Added a driver to enable the GPT timer on RT1xxx parts to be used
instead of systick as a clock source. The timer is set to run in reset
mode, and uses the low frequency 32kHz oscillator for power savings
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add support for the 8 channels TCA9548A I2C mux.
Added a new binding ti,tca9548a binding inheriting
properties from ti,tca954x-base and defining its own compatibles fields.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Add an optional "reset-gpios" phandle-array
field to the driver common yaml.
The reset GPIO channel and pin can be defined
in device tree as a node property.
The driver then deassert the reset signal at mux
initialization if a "reset-gpios" has been specified.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Prepare the driver to upcoming support of more mux references.
Rename all TCA9546A related files to TCA954x.
Keep ti,tca9546a and ti,tca9546a-channel compatible
for backward compatibility reasons.
New tca954x-base binding embedding common properties,
tca9546a binding inherits from it and define its own compatibles fields.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Make use of the i2c and spi DT APIs introduced in
2946a535 and c894ad12 that get i2c_dt_spec and spi_dt_spec
as input arguments.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The warning below appears once -Waddress-of-packed-mem is enabled:
/__w/zephyr/zephyr/drivers/sensor/bmi160/bmi160.c: In function
bmi160_gyr_channel_get:
/__w/zephyr/zephyr/drivers/sensor/bmi160/bmi160.c:795:23: error: taking
address of packed member of struct <anonymous> may result in an
unaligned pointer value [-Werror=address-of-packed-member]
795 | data->sample.gyr, val);
| ~~~~~~~~~~~~^~~~
/__w/zephyr/zephyr/drivers/sensor/bmi160/bmi160.c: In function
bmi160_acc_channel_get:
/__w/zephyr/zephyr/drivers/sensor/bmi160/bmi160.c:807:23: error: taking
address of packed member of struct <anonymous> may result in an
unaligned pointer value [-Werror=address-of-packed-member]
807 | data->sample.acc, val);
| ~~~~~~~~~~~~^~~~
To avoid the warning, make the struct non-packed, since it is not
necessary in this case given that a union already guarantees that the
pointer to the union points to each member of the union equally..
More info in #16587.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The warning below appears once -Waddress-of-packed-mem is enabled:
/__w/zephyr/zephyr/drivers/gpio/gpio_sx1509b.c: In function
'port_write':
/__w/zephyr/zephyr/drivers/gpio/gpio_sx1509b.c:456:19: error: taking
address of packed member of 'struct sx1509b_pin_state' may result in an
unaligned pointer value [-Werror=address-of-packed-member]
456 | uint16_t *outp = &drv_data->pin_state.data;
To avoid the warning, use an intermediate void * variable.
More info in #16587.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add bindings for SDL based display controller.
Rework SDL based display controller driver to obtain
configuration from devicetree. Remove unnecessary casts,
add multi-instance support.
Add display controller node and chosen property
to native_posix devicetree.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
ssd16xx driver is not well designed and does not pass configuration
via device->config but via struct ssd16xx_data, this was not taken
into account in the commit 4d6d50e2bc
("display: ssd16xx: convert to spi_dt_spec").
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
this allows using a pin numbering scheme as per Espressif's
documentation and HAL usage, where pin counting does not wrap
up when reaching a given number.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Voltage scaling computation should be done in multiple cases.
Add a function that takes into account all cases.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Deprecate the use of CAN-specific error return values and replace them
with standard errno values.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The init responsibility moves to the drivers themselves. The npcx itim
initialize doesn't work now. This adds timer initialization for npcx
itim to fix it.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
The original code erroneously used:
uint16_t *val;
sizeof val
instead of:
sizeof *val;
This commit fixes this problem and removes an unnecessary
buffer from the stack
Signed-off-by: Pete Dietl <petedietl@gmail.com>
SDK 2.10 changed the PHY API. These updates are
needed as part of moving to SDK 2.10
1. add phy / mdio ops init
2. update PHY_Read/Write HAL call
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Set pinmux driver to use RTCIO interface for to handle
dedicated IOs pull-up/down configuration.
Without this, some GPIOS won't have pull-up enabled
properly.
Also, current implementation automatically disables
output pin when input pin is set. It also performs the
oppositte. This PR changes it only to enable what is
requested, either input or output.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
irq_line and irq_enabled call is not necessary as the interrupt
allocater enables it during its initialization.
it also adds end packet to all write transmission instead
of only at the end (burst data scenario)
Add check in gpio configuration check to avoid wrong gpio pins
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Driver has dedicated workqueue for IRQ processing.
