Implement lan865x mdio driver to provide interface between lan865x MAC
driver and internal PHY driver phy_microchip_t1s.c. This driver is needed
to support the driver architecture followed.
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Add support for mdio driver for Renesas RA MCU series
This support utilize the r_ether_phy driver in hal renesas
to support mdio write and read function
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
ethernet driver
This driver is capable of supporting basic features
of synposys dwc-xgmac ethernet MAC IP. Basic features
includes,
1. Tx and Rx, multiple Tx and Rx DMA channels, multiple
Tx and Rx queues
2. Check Sum Offloading on Tx and Rx for IPv4, IPv6,
TCP, UDP and ICMP packets
3. 10M/100M/1G speeds, Autonegotiation, Link speed
configuration, Promiscuous mode, Full/Half
duplex configuration
4. Added source files for synopsys dwc xgmac mdio driver.
synopsys dwc xgmac mdio driver fetures includes:
It supports clause 22 of IEEE 802.3 for ethernet PHY devices
management.
5. Extended mdio shell support for dwcxgmac mdio driver.
Signed-off-by: Santosh Male <santosh.male@intel.com>
MDIO is part of the ETH IP, but some phy chip may need a
specific phy driver to set up certain vendor registers enabling
particular features.
Add support for stm32 mdio access.
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
MDIO controller is part of GMAC and it requires GMAC ethernet driver to
initialize first because it will reset the whole GMAC hw block during
initialization. Both C22 and C45 APIs are supported.
Co-authored-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
Do not enable subsystem/driver shell modules by default and stop abusing
CONFIG_SHELL_MINIMAL, which is internal to the shell subsystem, to decide
when to enable a driver shell.
The list of shell modules has grown considerably through the
years. Enabling CONFIG_SHELL for doing e.g. an interactive debug session
leads to a large number of shell modules also being enabled unless
explicitly disabled, which again leads to non-negligible increases in
RAM/ROM usage.
This commit attempts to establish a policy of subsystem/driver shell
modules being disabled by default, requiring the user/application to
explicitly enable only those needed.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add MDIO driver that works through GPIO pins. This driver is
useful when a microcontroller doesn't have MDIO bus or when multiple
separate MDIO buses are required. The driver provides access to
the MDIO bus through GPIO pins for any SoC that has GPIO pin control
available.
Signed-off-by: Aleksandr Senin <al@meshium.net>
Adds MDIO driver. Works via exposed
ADIN2111 functions.
It is possible to access Clause 45 and 22 registers.
Due to MDIO API limitation Clause 45 access
is done using driver specific MDIO functions.
Provides API and functions for PHY driver.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Unify the drivers/*/Kconfig menuconfig title strings to the format
"<class> [(acronym)] [bus] drivers".
Including both the full name of the driver class and an acronym makes
menuconfig more user friendly as some of the acronyms are less well-known
than others. It also improves Kconfig search, both via menuconfig and via
the generated Kconfig documentation.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Introduce NXP S32 NETC External MDIO controller driver. Driver supports
a single instance, as current support is based on NXP S32Z/E SoCs.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
