Change default input format of the shield to RGB 565 to achieve
better frame rate performance.
Remove LV_Z_FLUSH_THREAD as temporary solution for flickering
screen issue when CPU go too high
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Abrobot esp32c3 oled only works with sh1106_compatible display driver.
It does not support 1306 display driver commands.
Its screen resolution is 72x40.
Its screen start position is 30, 12.
Signed-off-by: Rick Cai <wwhheerree@hotmail.com>
Enabling `CONFIG_INPUT_FT5336_INTERRUPT` if the ft5336 node in DT
has `int-gpios` property.
As a result of this change, some boards can eliminate lines that
explicitly configure `CONFIG_INPUT_FT5336_INTERRUPT`.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Unify property names in bindings and overlay, using
hyphens (-) instead of underscores (_) as separators.
Signed-off-by: James Roy <rruuaanng@outlook.com>
Add new test sample.sensor.thermometer_i3c, can't assign the same
platform with i2c, and i3c at the same time.
Support the shield on FRDM_MCXN236 board by I2C and I3C way.
Signed-off-by: Neil Chen <cheng.chen_1@nxp.com>
There are 4 Kconfig names about the "Draw Buffer". Rename 'VBD' to 'VDB'
in Kconfig option 'LV_Z_*VBD*_CUSTOM_SECTION' to make name consistent.
config LV_Z_VDB_ALIGN
int "Rending buffer alignment"
config LV_Z_VBD_CUSTOM_SECTION
bool "Link rendering buffers to custom section"
config LV_Z_DOUBLE_VDB
bool "Use two rendering buffers"
config LV_Z_VDB_SIZE
int "Rendering buffer size"
default 100 if LV_Z_FULL_REFRESH
And the draw buffer definition is now:
static uint8_t buf0[BUFFER_SIZE]
#ifdef CONFIG_LV_Z_VDB_CUSTOM_SECTION
Z_GENERIC_SECTION(.lvgl_buf)
#endif
__aligned(CONFIG_LV_Z_VDB_ALIGN);
Signed-off-by: Haiyue Wang <haiyuewa@163.com>
Completes the PLLi2S configuration for this board based on stm32f411
with a PLLI2S compatible = "st,stm32f411-plli2s-clock";
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Added support for the SPI interface which is availble on the shield
if the jumper configurations are changed.
Signed-off-by: Ian Morris <ian.d.morris@outlook.com>
With recent SDSC bundles, 54H fails the app core boot in case of a
unsupported GPIO in the UICR.
As Wi-Fi SR co-existence on nRF54H20DK is not yet supported, remove this
GPIO for 54H. This will be fixed properly once co-existence is
revisited.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
The documentation incorrectly referred to the Semtech shield as
semtech_sx1271mb1mas. It should be semtech_sx1276mb1mas.
Signed-off-by: Sreeraj Sudhakaran <sreerajsudhakaran@gmail.com>
Shield was enabling some Kconfig options for no reason. Shields do
not need to enable driver classes unconditionally, these are enabled
either by drivers or samples that require them.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add shield definition for the Mikroe ETH 3 Click.
ETH 3 Click is a compact add-on board that contains
LAN9250 SPI Ethernet Controller
Signed-off-by: Mario Paja <mariopaja@hotmail.com>
Configure the TE signal for the rw_rw612_bga board when using the
lcd_par_s035 shield. This signal should be handled on the rising edge in
the default configuration, since the display writes from the MCU are
faster than the panel reads data.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Deprecate BT_CTLR, and add a new HAS_BT_CTLR as a virtual option which
specific users (like BT_LL_SW_SPLIT) select. This also means that we can
remove all places that were forcefully enabling the BT_CTLR option, and
instead we now depend on devicetree to get some local LL HCI driver
enabled which in turn also enables the HAS_BT_CTLR option.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
Added ability for host MCU to perform a hardware reset of the DA14531
contained on the Mikroe BLE Tiny Click.
Signed-off-by: Ian Morris <ian.d.morris@outlook.com>
Use a string for the mipi-mode property over an integer value, as this
significantly improves the readability of the MIPI DBI device binding.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The NXP LCDIC peripheral contains two internal timers, with configurable
periods. These times are used to determine delays within the peripheral,
such as the reset and tearing enable signal delays. Allow these periods
to be set within the devicetree for the peripheral.
Raise the period where required for display drivers that need a value
other than the reset setting
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Use configdefault when enabling LV_COLOR_SWAP_16 within boards and
shield definitions, to avoid OR'ing the dependencies for the Kconfig
symbol. Otherwise, a user manually selecting LV_COLOR_DEPTH will
encounter build errors as LV_COLOR_SWAP_16 may be enabled when
LV_COLOR_DEPTH_16 is not selected
Fixes#81546
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add definition for the Adafruit Adalogger Featherwing. This shield
compatible with the Adafruit Feather family is equipped with an SD card
slot and a PCF8524 RTC.
This work is based on the Adafruit Data Logger shield definition.
Signed-off-by: Philip-Dylan Gleonec <philip-dylan@gleonec.bzh>
Increase target DSI clock frequency for the RT1160, as the DSI
peripheral requires a faster clock to account for the DSI packets that
must be sent outside of video mode frames.
This fix was previously applied for the RT1170, but is also needed for
the RT1160 SOC as they use the same DSI IP.
Fixes#78299
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Remove CONFIG_SDMMC_VOLUME_NAME, and set the disk name based on the
``disk-name`` property. This aligns with other disk drivers, and allows
for multiple instances of the sdmmc_subsys disk driver to be registered.
Add disk-name properties for all in tree definitions for the
sdmmc-subsys disk driver, and change all in tree usage of the disk name
Fixes#75004
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This causes a build error as nRF70 driver running on CPU APP needs this
when SR co-existence is enabled.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Add variant for the coex interface and move the coex interface out
if the wifi/control interface variants.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Exclude the coex interface if the coex variant of the nrf7002eb
is selected instead of adding the interface alongside the
wifi/control interface.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
The `HCI_SPI` symbol is now automatically selected from devicetree,
removing the need for board specific defaults.
Signed-off-by: Jordan Yates <jordan@embeint.com>
The peer remote device "source_dev" can be retrieved from the
remote-endpoint-label. Direct reference via phandle is not needed.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The peer remote device "sensor_dev" can be retrieved from the
remote-endpoint-label. Direct reference via phandle is not needed.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The ov5640 camera driver now supports both MIPI CSI2 (DPHY) and DVP
modes. It is in MIPI CSI2 mode in this overlay. Add bus-type property
for this. In this mode, data-lanes property is required as well.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
This updates the documentation of all the NXP boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Adds a new shield definition for the Analog Devices EVAL-ADXL362-ARDZ
accelerometer shield. This shield provides support for an ADI ADXL362
3-axis accelerometer over an Arduino SPI connector.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Adds a new shield definition for the Analog Devices EVAL-ADXL372-ARDZ
accelerometer shield. This shield provides support for an ADI ADXL372
3-axis accelerometer over an Arduino SPI connector.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Use EXTRA_CONF_FILE in documentation .rst/.md files,
that replaced deprecated OVERLAY_CONFIG since the Zephyr v3.4 release.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
