Rather setting the driver default in soc, make it directly at symbol
level rather than soc and clean up redundant `select` occurrences.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
GT911 driver was reading an additional touch point into the stack
defined touch point array, causing an out-of-bounds write on the stack.
Fix this issue by adjusting the limit on the for loop, and add a note
to the driver as to why we don't need to validate the number of points
reported for future developers
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
A connected state was reported as a disconnected state.
This led to wrong reports of the connected state to all systems
relying on it.
Signed-off-by: Lukas Gehreke <lk.gehreke@gmail.com>
ethernet driver
This driver is capable of supporting basic features
of synposys dwc-xgmac ethernet MAC IP. Basic features
includes,
1. Tx and Rx, multiple Tx and Rx DMA channels, multiple
Tx and Rx queues
2. Check Sum Offloading on Tx and Rx for IPv4, IPv6,
TCP, UDP and ICMP packets
3. 10M/100M/1G speeds, Autonegotiation, Link speed
configuration, Promiscuous mode, Full/Half
duplex configuration
4. Added source files for synopsys dwc xgmac mdio driver.
synopsys dwc xgmac mdio driver fetures includes:
It supports clause 22 of IEEE 802.3 for ethernet PHY devices
management.
5. Extended mdio shell support for dwcxgmac mdio driver.
Signed-off-by: Santosh Male <santosh.male@intel.com>
LPUART without modem support is used in some NXP socs. Build error
occurs for such socs because of accessing unavailable register.
Fix it by adding #if directive for checking modem support availability.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Charging a battery has three phases (compare Figure 8-2 in
https://www.ti.com/lit/ds/symlink/bq25180.pdf)
First is a pre-charge phase, then a constant current, then a constant
voltage phase.
During the pre-charge phase, the battery is only charged with a very low
current, to not damage the cells, because they are below a threshold,
that is considered healthy for the battery and need to be brought back
up to a healthy voltage.
Signed-off-by: Fabian Pflug <fabian.pflug@grandcentrix.net>
The battery charger will stop charging the battery if it believes,
that is is completely charged. If the battery drops below a certain
voltage threshold, then the battery charger starts charging the
battery again.
For the bq25180 the threshold can only be one of either 100mV or
200mV below the VSET voltage.
See table 8-16 Bit 5 in https://www.ti.com/lit/ds/symlink/bq25180.pdf
Signed-off-by: Fabian Pflug <fabian.pflug@grandcentrix.net>
The linear battery charger will charge the connected battery up
to a specific voltage. This is different depending on the chemistry
of the battery. Most LiPo Batteries have a nominal voltage of 4.2V,
which is why the default voltage of the bq25180 is 4.2V.
Signed-off-by: Fabian Pflug <fabian.pflug@grandcentrix.net>
Add custom clock_control API for nRF platforms that allows requesting
clocks with specified minimal required attributes (accuracy, precision,
and frequency). Provide an implementation of this API for FLL16M, HFXO,
HSFLL, and LFCLK controllers in the nRF54H20 SoC.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
It has been observed that using a CMUX max frame size of 127
causes FCS errors; smaller or larger works. This commit sets the max
frame size to the modem's default value.
Signed-off-by: Emil Lindqvist <emil@lindq.gr>
U-Blox LARA-R6 was added to modem_cellular, and an additional state
was introduced where the UART baudrate is changed if the modem supports
it
Signed-off-by: Emil Lindqvist <emil@lindq.gr>
Move some STM32 drivers related Kconfig symbols from `config`
to `menuconfig` when driver options depends on these symbols.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
This driver is mostly rewritten from scratch, with some parts borrowed
from the usb_dc_rpi_pico driver implemented by Pete Johanson.
This driver does not use any function from RPI PICO HAL and actually
could be furter improved to not use any defines or types from the HAL as
they are confusing and overdo it with volatile qualifiers.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Provide a new kconfig option which can be used to disable
the default seeding of the host standard library random
generator by this driver.
This allows some other component to do so without this component
default initialization interfering.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Zephyr drivers have typically one log level defined per class. The video
drivers were making exception. This adds the missing log level for video
drivers.
Since all headers had to be modified, this also:
- Update the log initialization to the new syntax from 5e34681
- Sort the #include list to something like #41543
Signed-off-by: Josuah Demangeon <me@josuah.net>
A warning was issued in the build as the rtio tx and tiny_tx buffer
pointers are now labeled const. The internal API expects mutable buffers
so an explicit cast is needed here to avoid the warning.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Currently DMA overrun errors are ignored. Forward the error
to the user using the UART_RX_STOPPED with UART_ERROR_OVERRUN
reason.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
If an overrun happens the user may decide to stop the dma which
unsets the DMA line. Currently, the line is always re-enabled after the
callback.
