Add Clock Control support for board RZ/G3S-SMARC
Signed-off-by: Tien Nguyen <tien.nguyen.zg@renesas.com>
Signed-off-by: Nhut Nguyen <nhut.nguyen.kc@renesas.com>
- Add a condition to check the clock supplying the CPU to match with
CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC
- Correct CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC for EK-RA4W1
Signed-off-by: Tran Van Quy <quy.tran.pz@renesas.com>
Add minimal support for Renesas EK-RA4M1 board with
basic gpio, pinctrl, uart, clock control and counter
drivers"
Signed-off-by: Tran Van Quy <quy.tran.pz@renesas.com>
- Update the overlapping irq number between port_irq4 and spi1
- Remove irq number for sci9 as it exceeds the limit (32 irq numbers)
Now users will define the irq numbers themselves
Signed-off-by: Quy Tran <quy.tran.pz@renesas.com>
Currently, the SPI pinctrl is incorrect for the spi0 node.
In this PR (#77850), we changed the pinctrl number for SPI
from spi0 to spi1, but we forgot to update the node name
to spi1.
This commit aims to fix:
- Correct the pinctrl name for spi
- Correct the spi node on ek_ra8d1.dts
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
This commit removes all references to the `xtools` toolchain variant in the
board YAML files.
Note that the `xtools` toolchain variant has been deprecated since Zephyr
v3.3.0 and now removed.
The removal process was automated using the following command line:
git grep -l xtools -- boards/*.{yml,yaml} | \
xargs -n 1 -P $(nproc) \
yq -i 'del(.toolchain[] | select(. == "xtools"))'
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Enabling `CONFIG_INPUT_FT5336_INTERRUPT` if the ft5336 node in DT
has `int-gpios` property.
As a result of this change, some boards can eliminate lines that
explicitly configure `CONFIG_INPUT_FT5336_INTERRUPT`.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
There are 4 Kconfig names about the "Draw Buffer". Rename 'VBD' to 'VDB'
in Kconfig option 'LV_Z_*VBD*_CUSTOM_SECTION' to make name consistent.
config LV_Z_VDB_ALIGN
int "Rending buffer alignment"
config LV_Z_VBD_CUSTOM_SECTION
bool "Link rendering buffers to custom section"
config LV_Z_DOUBLE_VDB
bool "Use two rendering buffers"
config LV_Z_VDB_SIZE
int "Rendering buffer size"
default 100 if LV_Z_FULL_REFRESH
And the draw buffer definition is now:
static uint8_t buf0[BUFFER_SIZE]
#ifdef CONFIG_LV_Z_VDB_CUSTOM_SECTION
Z_GENERIC_SECTION(.lvgl_buf)
#endif
__aligned(CONFIG_LV_Z_VDB_ALIGN);
Signed-off-by: Haiyue Wang <haiyuewa@163.com>
- Add "channel-available-mask" property in ADC node
to detect which channels are available to use
- Add "add-average-count" property in ADC node to chose
number of count of the addition or average mode
- Change the source code of ADC to match with 2 new properties.
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
Add support for UDC on highspeed port on these boards:
- ek_ra8m1
- ek_ra8d1
- ek_ra6m5
- ek_ra6m3
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
This is the initial commit to support pinctrl driver for Renesas RZ/G3S
Signed-off-by: Quang Le <quang.le.eb@bp.renesas.com>
Signed-off-by: Nhut Nguyen <nhut.nguyen.kc@renesas.com>
This adds minimal support for board RZ/G3S-SMARC
Signed-off-by: Nhut Nguyen <nhut.nguyen.kc@renesas.com>
Signed-off-by: Tien Nguyen <tien.nguyen.zg@renesas.com>
Signed-off-by: Binh Nguyen <binh.nguyen.xw@renesas.com>
- Add support CAN-FD for EK-RA6E2, EK-RA4E2
- Enable ioport for can-transceiver on EK-RA6E2, EK-RA4E2
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
Add entropy support for these boards: ek_ra6m1, ek_ra6m2, ek_ra6m3
Signed-off-by: Danh Doan <danh.doan.ue@bp.renesas.com>
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
Enable Ethernet controller node and mdio node for RA boards.
Add pinctl for mdio and Ethernet usage
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Gap filling in hex files are now disabled per default, and therefore
there is no reason to explicitly disable gap filling.
It has never been possible to disable gap filling in binary files.
Disabling gap filling would just result in the binary file to be gap
filled with the tool's default value, objcopy=0x00.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Add missing "pinctrl-names" and "status" properties for
the spi1 node in ek_ra8m1.dts to able to test spi_loopback
on ek_ra8m1
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
Added mikrobus_header, mikrobus_i2c, mikrobus_spi and mikrobus_serial
node labels to da14695_dk_usb device tree board definition, allowing
compatible shield boards to be used. Also fixed minor issues with
pin assignment and header labelling.
Signed-off-by: Ian Morris <ian.d.morris@outlook.com>
Added pmod_serial and pmod_header node labels to EK-RA8M1 device
tree board definition, allowing compatible shield boards to be used.
Signed-off-by: Ian Morris <ian.d.morris@outlook.com>
Remove CONFIG_MMC_VOLUME_NAME, and set the disk name based on the
``disk-name`` property. This aligns with other disk drivers, and allows
for multiple instances of the mmc_subsys disk driver to be registered.
Add disk-name properties for all in tree definitions for the
mmc-subsys disk driver, and change all in tree usage of the disk name
Fixes#75004
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
