Updated uart_rx_enable() and uart_tx() to use timeout given
in microseconds. Previously argument was given in milliseconds.
However, there are cases when milliseconds granularity is not
enough and can significantly reduce a throughput, e.g. 1ms is
100 bytes at 1Mb.
Updated 4 drivers which implement asynchronous API. Updated
places where API was used.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Remove CC1200 and CC2520 devicetree nodes from the test as they are not
sensors and are not being built by this test regardless.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Adds build_all for ieee802154 drivers. A substantial number of drivers
are for SoC peripherals, so test cases are required many boards.
Fixes#11519.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Remove two unused files that were left floating around when the
build_all sample was split up.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Configure the target board to PASS the test case.
The PCLK2 clock feeding the SPI1 is reduced by 2 (apb2 prescaler)
to accept the slow freq config.
The SPI1 MISO and MOSI pins are linked on the HW board
(on arduino CN13, D11 & D12)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Move memory.h out of the way in a more "private" space
(include/linker/devicetree_reserved.h) to prevent polluting the
devicetree space.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
For some reason, provided pin configuration for nucleo_f103rb
is not able to detect gpio callback issues.
Move to other pin combination which detect pin callback issues.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Fixes: #38403
Adding NET_DRIVERS menuconfig so that network drivers are grouped
together in its own menu entry under drivers, similar to most other
drivers.
This further has the advantages that `CONFIG_NET_DRIVERS` can be used
for testing to determine if network drivers has been selected.
This changed revealed a dependency loop where both `select` (for SLIP)
and `depends` (for PPP) which both depends on NET_DRIVERS` where in use
in the dependency tree for Qemu networking, especially NET_SLIP_TAP.
This is handled by defaulting `NET_DRIVERS` to `y` when building for a
Qemu target.
`SLIP` had a dependency to `!QEMU_TARGET || NET_QEMU_SLIP`. This is
changed so that SLIP prompt depends on `!QEMU_TARGET` which provides
full user control in hardware but makes the symbol promptless on Qemu
targets.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
1. Add support for multiple syscon entries (as a side effect, this also
fixed syscon.c implementations which weren't being linked to their
syscon.h counterparts).
2. Add support for different width registers in syscon.
3. Add tests for syscon
Signed-off-by: Yuval Peress <peress@chromium.org>
Remove the HL7800 DTR device tree binding because the
DTR IO is not needed for operation of the HL7800
modem.
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
This commit corrects the DMA channels for the asynchronous
UART API testing support on the SAM R21 Xplained Pro board.
Signed-off-by: Ron Smith <rockyowl171@gmail.com>
For getting the address of the RAM region in the application we need to
extend the api for the flash_simulator.
This path introduce flash_simulator_get_memory() call which allow to
do so.
Signed-off-by: Sigvart Hovland <sigvart.m@gmail.com>
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Adding adp_xc7k_ae350 board support based on andes_ae350 soc. It's base
support and only contains uart/gpio drivers.
Signed-off-by: Jim Shu <cwshu@andestech.com>
Note that the it8xxx2 does not support a status register so that
functionality is omitted.
This change also adds driver tests that build both the npcx and it8xxx2
drivers.
Signed-off-by: Yuval Peress <peress@chromium.org>
It enables the usart6 to run the testcase with a DMA
tests/drivers/uart/uart_async_api. DMA2 (of type V1)
is configured on channel 5 (request) streams 7 & 2.
USART Tx and Rx PG14 - PG9 pins (14 & 16 of CN10)
are connected to PASS the test.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds basic support for the Silabs Si7210 hall effect magnetic
position and temperature sensor. It is able to get magnetic field and
temperature in the default scale of the sensor (depending on the
variant). It also supports going into sleep mode without measurements
through the device power management infrastructure.
It is most notably missing support for scale change, measurement
averaging and filtering, and alert pin configuration (threshold,
hysteris, tamper).
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Allow UART driver that offload interrupt processing
to workuqueue, like CDC ACM UART to work.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
This sets the dts of DMA for using pn the uart 2 i.
The stm32h723 has a DMAMUX and request are 44 and 43 for usart2
The Tx&Rx pins PD5 and PD6 of the usart2 are connected
on the nucleo_h723zg board to pass the test
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Move to CMake 3.20.0.
At the Toolchain WG it was decided to move to CMake 3.20.0.
The main reason for increasing CMake version is better toolchain
support.
Better toolchain support is added in the following CMake versions:
- armclang, CMake 3.15
- Intel oneAPI, CMake 3.20
- IAR, CMake 3.15 and 3.20
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
This is now failing an edtlib check for unknown vendor prefixes.
I can't find a reason to use a vendor prefix in application-local
bindings like this, so just remove it wherever it appears by
normalizing to test-foo-compat instead of test,foo_compat or
test,foo-compat.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
I can't find any reference anywhere showing that the manufacturer of
the LPD8803 or LPD8806 LED scripts is a company called 'colorway'.
Use 'greeled' instead; these seem to actually be manufactured by
GreeLed corporation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
It should be "maxim,max30101", because the vendor prefix for this
company is "maxim", not "max".
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
It should be "u-blox,sara-r4", because the vendor prefix for this
company is "u-blox", not "ublox".
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
add configuration for testing the spi through the dma1
on the nucleo_l152re target. This test requires the MOSI pin
to be connected to the MISO pin on the board.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add configuration for testing the usart3 through the dma1
on the nucleo_l152re target.This test requires the Tx pin
to be connected to the RX pin on the board.
Pin definition is added for this usart instance.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This is a follow-up to commit 954dfa755b.
Apply adjustments made in the i2s_api test to the i2s_speed one so that
it can also be executed successfully on the nRF DK boards.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Modified test to handle case when counter handlers are called in
ZLI interrupt context where kernel primitives cannot be used. In
that case volatile counters are used to track number of handlers
calls.
Added configuration for nrf52840dk board where zli feature is enabled
for all counters.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