Switch the order around to fix the problem. Also, always reset the line
even if the user doesn't provide a callback.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Use the RTIO work queue to fake the i2c submit calls for drivers which
haven't yet implemented the API. Applications can change the size of
the work queue pool depending on how much traffic they have on the buses.
Signed-off-by: Yuval Peress <peress@google.com>
Right now "lp5562_led_blink" unconditionally find and assign a engine
that is not executing at the moment. This is an issue, if 3 "led" are
already using an engine. That is a call to "lp5562_led_blink" could
terminate with error, even if the "led" is already using an engine.
This commit fixes this issue by adding a check to see if engine is
linked and reuse it, otherwise assign a free engine.
Signed-off-by: Anuj Pathak <anuj@croxel.com>
`explorir_m_uart_flush_until_end` terminates immediately if the read
variable is initially equal to `EXPLORIR_M_MAX_RESPONSE_DELAY` and
`uart_poll_in` does not read anything.
Fix this by only checking the read variable if `uart_poll_in` reads a char.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
The initialization of the UARTE is attempting to handle potential
improper handover from the bootloader. This handling is additional
complexity which should be fixed in the bootloader or whatever
component is failing to deinit the UART properly.
This commit removes the handling of improper handover from the
bootloader, while additionally clearing the ERROR flag when suspending
the UARTE component.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
According to the official MBOX API documentation available at
https://docs.zephyrproject.org/latest/hardware/peripherals/mbox.html
mbox_sen() shall return
-EMSGSIZE – If the supplied data size is unsupported by the driver.
Fix error code returned by the mbox_send().
Signed-off-by: Sebastian Głąb <sebastian.glab@nordicsemi.no>
Initialise the semaphores in the init function so that a copy of the
data structure does not need to exist in `.data`.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Adds support for settings/getting RTC time and using alarm/update feature.
The alarm option needs all fields to be set due to a hardware limitation.
RTC shares the same interrupt with the watchdog. Thus shared
interrupts must be enabled when WDT and RTC both need to trigger the ISR.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
When build with the psa_crypto_driver, it will try to include common.h
of mbedtls, but actually include the common.h from hostap, and causes
build error of undefined symbol. Now link the library of hostap to use
the header file in /utils path, to fix the build error.
Signed-off-by: Maochen Wang <maochen.wang@nxp.com>
In corner case, the pending ISR will be triggered immediately
after enable the IRQ, this PR will setting CPU affinity first
to avoid routing the unexpected IRQ to other CPUs.
Signed-off-by: chao an <anchao@lixiang.com>
Select PINCTRL subsystem by drivers which require it.
Prevent the need from enabling this symbol at board or soc level.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
In the IT82xx2 chip, the ready bit is automatically cleared by
hardware. When setting other bits, there is a chance that the ready bit
hasn't been cleared yet, leading to unexpected USB transactions. This
change ensures that the ready bit is always set to '0' when setting the
endpoint control value.
Signed-off-by: Ren Chen <Ren.Chen@ite.com.tw>
Save power when the bus is suspended by entering hibernation if
hibernation support is enabled and controller supports hibernation.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Add Power and clock gating control register to register map and
appropriate bit macros. Add missing GHWCFG4, GLPMCFG and GPWRDN bits.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Add barrier between triggering Capture task and reading CC as otherwise
it is possible that CC read will occur before task is triggered when
bus is busy.
Add barrier between reading previous CC value and writing the new one.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
add driver for Monolithic Power Systems MPM54304 with basic
functionality to enable/disable the buck regulators
Signed-off-by: Elias Speinle <e.speinle@vogl-electronic.com>
Updated condition to enable NET_STATISTICS. Changed
CONFIG_NET_STATISTICS_ETHERNET to CONFIG_NET_STATISTICS_WIFI
in airoc_wifi.c
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
With ACE2/3 the HDA DMA includes registers to read the Linear Link
Position.
Previous platforms (CAVS, ACE1) was able to report the LLP for GPDMA. Since
ACE2 all links are handled with HD-DMA, hence the new register has been
added for the firmware to report the LLP to the host.
Set the total_copied to 0 for older ACE1/CAVS platforms and in case of
host DMA on ACE2/3 since the informatiojn is not available.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Fixes: #77705
Fix wrong macro.
Tested with all the boards mentioned in that issue, build now works.
