline
adding I2C stats support across all I2C drivers.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
According to the BME680 datasheet, only the spi_mem_page bit can be
changed in its 8-bit register. Therefore we shouldn't just write 0s
to the remaining bits, but update the register content in read-modify-write
fashion instead.
Rework the bme680_set_mem_page(), bme680_init() and register-access
macros.
Signed-off-by: Jan Kuliga <jtkuliga@gmail.com>
This change in pattern is meant to address a misconfiguration issue
that can occur for sensors that support being on multiple busses
like I2C & SPI.
For example, you can have a configuration in which such a sensor is
on the I2C bus in the devicetree and the sensor is enabled. However
the application configuration enables CONFIG_SPI=y and CONFIG_I2C=n
and this will cause the sensor driver to be built by default, however
since we don't have the I2C bus enabled the driver will not compile
correctly.
Previously we had been adding to board Kconfig.defconfig something
like:
config I2C
default y if SENSOR
This pattern doesn't scale well and may differ from what an application
specific need/use is.
So instead move to a pattern in which we leave the default enablement
up to the devicetree "status" property for the sensor. We then have
the Kconfig move from 'depends on <BUS>' to 'select <BUS>' and in
the case of drivers that support multiple busses we have the Kconfig
be: 'select <BUS> if $(dt_compat_on_bus,$(<DT_COMPAT>),<BUS>) for
each bus type the sensor supports.
This removes the need to add Kconfig logic to each board and enables
the bus subsystem and bus controller driver if the sensor requires
it by default in the build system.
Fixes: #48518
Signed-off-by: Kumar Gala <galak@kernel.org>
Update sensor drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol
to expose the driver and enable it by default based on devicetree.
Signed-off-by: Kumar Gala <galak@kernel.org>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Consolidate the initialization routines and change the include guard to
conform with the coding guidelines as a preparation for the following
commits which add support for the SPI interface.
Signed-off-by: Leonard Pollak <leonardp@tr-host.de>
This fixes the constant for the mem page and replaces a
magic number with the already defined `BME680_LEN_COEFF2` constant.
Signed-off-by: Leonard Pollak <leonardp@tr-host.de>
Some drivers explicitely casted data/config from void * to the
corresponding type. However, this is unnecessary and, in many drivers it
has been misused to drop const qualifier (refer to previous commits).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In drivers/sensor/CMakeLists.txt, we have various lines like this:
add_subdirectory_ifdef(CONFIG_FOO foo)
Then drivers/sensor/foo/CMakeLists.txt says:
zephyr_library()
zephyr_library_sources_ifdef(CONFIG_FOO foo.c)
This is redundant; the foo/CMakeLists.txt won't be added to the build
system unless CONFIG_FOO=y in the first place, so there's no need for
extra boilerplate testing it again.
Remove all these unnecessary instances in each sensor driver's
CMakeLists.txt using this pattern:
zephyr_library()
zephyr_library_sources(foo.c)
In a couple of places, the '.c' extension is missing. Add them in for
consistency when that happens.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
A single menu within an if like
if FOO
menu "blah"
...
endmenu
endif
can be replaced with
menu "blah"
depends on FOO
...
endmenu
Fix up all existing instances.
Also remove redundant extra menus underneath 'menuconfig' symbols.
'menuconfig' already creates a menu.
Also remove the menu in arch/arm/core/aarch32/Kconfig around the
"Floating point ABI" choice. The choice depends on FLOAT, which depends
on CPU_HAS_CPU, so remove the 'depends on CPU_HAS_FPU' too.
Piggyback removing a redundant 'default n' for BME280.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use LOG_DBG instead of LOG_ERR when BME680 chip is detected
and its ID verified successfully.
Signed-off-by: Jan Tore Guggedal <jantore.guggedal@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Clean up space errors and use a consistent style throughout the Kconfig
files. This makes reading the Kconfig files more distraction-free, helps
with grepping, and encourages the same style getting copied around
everywhere (meaning another pass hopefully won't be needed).
Go for the most common style:
- Indent properties with a single tab, including for choices.
Properties on choices work exactly the same syntactically as
properties on symbols, so not sure how the no-indentation thing
happened.
- Indent help texts with a tab followed by two spaces
- Put a space between 'config' and the symbol name, not a tab. This
also helps when grepping for definitions.
- Do '# A comment' instead of '#A comment'
I tweaked Kconfiglib a bit to find most of the stuff.
Some help texts were reflowed to 79 columns with 'gq' in Vim as well,
though not all, because I was afraid I'd accidentally mess up
formatting.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
move misc/byteorder.h to sys/byteorder.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move sensor.h to drivers/sensor.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move i2c.h to drivers/i2c.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
