In all STM32 dtsi and board dts, update the st,adc-sequencer and the
st,adc-clock-source properties so they are strings.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
fu dts: arm: st: use string instead of enum
Remove all optional, initial CAN sample point properties and rely on the
CAN timing calculations to automatically pick the preferred sample point
location based on the initial bitrate.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add SMBus devices to all SoCs which have either
a st,stm32-i2c-v1 or st,stm32-i2c-v2.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
After porting from h5 to f7 i noticed that not all mcus have
cpu node labels. Added cpu0 node labels to all stm32 dts.
Signed-off-by: Kacper Dalach <dalachowsky@gmail.com>
Update the descriptions for the various CAN devicetree timing properties
specified in Time Quanta (TQ) to make it clear that these, if present, are
only used for the initial timing parameters.
Deprecate the (Re-)Synchronization Jump Width (SJW) devicetree properties
for both arbitration and data phase timing as these are now only used in
combination with the other TQ-based CAN timing properties, which are all
deprecated.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Remove temp-, vref- and vbat-channel from STM32 ADC nodes as it is not
used in the driver anymore.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Rename the STM32 bxCAN driver DTS compatible, Kconfig symbol, and
implementation file to match the naming used in the ST reference manuals.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add the new RCC bindings to the dtsi files.
STM32F373 uses the RCC F1 bindings because the ADC prescaler is the same
on the two series.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Add new vref node to the DTS definitions of supported SoCs.
Extend DTS ADC channel properties where missing.
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
Fixes warnings produced by dtc 1.6 due to missing address-cell
in all arm st exti definition.
Signed-off-by: Christian Spinnler <christian.spinnler@fau.de>
In all STM32 dts, remove all reference to the following properties:
- has-temp-channel
- has-vref-channel
- has-vbat-channel
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Now that we have a binding to define the channel number for temperature
and Vref measurement, update all dtsi to include the information.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Add missing I2C clock sources for STM32F303 & F373.
Add a comment for all STM32F3 I2Cx and for STM32F0 I2C1 that the clock
source should always be defined.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Define SYSCLK as the default I2C source clock for I2C1 on STM32F0x
and all I2Cx on STM32F3x.
On most series, the default I2C clock source (when it exists) is PCLK.
This clock does not exist as I2C clock source on FO & F3 and the default
one is HSI. Since HSI is not necessarily enabled we explicitly set it
to SYSCLK instead.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
We are about to add UART reset during driver initialization. First step
is to add 'resets' property, which provides information about reset
register offset and bit.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
We are about to add timer reset during driver initialization. First step
is to add 'resets' property, which provides information about reset
register offset and bit.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
Reset controller node is necessary to enable support for resetting
peripherials using RCC.
This patch also includes RCC reset registers offsets used by STM32_RESET
macro.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
All supported STM32F3 devices have 4-byte battery-backed RTC registers,
but they have different number of registers:
STM32F303x8 and STM32F334 have 5 registers.
STM32F303xc and STM32F303xe have 16 registers.
STM32F302x8 has 20 registers.
STM32F373 has 32 registers.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
The vref has to be set to 3000mV.
It is the voltage to find on the stm32F3.
is fixed by the platform to be lower or equal to VDDA.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
zephyr.dts:482.21-491.5: Warning (simple_bus_reg): /soc/dietemp: missing
or empty reg/ranges property.
To fix this bug, just move dietemp node outside of soc{}.
Signed-off-by: TLIG Dhaou <dhaou.tlig-ext@st.com>
Add the support of the temperature sensor in the ADC device-tree node of
each stm32 where it is available.
- Check all the ADC of the stm32 mcus where the temp and VrefInt monitoring
is available (based on the Ref Man).
- Check that has-temp-channel; and has-vref-channel; in the corresponding
ADC node of the DTS of each stm32 mcu is correctly set.
- Verify the VTEMP/ VREFINT activation in the in adc_stm32.c for example).
-Add the die-temp node (based on the ref man/ datasheet).
Signed-off-by: TLIG Dhaou <dhaou.tlig-ext@st.com>
The stm32f303x8 SoC is not equipped with spi2 and spi3 peripherals.
Exclude them from the SoC-level devicetree.
Signed-off-by: Jan Kuliga <jtkuliga@gmail.com>
Add clock sources bindings on F0/F3/G0/G4/L0/L1/L4/WB/WL series.
Due to inconsistencies, some common bindings are now split:
F1 -> F0/F1/F3
L4 -> L4/G4/WB
Update .dtsi files when required
In a first step, allowed sources are limited to already supported
clocks: LSI/LSE/HSI/HSE/MSI/PCLK/PLLCLK/SYSCLK
Support for other clocks such as HSI48, SAIXCLK, ... is left for a
next step.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to bring consistency in-tree, migrate all dts code to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to zephyrproject-rtos#45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Make the LSE driving capability configurable for the STM32 series.
Fixes#44737.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
STM32 supports now custom PWM flags, include them by default as done for
the standard flags.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
