Minor optimization to use a local variable instead of a
deferencing of a struct member.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The nRF52840 DK board target, so far known as nrf52840_pca10056,
is renamed to nrf52840dk_nrf52840.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Update the ticks_current value on last stopped ticker
instance, so that when a new ticker instance is started
the anchor ticks calculation uses the correct current tick
with respect to supplied anchor ticks.
Fixes#23805.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Remove use of k_cpu_idle in controller, and refactor the
implementation used to start, wait and stop clocks needed
by the controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
We rename the nRF51 Dev Kit board target (nrf51_pca10028)
to nrf51dk_nrf51422. We update all associated references
in the supportive documentation and all nRF51-related
cofigurations and overlay files in the samples and tests
in the tree.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Fix directed advertising from privacy disabled peer. In this case we
need to have the local IRK in the controllers resolving list in order to
have the controller resolve the initiator address of the directed
advertising pdu (ADV_DIR_IND).
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix directed advertiser using the wrong local IRK when doing directed
advertising when the identity of the advertiser is not the default
identity.
This is only an issue for the directed advertiser because it is only
for the directed advertiser that we use the controllers local IRK
to generate the Advertisers RPA.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add header definition for bt_read_static_addr function. Declaring it
without a header definition will not give any compilation error when
function definition changes.
Refactor nRF SoC specific code into nRF specific source files and
provide weak definitions when these are not implemented. This will make
it easier to add handlers per vendor.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
When using BT_LE_ADV_NCONN_NAME then the advertising name will not be
included in the advertising data. This is because the host always puts
the device name in the scan response. But since the scan data was
otherwise empty the advertising type was set to ADV_NONCONN_IND.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Splits PB-ADV and PB-GATT into separate modules with a common interface
to modularize prov.c.
Additional trivial fixes from testing:
- Reduces warnings for normal occurances like repeated packets.
- Makes link ack a non-reliable packet to prevent it from being repeated
until prov invite.
- Provisioner does not send link fail, but closes the link (as per spec
section 5.4.4). This prevents lingering zombie links on both sides.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
This reverts commit 8739517107.
Pull Request #23437 was merged by mistake with an invalid manifest.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Allocates segmented message buffers as slabs in a common pool for RX and
TX. This reduces memory requirements for both TX and RX, as TX messages
can be stored without the network and advertising buffer overhead, and
RX can use only the slabs it needs, instead of allocating a full size
segmented message. This approach also removes the need for decrypting
the segments for each retransmission, reducing overall processing load.
Slab based segmentation for tx also introduces queuing of segmented
messages, which allows the application layer to send multiple messages
to the same destination without violating Bluetooth Mesh specification
v1.0.1, section 3.6.4.1. This mechanism is provided through a flag that
blocks segmented messages to a destination which a message is already
being sent to until the previous message finishes.
This changes the SDU size configuration to a symmetrical
RX_SEG_MAX/TX_SEG_MAX pair of configurations, plus a new segment pool
side configuration. It also removes the binding between the TX_SEG_MAX
config and the advertising buffers, reducing the minimum advertising
buffer count from 6 to 3.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
The Friend queue uses the message SeqAuth to determine whether the
message is already in the queue. To facilitate this, the SeqAuth is
passed around as a pointer throughout the transport modules. In the
bt_mesh_ctl_send functions, this parameter is also exposed in the API,
but the internal usage is inconsistent and buggy. Also, no one actually
uses this parameter.
- Removes seq_auth param from bt_mesh_ctl_send, instead passing NULL
directly to the friend module, to enforce its addition to the queue.
- Makes the seq_auth pointer const throughout the friend module.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
A bug in the PKT_US resulted in wrong calculations for the 2M phy.
Fixes the bug, verified on EBQ.
Also adds some defines for improved readability.
Fixes#23482
Signed-off-by: Andries Kruithof <Andries.Kruithof@nordicsemi.no>
Fix LLL implementation handling preemption of currently
active radio event with densely scheduled events in the
pipeline.
Preempt timeout was stopped without consideration to there
being more queued events in the pipeline. Also, added
chaining of preemption timeouts one after the other expiry
so as to preempt currently active events by the densely
scheduled events in the pipeline.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix regression in handling invalid packet sequence in the
first packet in a connection.
