Add wsen_pads_2511020213301 driver with
the corrected name and compatibility with
the hal update as well as added new features.
Signed-off-by: Wajdi ELMuhtadi <wajdi.elmuhtadi@we-online.com>
Add wsen_tids_2521020222501 driver with
the corrected name and compatibility with
the hal update as well as added new features.
Signed-off-by: Wajdi ELMuhtadi <wajdi.elmuhtadi@we-online.com>
The TMP435 is a remote temperature sensor monitor
with a built-in local temperature sensor.
Signed-off-by: Jaakko Rautiainen <jaakko.rautiainen@bittium.com>
Add wsen_pdus_25131308XXXXX driver with
the corrected name and compatibility with
the hal update as well as added new features..
Signed-off-by: Wajdi ELMuhtadi <wajdi.elmuhtadi@we-online.com>
Fixes issue introduced in #76460
The previous code attempted to detect whether TMAG5273 or TMAG3001 was
connected based on DEVICE ID register. This doesn't work as the bits that
denote the version on one part are undefined on the other part, and cannot
be relied on to be zero.
This commit adds a TMAG3001 compatible which (for now) is just derived from
the TMAG5273 compatible. This allows TMAG3001 to be specified directly in
the DT. The driver code is updated to support both compatibles.
Signed-off-by: Yiding Jia <yiding.jia@gmail.com>
The LIS2DUXS12 is a smart, digital, 3-axis linear accelerometer whose
MEMS and ASIC have been expressly designed to combine the lowest current
consumption possible with features such as always-on antialiasing
filtering, a finite state machine (FSM) and machine learning core (MLC)
with adaptive self-configuration (ASC), and an analog hub / Qvar sensing
channel.
(https://www.st.com/en/mems-and-sensors/lis2duxs12.html)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add device definitions in dt to test drivers that handle
multiple "compatible"s by a single driver.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Add sensor driver for npm2100 pmic.
This pmic performs measurements of battery voltage, regulator voltage
and die temperature.
Configurable pmic attributes are also organized under this driver.
Signed-off-by: Audun Korneliussen <audun.korneliussen@nordicsemi.no>
Add support for setting the sample frequency via `attr_set` and the
output data rate from device tree source.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Don't duplicate the test's output running it on `native_sim` after
`LOG_BACKEND_NATIVE_POSIX` was enabled by default (bd9836be8c)
Signed-off-by: Dmitrii Golovanov <dmitrii.golovanov@intel.com>
The ILPS22QS is an ultra-compact piezoresistive absolute pressure sensor
which functions as a digital output barometer, supporting dual full-scale
up to user- selectable 4060 hPa. The device delivers ultra-low pressure
noise with very low power consumption and operates over an extended
temperature range from -40 °C to +105 °C.
(https://www.st.com/en/mems-and-sensors/ilps22qs.html)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add wsen_hids_2525020210002 driver with
the corrected name and compatibility with
the hal update as well as added new features.
Signed-off-by: Wajdi ELMuhtadi <wajdi.elmuhtadi@we-online.com>
Add support for Bosch bmp390 sensor, the drop in replacement for the
bmp388 with same register but different chip-id. This patch make use
of "bosch_bmp390" or "bosch_bmp388" and set the specific chip-id in a
data->chip-id variable, which then used to check against the register
value.
Additional, manual shift operation had been replaced with ENDIAN safe
macros and calibration values with target variable of int16_t add a
cast for it.
bmp388_spi: read register implementation wrong, fixed it.
tx-buffer must be <addr><dummy><dummy> in order to receive the
register value. Read registers in burst mode and have rx and tx
buffer same spi_buf to avoid clock stop and delay with nrf5.
Signed-off-by: Chris Ruehl <chris@gtsys.com.hk>
Use EXTRA_CONF_FILE in sample yaml files,
that replaced deprecated OVERLAY_CONFIG
since the Zephyr v3.4 release.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Fixed incorrect I2C register definitions in the test file
tests/drivers/build_all/sensor/i2c.dtsi.
Signed-off-by: Paweł Czaplewski <pawel.czaplewski@arrow.com>
TI tmp1075 driver implemented based on tmp108 driver.
The driver initializes the sensor based on the DTS.
Added tmp1075 example overlay file to thermometer sample.
All you need to do to use the sensor is to connect the I2C and
optionally interrupt line.
To see default DTS configuration option inspect `ti,tmp1075.yaml`
bindings file and sensor spec.
Signed-off-by: Paweł Czaplewski <pawel.czaplewski@arrow.com>
Change the unit of the sense resistor in the devicetree binding from
micro-ohms to milli-ohms. This is done for three reasons.
Firstly, the maximum value resistor that can currently be represented
is 4.2 kOhms, due to the limitation of devicetree properties to 32 bits.
Secondly, storing the resistance at such a high resolution makes
overflows much more likely when the desired output unit is micro-amps,
not milli-amps.
Finally, micro-ohms, are an unnecessarily precise unit for the purpose
of these calculations, and a resolution that is not realistic to
achieve. The high resistor resolution results in large divisors that
reduce the resolution of outputs. Unlike resistors characterised down to
the micro-ohm, devices wanting to measure micro-amps are actually
realistic.
Signed-off-by: Jordan Yates <jordan@embeint.com>
The following devices enable TRIGGER in a way that is different from the
template definition, so add these settings to sensos_no_default.conf.
- bosch,bmc150
- bosch,bmm150
- bosch,bmp150
- ti,ina230
- we,wsen-itds
- lm77
- st,lsm9ds0-gyro
- ti,tmag5170
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
native_posix is now deprecated.
Building these tests in both native_sim and native_posix does not
improve coverage for the tests or subsystem but doubles CI time.
As anyhow native_posix will be removed all together in
2 releases, let's remove it already for these.
Note: Some drivers tests for which there is native specific driver
which will or may be built differently in native_sim and native_posix
have been left enabled for native_posix
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Use `test_adc` in io-channels to be consistent in whole
tests/drivers/build_all/sensor/adc.dtsi file.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Add all the necessary files to add apds9253 Avago sensor driver.
Sensor available at https://docs.broadcom.com/doc/APDS-9253-001-DS
Signed-off-by: Margherita Milani <margherita.milani@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