Signed-off-by: Sergio R. Caprile <scaprile@gmail.com>
Add a mode to build the driver without FW blobs, this is mainly for
twister to run and catch any build issues without depending on any FW
blobs.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Enable CYW20829_BT_FW_TX10DBM_POWER by default to get
best user experience experience out of the box.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Added setup of PUBLIC ADDR
NOTE: By default, the CYW208xx controller sets some
hard-coded static address.
To avoid address duplication, let's always override
the default address by using the HCI command
BT_HCI_VND_OP_SET_LOCAL_DEV_ADDR. So
1. when cyw208xx_setup gets BT_ADDR_ANY from the host,
it will overwrite the default address, and the host
will switch to using a random address (set in the hci_init
function).
2. If user set the static address (by using bt_id_create)
before bt_enable, cyw208xx_setup will set user defined
static address.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Select PAwR if enabled following features:
- BT_PER_ADV_RSP
- BT_PER_ADV_SYNC_RSP
Remove dependency BT_AIROC_CUSTOM for AIROC_CUSTOM_FIRMWARE_HCD_BLOB
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
When using the it8xxx2bx chip, because the SRAM size is 60k and
not a power of 2, using (CONFIG_SRAM_SIZE - 1) results in an
incorrect value for the h2ram base address mask.
Therefore, the mask is declared as GEMASK(19, 0) here.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
DMA_INTEL_ADSP_HDA_TIMING_L1_EXIT should be set by default
for all Intel ACE platforms
Signed-off-by: Adrian Bonislawski <adrian.bonislawski@intel.com>
Tmr and dtmr drivers were missing a flag which tells the
counter_is_conting_up function that the counter is counting up. So I've
added the flag
Signed-off-by: Krystof Sadlik <krystof.sadlik@nxp.com>
Due to it is a normal firmware downloading sequence,
it should be a debug log instead of error log.
Change LOG_ERR to LOG_DBG for this case.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Extend the adc_mcux_adc12 adc api to set the ref_internal to
a value of vref-mv property.
Signed-off-by: Marcin Wierzbicki <marcin.wierzbicki@accenture.com>
Enable support for channels >= 16 on devices S32K146 and S32K148.
Channels >= 16 are encoded as 100000b..101111b in SC1[ADCH] field.
Signed-off-by: Marcin Wierzbicki <marcin.wierzbicki@accenture.com>
Update Ambiq adc driver to add apollo4
fixed typ of BUMBER to NUMBER
Move buffer size prio to configuring slots
and enabling the ADC
removed #if defined(CONFIG_PM_DEVICE_RUNTIME)
Signed-off-by: Richard Wheatley <richard.wheatley@ambiq.com>
Add driver support for Bosch bmp180 pressure sensor running on i2c bus.
It pushes the driver files to the bmp180 directory under
drivers/sensor/bosch. The driver implement the Sensor API
and support channel DIE_TEMP and PRESSURE.
Driver had been tested with the NRF5340DK.
V2 fixup
---------
Drivers: Bosch bmp180 fixups for PR v2
fix BMP180 in CMakeLists.txt
rename regControl to ctrlreg
simplify the logic in set_attribute
use BMP180_GET_CMD_TEMP_DELAY
Drivers: Bosch bmp180 use system byteorder macros
To aware of ENDIANESS use the macros from byteorders.h
Drivers: Bosch bmp180 comments added to #endif
Add a comment to the #endif /* CONFIG_FOO */
Drivers: Bosch bmp180 , fix twister run error
twister report an error related to using floor() with a float
fix this using floorf() function.
Drivers: Bosch bmp180, rework review v2
fix code style issues
simplify the structure for bus and i2c.
prepare to remove the empty bmp180_i2c.c
Drivers: Bosch bmp180, remove bmp180_i2c.c
bmp180: update CMakeList.txt remove bmp180_i2c.c
bmp180: remove unused variable
fixups for complient checks
replace homebrew bitshift with byteorder.h macro
sys_get_be16 and sys_get_be24
cleanup remove unused spi.h
change struct reg16/24 to uint8_t[]
remove channel AMBIENT_TEMP
bmp180/Kconfig add missing help text
fix indent issue in bmp180_pm_action
merge BMP180_CONFIG_I2C into BMP180_INST
Move DT_DRV_COMPAT out of the header file
drop LOG_DBG() from read calibration data
remove bus_io implementation and header cleanup
move headers and structs out from bmp180.h
fix typo in comment
apply clang format changes, only if not line lenght violation
fix indent code error after joined lines
conversion from Pa to kPh was wrong, fixed it
Remove default=n from Kconfig, it is the default.
