The native_sim has already been added to the test cases of
`drivers.ieee802154.build.external` is not being appropriately
processed because there is no corresponding overlay.
Create an overlay as an alias of native_posix.overlay.
Also, add the native_sim/native/64 platforms in the same way.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Use `test_adc` in io-channels to be consistent in whole
tests/drivers/build_all/sensor/adc.dtsi file.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Install the second instance to 0x8(uei), because MSI is installed
to 0x3(msi) when SMP is enabled.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Add all the necessary files to add apds9253 Avago sensor driver.
Sensor available at https://docs.broadcom.com/doc/APDS-9253-001-DS
Signed-off-by: Margherita Milani <margherita.milani@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
- Update `MAX_IRQ_PER_AGGREGATOR` to 1024 to match with the
devicetree
- Update `2ND_LEVEL_INTERRUPT_BITS` to 11 bits to
be able to encode the L2 IRQs.
- Update `NUM_IRQS` to 1036 (L1 has 12, L2 has 1024)
Update the `MAX_IRQ_PER_AGGREGATOR` config in testcase
accordingly, so that it won't overflow the configured bits.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
The linear battery charger will charge the connected battery up
to a specific voltage. This is different depending on the chemistry
of the battery. Most LiPo Batteries have a nominal voltage of 4.2V,
which is why the default voltage of the bq25180 is 4.2V.
Signed-off-by: Fabian Pflug <fabian.pflug@grandcentrix.net>
Some hardware configuration require rely on the ALERT/RDY
pin to know when and ADC conversion is completed.
The polling thread is left as fallback, when the pin
is not defined.
Signed-off-by: Efrain Calderon <efrain.calderon.estrada@gmail.com>
This transforms the existing driver for the Microchip MCP9808
to be used as a generic driver to be used with all
JEDEC JC 42.4 compliant temperature sensor chips.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
Fix warnings generated when performing sensor drivers build test
due to typos in i2c DT definition.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add missing braces to comply with MISRA C:2012 Rule 15.6 and
also following Zephyr's style guideline.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
The LSM9DS1 is a system-in-package featuring
a 3D digital linear acceleration sensor, a 3D digital angular rate
sensor and a 3D digital magnetic sensor.
This driver implements only the linear acceleration sensor and the
angular rate sensor, on the I2C bus.
This driver is without trigger support.
The driver is based on the stmemsc HAL.
link: https://www.st.com/resource/en/datasheet/lsm9ds1.pdf
Signed-off-by: Miguel Gazquez <miguel.gazquez@bootlin.com>
The driver right now only allows inverting the input value, which can be
useful for differential channels but is quite confusing for single ended
ones. Implement a simple output inversion flag instead to make up for
that.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
These properties are not used by the driver at all, but are
inconveniently marked as required. Lets just remove them.
Signed-off-by: Brett Witherspoon <brett@witherspoon.engineering>
In order to support back-to-back readings, it's required that the
RTIO workq threads priority is higher than the caller issuing the
back-to-back requests, otherwise the requests will fail as P4WQ won't
have the opportunity to clear the is_done semaphore, and the subsequent
request will be rejected.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
Fix the devicetree bindings to actually be used as the default
configuration, following the example set by various ST sensor devices.
This requires sadly dropping enums and using #defines for various
options as well as repeating many numbers, but presumably is the way to
do it given the precedent set by ST with sensors like the lsm6dso.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
`checkpatch.pl` requires that dts sources are indented with tabs,
fix all the spaces that slipped in while checkpatch wasn't watching.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Coverity found this legitimate issue: the datasheet specifies PS_IT
being 2-bits long (1, 2, 4, 8) and this driver assumes more steps are
available. Remove extraneous fields so the Proximity integration
setting fits in the expected 16-bit value.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
These three sensor types are all largely compatible. The SHT21 and
HTU21D can be supported by this driver by sending command 0xE3 instead
of 0xE0 to read the temperature.
Mention the sensor names in bindings and Kconfig to help those looking
for support to find it. There have been at least five PRs attempting to
add SHT21 and/or HTU21D support that did not realize the Si7006 is the
same.
As mentioned in PR #22862, the Sensirion SH21 is the original. The dts
bindings are adjusted (in a backward compatible way!) to make the sht21
the base binding and si7006 is derived from that.
Examples of dts compatibles:
TE Connectivity née Measurement Sepcialties HTU21D:
compatible = "meas,htu21d", "sensirion,sht21";
Sensirion SHT21:
compatible = "sensirion,sht21";
Silicon Labs Si7006
compatible = "silabs,si7006";
Silicon Labs Si7021
compatible = "silabs,si7021", "silabs,si7006";
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Add SENSOR_ATTR_ALERT and SENSOR_ATTR_HYSTERESIS attributes support.
The code is heavily inspired by the one for lm77 sensor.
Signed-off-by: Benjamin Lemouzy <blemouzy@centralp.fr>
Clean up register addresses for devices defined as children of the dummy
SPI bus, so that they start from zero. This ensures all SPI chip select
gpio indices will be used
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Convert galaxycore GC9X01 to MIPI DBI API. In tree boards and tests
using this display have also had their devicetrees updated to use the
new MIPI DBI SPI emulated device.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add a driver for the National/TI LM95234 Quad Remote Diode and Local
Temperature Sensor with SMBus Interface and TruTherm Technology.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Rename all Silicon Labs radio boards to always use the official kit name of
the kit containing only the radio board as board target name. Disentangle
boards using Series 1 and Series 2 SoCs that have almost nothing in common
in terms of devicetree content, but still occupied the same directory.
As part of the initial HWMv2 port, all radio boards were merged into a
single target efr32_radio, using the SoC as a board qualifier to target
specific boards. This was unfortunate, as the SoC name is not sufficient
to identify a specific board -- the same SoC may be used on multiple
different boards. This commit reinstates every radio board as an individual
board target.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Rename the current sensor_read to sensor_read_async_pool and create a
new blocking sensor_read helper.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
