The current atmel,sam-tc-qdec sensor implementation shared the timer
counter node. This create issues when users wants define both modes.
The current proposal changes the qdec dedinition to be a child of
tc and refactor all the chain of definitions.
Fixes#71312
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Remove all optional, initial CAN sample point properties and rely on the
CAN timing calculations to automatically pick the preferred sample point
location based on the initial bitrate.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This commit adds layput page cells to the atmel sam flash
controller and the flash node. These allow for describing
the actual flash page layout of each soc, allowing the
flash driver to fully utilize the capabilities of the
flash.
With this update, we unlock the following capabilties:
- utilize 2048 erase block size for small sectors
- utilize 16384 erase block size for large sectors
Signed-off-by: Bjarki Arge Andreasen <bjarkix123@gmail.com>
Consistently use "int0" and "int1" as interrupt names for CAN controllers
based on the Bosch M_CAN IP core. This aligns with the upstream Linux
bindings.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This removes all occurrences of arm,num-mpu-regions relying on the value
reported by the register instead.
A user may still define this property if they need to have a compile time
definition for it.
Signed-off-by: Wilfried Chauveau <wilfried.chauveau@arm.com>
Initialize the MDIO peripheral clock (normally done during GMAC
initialization) before trying any MDIO transfers, preventing startup
errors.
Signed-off-by: Nick Kraus <nick@nckraus.com>
This commit adds the RTC device to the following
atmel sam devicetrees:
- sam3x.dtsi
- sam4e.dtsi
- sam4s.dtsi
- same70.dtsi
Signed-off-by: Bjarki Arge Andreasen <bjarkix123@gmail.com>
Updates Ethernet PHY devicetree bindings to be more consistent with
Linux by using the standard `reg` property for the PHY address instead
of a custom `address` property. As a result, MDIO controller bindings
now require standard `#address-cells` and `#size-cells` properties.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Update the descriptions for the various CAN devicetree timing properties
specified in Time Quanta (TQ) to make it clear that these, if present, are
only used for the initial timing parameters.
Deprecate the (Re-)Synchronization Jump Width (SJW) devicetree properties
for both arbitration and data phase timing as these are now only used in
combination with the other TQ-based CAN timing properties, which are all
deprecated.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This creates separate dtsi files for the various memory density codes of
SAM X2xfamilies (they are the same where the specific size exists.)
All of the boards with the exclusion of EV11L78A use the same density
model of 18 (32KiB RAM and 256KiB flash) which is what the samd2x.dtsi
include specified for all of them previously.
The density code has been confirmed being the same across the D20/D21,
C20/C21, L21, and R21 families. This does not carry over to some other
series such as the E5x.
Signed-off-by: Diego Elio Pettenò <flameeyes@meta.com>
This commit adds support for the ATMEL HSMCI peripheral
for the SAM4E MCU series, enabling native SD card support.
Signed-off-by: Vincent van Beveren <v.van.beveren@nikhef.nl>
Make ethernet phys childs of the mdio device and move the mdio device up
a level on the tree. That makes the device hierarchy coherent with the
required initialization priority and allows keeping the sequence in
check with CHECK_INIT_PRIORITIES.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Restructure the Bosch M_CAN driver backend to use per-instance Message RAM
configuration.
This removes the need for a common, artificial "can" devicetree node for
SoCs with multiple Bosch M_CAN-based CAN controllers and allows for
per-instance configuration of the number of e.g. standard (11-bit) and
extended (29-bit) filter elements.
As part of the restructure, software handling of CAN filter flags was moved
from per-flags bitfields to per-filter bitfields, solving an issue when
using more than 32 standard (11-bit) filter elements or more than 16
extended (29-bit) filter elements.
Fixes: #42030, #53417
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Switch the Bosch M_CAN devicetree binding to use a bosch,mram-cfg property
for specifying the memory layout of the Bosch M_CAN Message RAM. This is
identical to the Linux kernel devicetree binding for Bosch M_CAN IP core
based CAN controllers.
This introduces an offset cell which can be used for controllers with
shared Message RAM between Bosch M_CAN instances.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Let the Bosch M_CAN front-end drivers supply their own register read/write
functions.
This is preparation for handling non-standard Bosch M_CAN register layouts
directly in the front-end and for accessing Bosch M_CAN IP cores over
peripheral busses.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The SERCOM4 is hardwired to PB30/31, PC18/19 internally for the LoRa
radio. Move the pinctrl entries to SoC dts level. The same applies for
samr35.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In general, peripherals should be disabled by default and enabled at
board level when needed.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This update devicetree entries and Kconfig definition to allow use of
reset cause on all SAM series.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add initial version of clock control for Atmel SAM SoC series. This add
support to Power Management which allows control peripherals clock.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Set the status of the DMA controller, xdmac, to disabled. In effect
changing the default status from okay to disabled for all sam e70
based board.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Adds Atmel SAMC20 and SAMC21 soc. C series is based on Cortex-M0+.
C21 contains CAN interface.
The init routines are same for SAMC20 and SAMC21. They use one
clock OSC48M without configuration.
The code is inspirated from atmel_sam0/samd21.
Signed-off-by: Kamil Serwus <kserwus@gmail.com>