This relates to commit 62c1e1a52b ("Bluetooth: controller:
split: Fix assert on invalid packet sequence")
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix regression in handling tx pool corruption in relation to
commit 7a3e29af06 ("Bluetooth: controller: legacy: Fix Tx
pool corruption").
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix response to unexpected LL_FEATURE_RSP for the case that
BT_CTLR_SLAVE_FEAT_REQ is disabled. Fixes LL/PAC/SLA/BV-01 for such a
configuration.
Signed-off-by: Wolfgang Puffitsch <wopu@demant.com>
Fixes#23485
When we create a GATT table dynamically, we also create a hash
identifying this table. This hash can be stored in persistent memory and
we can thus determine after recreating the GATT table whether the
services have changed or not from before the reboot.
When these hashes are identical, it implies that the table has not
changed, wherefore a service changed indication should not be sent to
any bonded clients. The method for achieving this was to remove the
gatt_sc.work entry from the work queue. This work queue entry was to
send an indication to the clients when the table had been allocated.
If the final entry then caused the hashes to match, the indication
would be cancelled.
On unit testing this behaviour in simulation and in practice, we found
that the indication was sent nonetheless, and the issue was located to
be tied to the SERVICE_RANGE_CHANGED flag which is set when the services
are changed and is cleared when the indications are being sent out.
It was the job of the work queue entry to clear this flag, and as the
entry was never serviced, the flag was never cleared, and when
sc_commit() is called at the end of the process, it believes that there
is a new service change pending and therefore starts the job over, thus
creating a redundant indication to the clients.
This commit fixes the issue by clearing the flag when the work entry
is removed due to a hash match. This has been unittested in a live
environment, in a simulation environment, and sanitycheck has been run
on it.
Signed-off-by: Dan Erichsen <daee@demant.com>
The commit e85dd8af5d changed the way the BT_ECC Kconfig option
is enabled, however it got the dependency wrong. The dependency should
only look at BT_SMP_OOB_LEGACY_PAIR_ONLY if BT_SMP was also enable.
This broke e.g. the build of the mesh_demo app for the BBC
micro:bit since the memory consumption jumped up by roughly 2k.
This patch fixes the issue, and in the same go makes the Mesh handling
consistent by also using a conditional default rather than select.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Allow to get local OOB data while advertiser, scanner or whitelist
initiator is active. If direct initiator is active or the advertiser
is using the random address as a random static identity address then
the function will return error.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
When OOB callbacks are present it is possible to achieve authenticated
pairing without having the remote OOB data present. Using OOB with
LE Secure Connection only one side of the pairing procedure is required
to have the OOB data present. If we have given the remote our OOB data
then pairing can proceed.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Update LLCP handling during PHY update and Data Length update to not
start the LL control procedure if the remote has already indicated that
the procedure is not supported.
This fulfills the following requirement from the BT Core Specification
(Core_v5.2, Vol 6, Part B, Section 4.6):
Except where explicitly stated elsewhere in this specification, if the
peer Link Layer has indicated either during a feature exchange procedure
or by responding with an LL_UNKNOWN_RSP PDU that it does not support a
procedure, then the Link Layer shall not use that procedure.
Re-use the connection parameter request handling for PHY and
data length update procedures.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix missing first connection event due to first connection
event ticks_slot overlapping with the initiator window
ticks_slot.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add ticker_stop_abs interface, similar functionality as to
ticker_stop interface to stop a running ticker but with a
supplied absolute tick reference value.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added the functions to turn on/off the radio from LLL.
Added WAKE_IRQ to start radio after it's out of DSM.
Signed-off-by: George Stefan <george.stefan@nxp.com>
Added the functions to turn on/off the radio.
Deep Sleep Mode (DSM)
Signed-off-by: Ionut Ursescu <ionut.ursescu@nxp.com>
Signed-off-by: George Stefan <george.stefan@nxp.com>
This patch adds the selection of the necessary CONFIG_*
options for allowing the use of the 2Mbps BLE PHY on
VEGA platform.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
The radio on the VEGA platform supports both 1Mbps, as well
as 2Mbps BLE PHYs. It does not support coded BLE PHY. This patch
adds the necessary callback, as well as timings to enable the 2 Mbps
PHY support in the SW LL HAL for VEGA.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Add command to input the legacy pairing OOB TK during the pairing
procedure.