Move the conversion ready test into a function (duplicate code)
and apply retry policy
parameter naming with indicate the usage
change BMP180_INST(inst) to clang format
fix int32_t overflow in convension formular
fix wrong devider in convension formula
move BSWAP_s16 BSWAP_u16 from .h to .c
Signed-off-by: Chris Ruehl <chris@gtsys.com.hk>
Now that there is an actual Kconfig symbol generated for blobs presence,
take advantage of that and declare appropriate dependencies to it. Also add
helpful CMake output if the blobs are missing by taking advantage of the
zephyr_blobs_verify() CMake function.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
Modify the function "i2s_stm32_set_clock" to handle the case where pclk_len
it is not greater then 1 and to ensure that the freq_in
variable is correctly set in both cases.
Signed-off-by: IBEN EL HADJ MESSAOUD Marwa <marwa.ibenelhadjmessaoud-ext@st.com>
1) After the wifi driver successfully connects to the AP,
the dormant state should be set to OFF.
Once a deauth/disassoc frame is received or link lost occurs,
the dormant state should be set to ON.
2) Enable CONFIG_NET_TC_SKIP_FOR_HIGH_PRIO and CONFIG_NET_CONTEXT_PRIORITY
to push high priority packets directly to network driver.
Signed-off-by: Gang Li <gang.li_1@nxp.com>
The STM32H5x adc has a special option register that
needs to be set when using channel 0 on adc1.
fixes: #77618
Signed-off-by: Lars Jeppesen <lje@foss.dk>
The gen_kobject_list.py script expects the __subystem declaration to end
with _driver_api. Adjust the stepper api and existing driver implementation
accordingly.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Some hardware configuration require rely on the ALERT/RDY
pin to know when and ADC conversion is completed.
The polling thread is left as fallback, when the pin
is not defined.
Signed-off-by: Efrain Calderon <efrain.calderon.estrada@gmail.com>
For mapping operations in sys_mm_drv_simple_map_region() and
sys_mm_drv_simple_map_array(), when there was an error with
mapping any pages, it would simple return an error, leaving
already mapped pages still mapped. This modifies the behavior
where any failure during the whole mapping operation will
unmap the already mapped pages.
This also modifies the remapping and moving functions to
reset mappings when error is encountered.
Fixes#73121
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Adds the use of generic touch reporting method for stmpe811 driver.
Signed-off-by: Dominik Lau <dlau@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Adds the use of generic touch reporting method for ft5336 driver.
Signed-off-by: Dominik Lau <dlau@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Adds a way of reporting touchscreen events
taking common properties into account.
Signed-off-by: Dominik Lau <dlau@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
This transforms the existing driver for the Microchip MCP9808
to be used as a generic driver to be used with all
JEDEC JC 42.4 compliant temperature sensor chips.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
The "channels-num" should not be used here, other system's parts are using
"channel-count" instead for the same purpose.
Also property's description has been сorrected.
Signed-off-by: Andrey VOLKOV <andrey.volkov@munic.io>
Add overrun count in statistics. It will represent
the number of packets dropped either at received and
sent due to lack of buffer memory.
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
Remove water mark configuration and handle its interrupt
instead, since it is only present in ESP32S3.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
When omitting the clk_src definition in a child node of a pclkblock,
it uses the source of the parent node.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Allows MSTP register addresses to be changed in the device tree
to support different configuration SoCs.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Add support for HSE as the RTC clock source.
The initial implementation has the following limitations:
- Only whole MHz HSE frequency is supported, e.g. 24.5 MHz will generate a
compile error.
- Frequencies equal or above 64 MHz are not supported and will generate a
compile error.
The implementation has been tested on nucleo_h563zi with:
- 8 MHz (via hse-bypass)
- 25 MHz (via external crystal)
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
After testing the flexio spi_loopback on the ke1xz platform,
it is found that the master transfer and receive are not
synchronized. So add loop code to wait for the master transfer
to complete for frdm_ke17z and frdm_ke17z512 platforms.
Signed-off-by: Anke Xiao <anke.xiao@nxp.com>
Adds support for setting the operating mode of the TMP116/7 sensor to
either shutdown, continuous conversion or one-shot mode.
Signed-off-by: Ian Morris <ian.d.morris@outlook.com>
- Allow setting polarity from DT.
- At least on bcf, going from 0 to 255 causes brightness to decrease
(although 0 is still off and 255 is still on).
- Seems to work as expcted by using TnPWML register.
Signed-off-by: Ayush Singh <ayush@beagleboard.org>
TX/RX FIFO underrun shouldn't crash the RTOS when it occurs.
