Add a interface-name string for the CDC-ACM node, this allow setting a
string that is then set as iInterface, which can then be used downstream
in an udev rule such as:
SUBSYSTEM=="tty", ACTION=="add",
ATTRS{interface}=="my interface descriptor",
SYMLINK+="tty-my-device"
To create known aliases for these ports.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Split the USART driver into separate implementations for Silabs Series 2
and Series 0/1 boards. This change improves maintainability (especially
with the support of pin-ctrl and clock-ctrl on series 2 boards).
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
This commit adds asynchronous mode support to MAX32 UART driver. Each
direction uses a single DMA channel that is assigned in devicetree
configuration.
Asynchronous mode also depends on interrupts to refresh receive
timeouts.
Signed-off-by: Tahsin Mutlugun <Tahsin.Mutlugun@analog.com>
Defined default values for baudrate, parity, stop bits, and data bits.
This removes complexity and obfuscation from the code.
Signed-off-by: Yishai Jaffe <yishai1999@gmail.com>
The Atmel SAM0 SoC enable peripherals clocks in distinct places: PM and
MCLK. The old devices had defined the peripheral clock enable bit at PM.
On the newer devices this was extracted on a dedicated memory section
called Master Clock (MCLK). This change excludes the dedicated bindings
in favor of a generic approach that cover all cases.
Now the clocks properties is complemented by the atmel,assigned-clocks
property. It gives the liberty to user to customize the clock source
from a generic clock or configure the direct connections.
All peripherals drivers were reworked with the newer solution.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
We add a serial UART driver for Microchip MEC5 HAL based chips.
The driver supports polling, interrupts, and runtime configuration
features. Power management will be implemented in a future PR.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
The PL011 driver has already implemented supporting reset device
behavior.
However, the support is incomplete because the `arm,pl011.yaml`,
does not contain a `reset-device.yaml`.
Add include directive to `arm,pl011.yaml` to including
`reset-device.yaml` to complete the support for reset device.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
This is the initial commit to support UART driver for Renesas RZ/G3S.
The driver only implements polling API for minimal support.
Signed-off-by: Nhut Nguyen <nhut.nguyen.kc@renesas.com>
Signed-off-by: Binh Nguyen <binh.nguyen.xw@renesas.com>
Rename "nxp,kinetis-lpuart" compatible to "nxp,lpuart" to remove the
device family from its name.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
This commit adds the usart driver for WCH CH32V003.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
-Update formatting and contents of index.rst for cy8ckit_062s4
-Update formatting and contents of index.rst for cy8ckit_064s0s2_4343w
-Update formatting and contents of index.rst for cy8cproto_062_4343w
-Update formatting and contents of index.rst for cy8cproto_063_ble
-Update formatting and contents of index.rst for xmc45_relax_kit
-Update formatting and contents of index.rst for xmc47_relax_kit
-Change all instances of "PSoC" to "PSOC" for infineon platforms
Signed-off-by: McAtee Maxwell <maxwell.mcatee@infineon.com>
Add property which indicates that UARTE support frame timeout
feature. Property is added to nrf54h20, nrf9280, nrf54l20 and
nrf54l15.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Add information to the device tree if UARTE instance has a HW feature
which is the ENDTX_STOPTX short.
Add this property to all instances in nrf54hl15, nrf54l20, nrf9280
and nrf54h20.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
First commit to support serial driver running on r_sci_uart for Renesas
RA devices.
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
Signed-off-by: Duy Phuong Hoang. Nguyen <duy.nguyen.xa@renesas.com>
... so that a clear devicetree error is reported when the pinctrl-names
property is missing, not a quite cryptic compilation error about an
undeclared PINCTRL_STATE_*_UPPER_TOKEN symbol in pinctrl.h.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This patch adds support for the rx-invert and tx-invert device-tree
properties to the uart_lpc11u6x driver for USARTs 1, 2, 3 and 4.
Note that this feature is not supported by USART 0.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Refactored vendor-specific duplicates of uart tx/rx invert properties
into a common dts file uart-controller-pin-inversion.yaml
Signed-off-by: Anuj Pathak <anuj@croxel.com>
Adding required flag to the current-speed as without this driver
does not compile.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
This change allows to use DTR line driven from external serial port
that when active (low) will prevent UART device from going to sleep.
It will also wake up platform when DTR line becomes active.
DTR line is often activated in serial port connected to host computer
when operating system opens serial device like COMx for Windows
or /dev/ttyACMx /dev/ttyUSBx for Linux based systems.
DTR line (specified in device tree) will be used by WAKEUP and PDC
controllers (via GPIO driver) to handle DTR line changes.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
This change allows to wake up UART from sleep mode when
low level on inactive UART is detected during platform sleep.
Timeout can be specified for each UART separately in device tree.
If one of the UARTs is selected as console sleep timeout is taken
from Kconfig same way other platform configure same functionality
using CONFIG_UART_CONSOLE_INPUT_EXPIRED_TIMEOUT
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Enables usage Bluetooth LE GATT as a serial endpoint to exchange data
using UART APIs. This implementation is compatible with UART Interrupt
Driven APIs and uses the nus-uart device-tree node properties to
configure FIFO buffers for transmitting and receiving. Defining
multiple instances of the driver is possible and it allows implementing
multiple GATT NUS service instances to exchange data as separate serial
endpoints.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
Utilize a code spell-checking tool to scan for and correct spelling errors
in all files within the dts/bindings/retained_mem, rng, serial and spi.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
The meaning of txpo is was a bit confusing, as it's an enumeration
rather than a pad number. This confusion extended to the atsamd21_xpro
board using the wrong pins.
This commit adds ASCII-art tables that explain the meaning of rxpo
and txpo on different platforms.
Signed-off-by: Tom Rothamel <tom@rothamel.us>
This adds a UART driver for the Renesas RZ/T2M
Serial Communication Interface.
The driver implements:
* Polling API,
* Interrupt-driven API.
Signed-off-by: Wojciech Sipak <wsipak@antmicro.com>
Real UARTs usually write 1 to a few bytes at a time through a
latch buffer. Add latch buffer property to binding for
uart_emul and limit fifo_read and fifo_fill to not exceed the
latch buffer.
Signed-off-by: Bjarki Arge Andreasen <bjarkix123@gmail.com>
Adding initial support for Renesas RA UART.
To avoid complicating initial code for supporting the SoC,
I have implemented only the bare minimum for now.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