Submit work to dedicated workqueue intead of system workqueue.
It also fixes driver functionality when NET_TC_TX_COUNT is set to 0.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
STM32H7 has different power supply modes but now Zephyr supports just LDO
and direct SMPS. This commit introduses POWER_SUPPLY_CHOICE configuration
parameter and add support for missed power supply modes.
Signed-off-by: Gennady Kovalev <gik@bigur.com>
Fixes#40730.
A dead lock could happen if 2 threads with differents priorities use
poll_out. In fact, the lock data->tx_lock could be lock by a thread with
lower priority and then a thread with higher priority can't take the
lock. There was a race condition here:
/* Wait for TXE flag to be raised */
while (1) {
if (atomic_cas(&data->tx_lock, 0, 1)) {
/* !!!!!!!! RACE CONDITION !!!!!!!!!!!!!!
if (LL_USART_IsActiveFlag_TXE(UartInstance)) {
break;
}
atomic_set(&data->tx_lock, 0);
}
}
To fix race condition, the interrupts are locked in poll_out.
Signed-off-by: Julien D'ascenzio <julien.dascenzio@paratronic.fr>
Refactor the mcp230xx driver to generically also support
SPI IO expanders, renaming it to mcp23xxx in the process.
Signed-off-by: Peter Johanson <peter@peterjohanson.com>
Add driver for MEC172x QMSPI with local DMA(LDMA). The driver
support SPI asynchronous operation.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
DMA controller is enabled and tested for cortex M7 core. The M7 core was
tested on the loop and channel link transfer tests.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This commit adds support for editing the voltage levels on the buck
regulators on the PCA9420 PMIC
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This commit adds a generic i2c regulator driver, and enables the NXP
PCA9420 PMIC IC using this driver. The regulator driver also exposes an
additional API in include/drivers/regulator/consumer.h, which allows
drivers to implement support for adjusting voltage levels and current
limits, if their device supports it.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
the RT685 contains an additional flexcomm peripheral, that supports
only I2C. This commit adds this peripheral to the device tree,
and enables pins and clocks for flexcomm15.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Catch up on the CAN driver API argument naming changes:
- Unify naming of callback function pointers as "callback".
- Unify naming of user-specified callback function arguments as
"user_data".
- Instances and pointers to struct zcan_frame are named "frame",
not "msg", to avoid confusion with the CAN message queue support.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This commit adds Xen consoleio serial driver. It is needed to receive
kernel messages from Zephyr in case it runs as Xen privileged domain
(Dom0). There is no console ring buffer for such domain, so regular
uart_hvc_xen driver can not be used (privileged domain input/output
are possible only through consoleio interface).
Signed-off-by: Dmytro Firsov <dmytro_firsov@epam.com>
This commit adds support of interrupt-driven API for UART-like Xen PV
console driver. It is implemented via Xen event channels. It allows to
send and receive data by chunks (not single symbols) and without
polling.
Signed-off-by: Dmytro Firsov <dmytro_firsov@epam.com>
This commit adds support of Xen Enlighten page and initial support for
Xen event channels. It is needed for future Xen PV drivers
implementation.
Now enlighten page is mapped to the prepared memory area on
PRE_KERNEL_1 stage. In case of success event channel logic gets
inited and can be used ASAP after Zephyr start. Current implementation
allows to use only pre-defined event channels (PV console/XenBus) and
works only in single CPU mode (without VCPUOP_register_vcpu_info).
Event channel allocation will be implemented in future versions.
Signed-off-by: Dmytro Firsov <dmytro_firsov@epam.com>
In #40140, all on-chip gpios where made to use `CONFIG_GPIO_INIT_PRIORITY`.
The lmp90xxx and sx1509b are off-chip gpios. This commit reverts those
changes for these two devices.
Signed-off-by: Ryan McClelland <ryanmcclelland@fb.com>
Adds a driver using the SNVS high power and optionally low power
RTC instances. A device specific function `mcux_snvs_rtc_set` is
provided to update the current counter value.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Update the SPI context during all transceive functions. This fixes a
deadlock where SPI transactions failed to give back the semaphore.
Verified on NPCX9 based Chromebook.
Signed-off-by: Keith Short <keithshort@google.com>
The internal functions of this driver needed either `device *`
or `st7789v_data *` as argument. Standardize to
using `device *`.
Signed-off-by: Casper Meijn <casper@meijn.net>
RT11xx USDHC lacks some watermarking features that RT10xx SOCs include.
Place #ifdef guards around these features.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