Also, since this can also happen under "normal" conditions
(i.e: DMA doesn't copy data fast enough from/to SAI's FIFOs)
the software should be able to recover from it.
As such:
1) Remove `z_irq_spurious()` call.
2) Clear error flag
3) De-escalate error message to warning message
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
This commit rebrands the STM32 EXTI API to a more hardware-agnostic
"GPIO interrupt controller" API, in anticipation of the introduction of
new series lacking the EXTI peripheral. The GPIO and EXTI drivers are
updated to match the rebranded API.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
This commit makes the contents of the stm32_exti_line_t data type opaque to
the EXTI GPIO interrupt controller API users. The GPIO driver is updated
to comply with this API change.
N.B.: while some assertions are removed as part of this commit, they were
broken since forever anyways, so nothing of value is lost.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Move the functions that interact with EXTI configuration registers to
select or get the GPIO port that triggers events on a given EXTI line
to the EXTI driver.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Modify all functions in the GPIO driver that interact with the EXTI
so that names, signatures and comments match what they do better.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Use the `gpio_pin_t` type for all variables that hold a pin number (0..15).
Change all `int` to `uint32_t` instead, as signedness is unwanted.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
This commit reorders the functions in the EXTI driver.
Internal functions and exported functions are now grouped with each other.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
This commit changes the EXTI driver API to use unsigned types
for all parameters previously typed as `int`, as the signedness
is unneeded and unwanted.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
All assertions performed in the EXTI drivers were wrong, as they passed
values to __ASSERT_NO_MSG instead of predicates. Update all assertions
to be actually useful.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
The EXTI driver API defined in exti_stm32.h is reserved for exclusive usage
by the STM32 GPIO driver, which doesn't use this macro. Since there is no
usecase for it anyways, it can be removed for future-proofing.
The STM32 UART driver is an unintended user of this definition, however.
Replace it with a private #define which is more appropriate anyways.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
apollo3 driver added PM to UART for only apollo3
but defined PM function for both causing an error
in twister
Signed-off-by: Richard Wheatley <richard.wheatley@ambiq.com>
Automatically handle device runtime PM for all flash API calls.
Asynchronously release the device after a small delay to minimise power
state transitions under multiple sequential API calls (e.g. NVS).
Signed-off-by: Jordan Yates <jordan@embeint.com>
Remove `SPI_NOR_IDLE_IN_DPD` to simplify the possible transition states
in the `spi_nor` driver. This option was originally added 5 years ago
when device runtime PM was in a much less mature state.
I do not believe having a separate power management implementation for
this one in-tree driver is in the interests of the project.
The behaviour of `SPI_NOR_IDLE_IN_DPD` leads to extremly suboptimal
behaviour in use cases where multiple small reads are performed
sequentially, see #69588.
Removal of this option does not break the behaviour of any existing
applications, only increases current consumption in idle by ~10uA until
device runtime PM is enabled.
Signed-off-by: Jordan Yates <jordan@embeint.com>
A 16-bit value built using byte shifts and ORs from a given
couple of lsb and msb bytes will result to be the same on both
little-endian and big-endian architectures, e.g.
uint8_t lsb, msb;
int16_t val;
/* val is the same number on both le and be archs, but has
different layout in memory */
val = (msb << 8) | lsb;
All the xyz_raw_get() APIs of stmemsc sensor module build the sensor
data using the above method and DO NOT hence require (it actually leads
to wrong values on big-endian machines) to use any le/be swap routines,
such as sys_le16_to_cpu().
Fix#75758
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Updated the counter_mcux_lptmr driver to support multiple
instances of the lptmr peripheral. Also added a new
binding property to identify if the user is using
counter-mode or pulse mode. since we were previously using the
prescaler value to check this which could be wrong
if used as a division value for getting the freq.
Added a property that allows the user to decide
what the counter value in lptmr should be divided by.
Cleaned up INIT macro for lptmr.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
The reset function uses uint32_t as its 2nd parameter, which leads to the
following compiler warning.
zephyr/drivers/mipi_dbi/mipi_dbi_stm32_fmc.c:176:18: warning:
initialization of 'int (*)(const struct device *, k_timeout_t)' from
incompatible pointer type 'int (*)(const struct device *, uint32_t)'
{aka 'int (*)(const struct device *, unsigned int)'}
[-Wincompatible-pointer-types]
176 | .reset = mipi_dbi_stm32_fmc_reset,
| ^~~~~~~~~~~~~~~~~~~~~~~~
When you look at similar drivers,
/drivers/mipi_dbi/mipi_dbi_smartbond.c#L126
/drivers/mipi_dbi/mipi_dbi_nxp_lcdic.c#L561
you notice they use k_timeout_t.
