After 'flash_ex_op' syscall was added we are able to expose vendor
specific features to the user.
This patch moves existing tests to 'tests/drivers/common'. New tests for
vendor specific operations should go to vendor directory under
'tests/drivers/flash'.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
Add property mxicy,mx25r-power-mode to jedec,spi-nor binding for
controlling low power/high performance mode on Macronix MX25R* Ultra Low
Power flash devices.
- "low-power" configures the flash in ultra low power mode.
- "high-performance" configures the flash in high performance mode.
Signed-off-by: Gregers Gram Rygg <gregers.gram.rygg@nordicsemi.no>
Increasing the stack size to pass the
tests/drivers/flash testcase on the disco_l475_iot1 disco kit.
Note that CONFIG_MPU_ALLOW_FLASH_WRITE is set.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
this commit adds an overlay to run the tests/drivers/flash
on the b_u585i_iot02a_ns target platform.
It renames the non-secure partition to slot1_ns_partition
to match the testcases.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
When there is no external pull-up on the CSN line and the line
is put into the low-power mode (input direction and disconnected
buffer), after some time its level falls to low and some flash
chips, like for example MX25R64, exit the Deep Power-down mode
when that happens. To prevent this, activate the GPIO internal
pull-up for this line in boards that do not have the external
pull-up on it.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The SPI flash were recently changed to use an alias to identify the
flash chip in:
64fbbd9a44 boards: Add alias to boards with spi-flash node
This caused some CI test failure for the nrf52840dk test with the
nrf52840dk_mx25l51245g overlay, as it changes the flash nodelabel of the
board dts file. Adding the correct alias to the overlay file to point to
the correct one.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
- The MX25UM51345G flash is connected to FLEXSPI PortA for
mimxrt595_evk.
- Updated flexspi_mx25um51345g driver to support DTR OPI mode.
- Tested with tests/drivers/flash.
Signed-off-by: Chay Guo <changyi.guo@nxp.com>
Added overlay with DTS of MX25L51245G qspi flash
memory. DTS configures qspi clock to 2 MHz which is supported
by nRF52840.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
If a user has a 1GB external flash it is currently not possible
to configure this through DTS. To allow for such a configuration
we add an option which specifies the size in bytes not bits.
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.no>
Restore the testcase to run on the qspi nor-flash controller
of the disco_l475_iot1 board
of the disco stm32f746 board
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit enables soc-flash support in disco_l475_iot1
only for flash test. Using overlays, it adds soc-flash storage
partition and deletes qspi-flash storage parition for
flash test. Both flash test and spi_flash application
has been tested on disco_l475_iot1 platform.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
This commit enables soc-flash support in stm32f746g_disco only for
flash test. Using overlays, it adds soc-flash storage partition and
deletes qspi-flash storage partition for flash test. Both flash test and
spi_flash application has been tested on stm32f746g_disco platform.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
Test include non-aligned read in nrf_qspi_nor flash and
SoC flash memory to buffer with variable size.
It checks all possible variants of alignment and size.
Signed-off-by: Mateusz Syc <Mateusz.Syc@nordicsemi.no>
