Introduce GPIO-based driver for MIPI DBI class that allows MIPI DBI
type A and B displays to be used on general platforms.
Since each data pin GPIO can be selected individually, the bus pins are
set in a loop, which has a significant negative impact on performance.
When using 8-bit mode and all the data GPIO pins are on the same port,
a look-up table is generated to set the whole port at once as a
performance optimization. This creates a ROM overhead of about 1 kiB.
Tested 8-bit 8080 mode with ILI9486 display on nRF52840-DK board.
Signed-off-by: Stefan Gloor <code@stefan-gloor.ch>
- Create a new compatible: nordic,nrf53x-oscillators, as other series,
e.g. nRF54LX contain a similar but different IP (with PLL control,
etc.)
- Adjust DT: use recommended node name, remove redundant status okay.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Register all the lpi2c instances.
Add no-power-level property and update driver
to adapt no-power-level property.
Signed-off-by: Lucien Zhao <lucien.zhao@nxp.com>
This defines raspberrypi,pico-xosc along with a configurable startup
delay multiplier. On some boards, the XOSC takes longer to stabilize.
Signed-off-by: Xudong Zheng <7pkvm5aw@slicealias.com>
Now that we support internally connected channels we should make the
pinctrl configuration optional.
Signed-off-by: Corey Wharton <xodus7@cwharton.com>
Indicate in the STM32WB0 power controller binding that the SMPS output
current limitation is a feature only available on STM32WB05 and STM32WB09.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
`-` is preferred over `_` in devicetree property names.
Since, change `clk_src`, `clk_div`, and `clk_out_div` to
`clk-src`, `clk-div`, and `clk-out-div`.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Add timer instance in device tree
Add timer yaml file
Timer0/1/2/3 are common for MAX32xxx MCUs
MAX32655 has additional Timer4/5 which are low power timers
Co-authored-by: Mert Vatansever <mert.vatansever@analog.com>
Signed-off-by: Sadik Ozer <sadik.ozer@analog.com>
Add information to the device tree if UARTE instance has a HW feature
which is the ENDTX_STOPTX short.
Add this property to all instances in nrf54hl15, nrf54l20, nrf9280
and nrf54h20.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
There are numbers of drivers for different PCA(L) series chip. They
share similiar register layout and control logic. This driver intends
to unify these drivers for PCA(L)xxxx series i2c gpio expanders.
Signed-off-by: Chekhov Ma <chekhov.ma@nxp.com>
Implement an option manual reset of the PCAL64XXA to allow the external
implementation of a retention of the port expander state.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Adds a new DTS prop for i3c devices as support for the CCC SETAASA
requires prior knowledge of the target if it supports it according
to i3c spec v1.1.1 section 5.19.3.23.
This will be used as an optimization for bus initialization.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
Set a default value for constant-charge-voltage-max-microvolt, matching
the device hardware default, this ensure compatibility with existing
applications that did not specify the recently introduced property.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add all the necessary files to add apds9253 Avago sensor driver.
Sensor available at https://docs.broadcom.com/doc/APDS-9253-001-DS
Signed-off-by: Margherita Milani <margherita.milani@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Add new binding and a node to nrf54h20. Update Kconfig and nrfx_config
to include nrfx_tbm driver when node with that compatible is enabled.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
The current driver contains assembly code which is specific for the nRF51
SOC which makes it incompatible with other SOC's. This patch adds support
for other nRF SOC's as well. The timing is calucated based on the CPU clock
frequency, but can be configured manually as well if needed.
Changes have been verified on a Adafruit Feather nRF52840 Express board,
which contains a single NeoPixel RGB LED. Timings have been verified using
a scope connected to the WS1812 data line.
Signed-off-by: Chaim Zax <chaim.zax@zaxx.pro>
Added XGMAC0, XGMAC1, XGMAC2 device nodes in
intel_socfpga_agilex5 dts file with default
parameter values and default device node status
as 'disabled'.
Signed-off-by: Santosh Male <santosh.male@intel.com>
Devicetree binding for NXP mcxc oscillator is not available.
Add the binding to be able to configure the oscillator in devicetree.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Add configuration settings for the FOPT, FSEC, and flash configuration
offset to the FTFA module binding.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Charging a battery has three phases (compare Figure 8-2 in
https://www.ti.com/lit/ds/symlink/bq25180.pdf)
First is a pre-charge phase, then a constant current, then a constant
voltage phase.
During the pre-charge phase, the battery is only charged with a very low
current, to not damage the cells, because they are below a threshold,
that is considered healthy for the battery and need to be brought back
up to a healthy voltage.
Signed-off-by: Fabian Pflug <fabian.pflug@grandcentrix.net>
The linear battery charger will charge the connected battery up
to a specific voltage. This is different depending on the chemistry
of the battery. Most LiPo Batteries have a nominal voltage of 4.2V,
which is why the default voltage of the bq25180 is 4.2V.
Signed-off-by: Fabian Pflug <fabian.pflug@grandcentrix.net>
Add bindings for nrf-fll16m and nrf-lfclk and update in-tree nodes
and boards to use them in place of the fixed-clock binding.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
The HFXO and LFXO oscillators have properties which need to be
specified in the devicetree. These properties are used by clock
controllers, which get these properties from the devicetree.
The BICR also contains these properties. For now, the properties
are duplicated in the bicr node in the devicetree.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
U-Blox LARA-R6 was added to modem_cellular, and an additional state
was introduced where the UART baudrate is changed if the modem supports
it
Signed-off-by: Emil Lindqvist <emil@lindq.gr>