So the whole fix is to correct the type.
Signed-off-by: Thorsten Spätling <thorsten.spaetling@vierling.de>
Remove the early max packet size check on endpoint activation, because
there are valid use cases where the max packet size is not multiple of 4
and the stack won't perform multi-transaction transfers. Example use
case is UAC2 explicit feedback endpoint that has Max Packet Size equal
3 when device is operating at Full-Speed.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Fail TxFIFO write if the endpoint is not activated, because there is
essentially no fifo assigned. Writing to not activated endpoint is
possible, but it does tend to corrupt fifo number 0 which is used for
control transfers. USB stack should not really be attempting to write to
endpoints that have not been activated (ep_enable called).
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Store SOF frame number and use the information to set the Even/Odd
microframe bit when enabling isochronous endpoints. Reject received
isochronous data if number of packets received does not align with
received PID.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
RxFLvl interrupt should only handle the actual data movement from RxFIFO
to the buffer. OUT transfers are completed in XferCompl handler both in
DMA and Completer mode. This reduces code size by avoiding having
separate code paths based on operating mode.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Function dwc2_set_dedicated_fifo() calls dwc2_flush_tx_fifo() before the
diepctl register is written. The register will be only written after the
dwc2_set_dedicated_fifo() finishes. Solve the problem by passing fifo
number directly instead of endpoint address to dwc2_flush_tx_fifo().
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Add all register bit defines necessary for isochronous transfers. Clean
up the endpoint transfer size register defines clearly separating IN and
OUT registers because they do use different bit fields. Add alternate
bit names for bits that do have different meaning based on configured
endpoint transfer type.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Reset delay was not being calculated correctly in lcdic driver, the
ticks field needs to be accessed directly within the timeout structure
to calculate the correct delay time
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The driver in tree is for u-blox M8 devices, not M10. The M10 series
devices (from Protocol Version 23.01) use a different, non backwards
compatible interface for configuring the modem behaviour.
Of the two boards tested in the original PR, the "VMU RT1170" is
explicitly listed as having a u-blox NEO-M8N modem, while I have
been unable to find any information online about the "FMURT6" board.
Leaving the naming as-is will cause problems when M10 drivers are
contributed.
Signed-off-by: Jordan Yates <jordan@embeint.com>
- Removed zero initialization of `pincfg` structure as all members
are guaranteed to be set.
- Introduced `pfs_cfg` as an intermediate variable to store data in
the CPU register instead of stack.
- Simplified pin setting logic by relying on `pfs_cfg` being
zero-initialized, eliminating the need for explicit bit clearing.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Add power management support to various drivers:
- gpio-kbd-matrix
- ite,it8xxx2-kbd
- nuvoton,npcx-kbd
- microchip,xec-kbd
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add power management support to the keyboard matrix library. This
provides a generic pm_action function that changes the keyboard matrix
scan in two places when suspended:
- reset the state to 0 for all columns
- do not enable key press detection
This ensures that any key that was pressed when the device is suspended
is released, and no other scan happens until the device is resumed.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This is just the driver for banks 0 to 3. Bank 4 will come via a
separate commit since it needs a different driver.
Signed-off-by: Michael Zimmermann <michael.zimmermann@grandcentrix.net>
This serves two main purposes:
- change the CPU clock via devicetree nodes
- provide the APB frequency to device drivers via the clock driver
interface
Theoretically this could also support choosing between the available
clock sources, but right now we only support LPOSC0 going into PLL0,
going into AHB.
Turning the PLL back off is also not supported since the only current
use case is to set the PLL frequency, turn it on, and switch the AHB
over to it.
Signed-off-by: Michael Zimmermann <michael.zimmermann@grandcentrix.net>
Can be used only once the SiM3U SoC support has been added.
Developed-by: Michael Zimmermann
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
For applications that rely on low noise/variance in accelerometer
sample reading. Application can take advantage of integrated LPF
Thus this PR adds LPF configuration capability to the mc3419 driver
Signed-off-by: Anuj Pathak <anuj@croxel.com>
Reuse the file clock_stm32g0.c for the STM32U0 and
rename it to clock_stm32g0_u0.c
because the G0 and U0 series share the same clock control.
Signed-off-by: IBEN EL HADJ MESSAOUD Marwa <marwa.ibenelhadjmessaoud-ext@st.com>
SOF is designed with the idea that the data transfer
between the host memory and local memory is performed via
DMA. This is not true for imx platform in which the DSP
performs this operation.
Because of the aforementioned design, SOF performs a
cache invalidation operation on the destination memory
region before data is copied further down the pipeline.