Fixed shell build with CONFIG_BT_SMP_OOB_LEGACY_PAIR_ONLY defined.
Print error code when passkey input failed.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Added CONFIG_BT_SMP_OOB_LEGACY_PAIR_ONLY option that completely disables
all legacy and SC pairing modes(except for Out of Band) and frees the
memory previously used by these.
Added CONFIG_BT_SMP_DISABLE_LEGACY_JW_PASSKEY option that force rejects
pair requests that lead to legacy Just Works or Passkey pairing.
Signed-off-by: Iván Morales <ivan98ams@gmail.com>
Changes the behavior of the message cache to optimize for cache
capacity. Previously, the message cache's primary function was to avoid
decrypting messages multiple times, although the cache's main function
in the spec is to avoid message rebroadcasting. Optimizing for minimal
decryption causes us to fill the network cache faster, which in turn
causes more cache misses, potentially outweighing the advantage.
Now stores src + seq in message cache instead of field hash value. This
cuts cache size in two, while including more of the sequence number than
before.
Adds messages to the cache only after the packet is successfully
decrypted. This reduces noise in the cache, and ensures that no
invalid deobfuscations are added.
Additionally, this fixes a bug where multiple calls to net_decrypt with
the same packet failed, as the message cache found its own entry from
the previous call.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Refactor old state handling in bt_conn_set_state to use switch statement
instead of if statements.
This will give us warning about enum values not covered.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix connection complete event handling when the local RPA is not valid.
This can happen when the controller was not instructed to use an RPA
address, or the local IRK was set to an all zero IRK.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
In Core v5.2, Vol 6, Part B, Section 4.6.9 it is stated that it is
mandatory to support the PHY procedure if any PHY other than 1M is
supported.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
For the time being this 2M is only selectable for !nRF51 platforms.
Coded PHY is only selectable for nRF platforms supporting Coded PHY.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
According to the Zephyr VS HCI specification:
Only Read_Version_Information and Read_Supported_Commands commands are
mandatory.
Check for supported Read Supported Features command before issuing this
command to the controller.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Make BT_CTLR_OPTIMIZE_FOR_SPEED option so that it is not
user selectable for nRF51x series SoC with encrypted
connections support.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix to return the max tx/rx time back to set default time
after using mandatory minimum PDU length and time while
switching back from Coded PHY to 1M PHY.
Also fixes#23109.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix Data Length Update transmit and receive time calculation
on PHY update procedure completion.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix host resolving the peer identity address in enhanced connection
complete event when the resolving list in the controller is full and
resolution is done in the host.
Move the handling from legacy connection complete into enhanced
connection complete event so that it is done for both connection
complete events.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Implements several changes to the transport layer segmented tx to
improve group message performance:
- Moves retransmit counter to tx context instead of per packet. As every
unacked packet is sent every retransmit, the retransmit counters would
be the same in each segment. This makes it easier to control progress.
- Delays the scheduling of the retransmit until the completion of the
last segment by adding a seg_pending counter. This is essentially the
same as the old behavior, except that the old behavior might retrigger
the sending before all segments are finished if the advertising is
slow.
- Allows the group transmits to stop as soon as all retransmits have
been exhausted, instead of timing out waiting for acks that won't
come. This allows group tx to finish without error.
- Fixes a bug where a failed TX would block IV update.
- Cancels any pending transmissions of acked segments.
- Reduces log level for several common group tx scenarios that aren't
erronous.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
When available, the shell will use the CDB when configuring. This
replaces the default key for configuration and self-provisioning,
ensuring that there aren't multiple key values for the same indexes.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
If the application has used bt_le_oob_get_local to retrieve the OOB
RPA address and OOB authentication information the central role should
use this RPA address for the next RPA timeout period.
The central role always refreshes the RPA address for the initiator,
this will make the OOB information not usable as the peer cannot
recognize the central role since the RPA address is changed.
Check if the initiator can use the address for the duration of the of
remaining RPA period.
Fix central role using the advertiser identity when setting the private
address. The central role should only use the default identity.
Regressions from:
fbe3285bfa
and
4876a8f39a
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix possible NULL dereference in BT_DBG statement when
bt_mesh_friend_get is called before a successful cfg_srv init
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix conditional compilation error when enabling
BT_CTLR_FAST_ENC for central only application builds.
Also added additional compilation to code exclusive to
central or peripheral role.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
