Add mfd_adp5585 and gpio_adp5585 driver. This driver enables ADP5585
as an GPIO expander.
This chip is used as an GPIO expander on i.MX93 EVK. GPIO pinctrl,
read/write and interrupt is supported.
Note that ADP5585 has 2 GPIO banks with 5 pins each. The driver combines
two group into a 16-bit port. Index 0~4 correspond to R0~R4 lines, index
8~12 correspond to C0~C4 lines. Index 5~7 is reserved unavailable.
Signed-off-by: Chekhov Ma <chekhov.ma@nxp.com>
Rename ad5592 files in dts, driver and include to ad559x and add support
for I2C bus which is required for AD5593.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Added configuration of long press reset functionality.
Includes ship/hibernate to wake debounce time and
disabled/one_button/two_button mode selection.
Signed-off-by: Andy Sinclair <andy.sinclair@nordicsemi.no>
Split up the driver for the PWM controller MAX31790
into a multi function device driver.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Split up the driver for the low side switch BD8LB600FS into a GPIO
and MFD part.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
This binding is for the NXP FlexComm Interface. The
driver will setup an interface for use as a UART, SPI
or I2C device.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
By default N_VBUSEN signal is used by the host to define if VBUS
signal should be used for power supply (VBUS-IPSOUT).
This feature enables the possbibility to change this behaviour.
When N_VBUSEN detection is disabled, axp192 will automatically
decide to use VBUS (REG10H[7] = 1).
Please refer to datasheet for details.
Signed-off-by: Martin Kiepfer <mrmarteng@teleschirm.org>
Maxim MAX20335 is a PMIC with Ultra-Low IQ Voltage Regulators and
Battery Chargers for Small Lithium Ion Systems.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
The Nuvoton NCT38xx is a multi-function device providing a TCPC
controller and a I/O expander (GPIO driver). Add a multi-function
driver to manage exclusive access to the device.
Tested with "twister -T tests/drivers/build_all/gpio".
Signed-off-by: Keith Short <keithshort@google.com>
AXP192 is a small and simple power management IC featuring different
LDOs, DCDCs, AINs and also GPIOs. It also offers functionaltiy for
battery management.
This change includes the basic regulator driver functionaltiy for
LDO2-3 and DCDC1-3 as well as the mfd driver layer. Further drivers
for GPIO and ADC will follow.
Drivers have been developed and tested on M5StackCore2, an ESP32-based
board. Support for M5StackCore2 is still in progress.
Signed-off-by: Martin Kiepfer <mrmarteng@teleschirm.org>
Add an API-less MFD driver for nPM6001. In this case, the MFD device
driver doesn't expose any API as plain I2C API is used within other
device drivers (regulator, GPIO, watchdog). This driver just initializes
some device properties.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add a new regulator driver for Analog Devices ADP5360. While it is a MFD
device, only support for BUCK/BUCKBOOST regulators is added in this
patch.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add a new reset driver for GD32 platforms. This driver controls the
reset registers from the RCU peripheral. It can be used to restore
peripherals to their initial state when initializing a device.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