For some imx platforms, the destination memory region is
cacheable. As such, some of the data transferred from the
host memory region is held entirely in cache, which means
the RAM and the cache have different data for the same
memory region.
In such cases, performing cache invalidation forces
the DSP to fetch data from RAM instead of the cache, which
means the DSP will read stale data and propagate it further
down the pipeline.
Although not optimal and mostly as a workaround to this issue,
perform a cache WB operation on the destination memory region
to make sure that the cache and the RAM hold the same data.
During the data read operation (to copy it further down the
pipeline) after the aforemention cache invalidation, the DSP
will no longer end up reading stale data.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
When CONFIG_RISCV_VECTORED_MODE is disabled, CLIC claims interrupts using
CSR 'mnxti' and handles all pending interrupts before exiting the ISR.
When CONFIG_RISCV_VECTORED_MODE is enabled, all interrupts use vector mode
and are claimed automatically. The RISC-V common ISR is used for interrupts
hooked into SW ISR table, but it only handle one pending interrupt per ISR.
This commit enhances CLIC to set vector mode for direct ISRs only and use
the CLIC common entry for regular ISRs to handles multiple pending
interrupts in an ISR.
Signed-off-by: Jimmy Zheng <jimmyzhe@andestech.com>
Introduce riscv_clic_irq_vector_set() to implement z_riscv_irq_vector_set()
for CLIC. This commit also introduces CONFIG_CLIC_SMCLICSHV_EXT to indicate
support for the smclicshv extenion and riscv_clic_irq_vector_set().
Signed-off-by: Jimmy Zheng <jimmyzhe@andestech.com>
Most of BT_FOO symbols that are designed to select the hci driver
implementation which will drive the comunication with controller are
selected based on device tree compatible and should not be made available
as an configurable option to the user.
To do this, remove the prompt on these symbols.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
The current video drivers did not allow VIDEO_EP_ALL to be selected,
as used by video_stream_stop().
This adds the VIDEO_EP_ALL to each video driver that filtered endpoints.
Signed-off-by: Josuah Demangeon <me@josuah.net>
- Slightly improve the name of this kconfig adding the suffix
_POLL in order to highlight that this adds a callback
function used to poll data.
- Description was also updated to point out that this symbols
might not only use the (secure) entropy driver, but also
generic number generators, some of which are not really
secure.
- The symbol was move from Kconfig to Kconfig.tls-generic because
this is where MBEDTLS_ENTROPY_C is located and since
MBEDTLS_ENTROPY_HARDWARE_ALT depends on the former (it only
makes sense if the entropy module is also enabled), we add
also the "depends on".
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
ENABLED suffix does not really makes much sense for a kconfig
so it should be removed. Also other MBEDTLS symbols were recently
updated accordingly.
Moreover having it named exactly the same way as in Mbed TLS
symplifies the understanding of what this kconfig is doing.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Fixes division by zero exception when SPI is configured to operate in mode3
whit CS controlled by software.
Such exception occurred because data->dfs is listed as the denominator in
a division inside the spi_esp32_transfer() function which is called from
spi_esp32_configure() (before assigning a value to data->dfs) inside
transceive() in the condition where mode 3 is chosen as the SPI operating
mode and the chip select is configured to be software-controlled.
Signed-off-by: Marcio Ribeiro <marcio.ribeiro@espressif.com>
Run clang-format on drivers/led/lp5569.c to align formatting in the file.
No functional changes intended.
Signed-off-by: Emil Dahl Juhl <emdj@bang-olufsen.dk>
The lp5569 features a double functioning pin for enable and pwm control.
The chip, however, uses the first rising edge to initialize and get ready
for i2c communication, and then the pin alters function to pwm mode.
Add support for providing enable-gpios to the lp5569 in the dts, which
will make sure to assert the pin and wait for the chip to initialize
before attempting further configuration of the chip.
Signed-off-by: Emil Juhl <emdj@bang-olufsen.dk>
The lp5569 controller contains an internal charge pump which can be useful
for driving LEDs with a forward voltage greater than the lp5569 supply.
Taking advantage of the charge pump can alleviate the need for an external
boost converter.
Add a dts property, charge-pump-mode, to the ti,lp5569 binding with which
the cp_mode bits of the MISC register will be configured.
Following the datasheet, the possible configurations are:
0x00 -> disabled (default)
0x01 -> 1x mode
0x10 -> 1.5x mode
0x11 -> auto mode
Signed-off-by: Emil Juhl <emdj@bang-olufsen.dk>
Route `configure` and `recover_bus` through the RTIO framework to avoid
race conditions. Update `RTIO_OP_I2C_RECOVER` implementation to actually
recover the bus, instead of triggering a loop.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Incorrect value set by user when using sensor_attr_set can fail silently
since it always returns 0.
