Add a new implementation of a test pattern generator, with the same
architecture as real drivers: split receiver core and
I2C-controlled sub-device, with changes of video format in
"zephyr,emul-imager" leads to different data produced by
"zephyr,emul-rx".
Signed-off-by: Josuah Demangeon <me@josuah.net>
The CSI is an NXP IP and the driver has been very much changed
by NXP, so add NXP copyright to it.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The peer remote device "source_dev" can be retrieved from the
remote-endpoint-label. Direct reference via phandle is not needed.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The peer remote device "sensor_dev" can be retrieved from the
remote-endpoint-label. Direct reference via phandle is not needed.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
Add SMARTDMA video driver. This driver uses the SMARTDMA engine as a
parallel camera interface, which can read QVGA frames from a camera
device. Due to SRAM constraints, the video driver divides the camera
stream into multiple horizontal video buffers as it streams them back to
an application.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add common video interface binding. This binding contains the most
common properties needed to configure an endpoint subnode for data
exchange with other device.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
Introduce driver for ov7670 camera, supporting QCIF,QVGA,CIF, and VGA
resolution in YUV and RGB mode.
Support was verified on the FRDM-MCXN947, using the SmartDMA camera
engine, which is enabled in the following PR:
https://github.com/zephyrproject-rtos/zephyr/pull/72827
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add bindings for NXP MIPI CSI-2 Rx which is a MIPI CSI-2 receiver
connecting a camera sensor to the NXP CSI.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The CSI can connect to either a camera sensor (as on i.MX RT10xx) or
a MIPI CSI-2 receiver (as on i.MX RT11xx). To be generic, change the
naming from sensor to source.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
DTS property attributes are (by default) not required.
Explicitly specifying `required: false` is redundant.
Perhaps a warning to that effect would be useful.
Signed-off-by: Chris Friedt <cfriedt@meta.com>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
Replace sensor_label property in devicetree with just a sensor phandle
property. This is more generic and allows driver to use DEVICE_DT_GET
instead of device_get_binding.
Signed-off-by: Kumar Gala <galak@kernel.org>
This adds the driver for Omnivision OV2640 image sensor.
The driver provides support for 10 different resolutions in range from
160x120 to 1600x1200 in both JPEG and RGB565 pixel formats. There are
also mutliple configuration options, e.g. hflip, vflip, saturation and
brightness control.
Signed-off-by: Robert Szczepanski <rszczepanski@antmicro.com>
This patch adds the driver for Omnivision OV7725
Color CMOS VGA Sensor.
The driver currently provides a simple capture
function, the output format only provides
RGB565,640x480.
Signed-off-by: Frank Li <lgl88911@163.com>
Add any useful information from 'title:' to the 'description:' strings
(e.g. explanations of acronyms), and remove 'title:' as well as any
copy-pasted "this binding gives a ..." boilerplate.
Also clean some description strings up a bit.
Some other things could probably be cleaned up (replacing 'GPIO node'
with 'GPIO controller' on controllers for consistency, for example), but
I kept things close to the original to avoid accidentally messing up.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
With https://github.com/zephyrproject-rtos/zephyr/pull/20185, multi-line
descriptions will be formatted nicely, but using '>' breaks it, because
it removes internal newlines (including between paragraphs).
See https://yaml-multiline.info/.
Replace 'description: >' with 'description: |' to encourage '|'. That'll
prevent '>' from getting copied around and messing up long descriptions.
This will lead to some extra newlines in the output, but it's fine.
Line-wrapping messes up any manual formatting.
The replacement was done with
$ git ls-files 'dts/bindings/*.yaml' | \
xargs sed -i 's/description:\s*>/description: |/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
MT9M114 is a CMOS digital image sensor.
Implement video interface.
Only VGA (640x480) supported for now.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