Fix by adding ret. Also added return on sensor_attr_get.
Signed-off-by: Aiman Mazlan <mohammad.aiman@stratusauto.com>
Fixes the adxl345 accelerometer driver to return zero on sample fetch
success, as specified by the sensor driver API. Prior to this change,
the driver incorrectly returned a positive non-zero value on sample
fetch success, which in turn caused a bus fault getting data with the
sensor shell.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Add checks to return value of esp_intr_alloc to avoid drivers init
returning 0 when interrupt allocation fails.
Signed-off-by: Raffael Rostagno <raffael.rostagno@espressif.com>
Initial commit for entropy support on RA8
- drivers: entropy: implementation for TRNG driver of RA8x1
- dts: arm: add device node for trng of RA8x1
- boards: arm: enable support zephyr_entropy for ek_ra8m1 and
update board documentation
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
Signed-off-by: Duy Phuong Hoang. Nguyen <duy.nguyen.xa@renesas.com>
Monitor mode relies on core Wi-Fi management functions, so, the file
should be included for both system and system with raw modes.
Fix this by adding a hidden symbol.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
If Wi-Fi management is enabled, then independent of modes scan
functionality is always included.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
This is a fix from QSPI-NOR driver to wait for clock divider change to
be applied and take effect.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
For less than 32MHz using HFCLK192M, /2 divider should be used and only
for Anamoly159 /1 divider should be used.
Without this fix 8MHz clock in DTS uses 16MHz clock.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
SHEL-2947] Option to set either PS-poll or QoS null frame based
power save data retrieval mechanism.
Signed-off-by: Ajay Parida <ajay.parida@nordicsemi.no>
Removes the requirement for the different layers in the OS agnostic
parts of the driver having to maintain a handle to the OS interface
layer in order to call the OS interface calls. The OS interface layer
now maitains the handle to OS-specific ops internally and invokes the
appropriate functions.
Fixes SHEL-2639
Signed-off-by: Sachin D Kulkarni <sachin.kulkarni@nordicsemi.no>
[SHEL-2542] When reset command is called this will
reset all statistics including firmware and host.
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
[SHEL-2054] Adding a kconfig option for WMM.
By default it will be enabled. If user needs
to disable it, set it as n.
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
1. tm_mon in rtc_time structure has a range [0, 11],
while the RTC expects [1, 12]. Add missing
increasing / decreasing of this value.
2. Fix typo in debug log
Signed-off-by: Daniel Kampert <DanielKampert@kampis-elektroecke.de>
The imx USDHC driver previously queried the peripheral's internal card
detect signal to check card presence if no card detect method was
configured. However, some boards do not route the card detect signal and
do not work correctly with the DAT3 detection method supported by this
peripheral. As a fallback, assume the card is present in the slot but
log a warning to the user.
Fixes#42227
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Move default of monolithic and fw loader, options, etc to the
common kconfig files rather than defaulting in soc file.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
The CONFIG_USB_MCUX_CONTROLLER_TYPE choice config
is not necessary, let's just remove it. Theoretically,
if there was an SOC with the EHCI and LPCIP3511, then
it might cause a build error, but there is no SOC
which is supported on this legacy driver that has that.
Remove all settings of it in the SOC files.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Move all dependencies of the family config to series level,
and put a disclaimer saying not to use the family config.
Change all occurrences of the family config in code to the
MCXNX4X series config.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Some flash/memc drivers like flexspi will want to default the
value of the log level to off to avoid RWW hazard while XIP,
to do this, the logging template must be sourced after the driver
kconfig files so that the default value from the driver is able
to be checked, since logging template introduces an unconditional
default otherwise.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Introduced `GPIO_DEVICE_INIT_RA_IF_OKAY` which utilizes `COND_CODE_1`
to reduce the chain of #if DT_NODE_HAS_STATUS(...) #endif
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Build was failing due to const variable being passed as function param
accepting non-const variable discarding const qualifier. Explicitly cast
to fix the build issue.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
The ESAI is already reset during the config_set() function
so no need to also reset it during init().
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
The reset pin on the chip is optional, add a soft reset call when the
reset pin is not specified for the device.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Removes calling k_busy_wait() and uses k_msleep().
Updates polling rate of EEPROM busy status after read request to 1 ms, as
recommended by the app note.
Signed-off-by: Jakub Topic <jakub.topic@anitra.cz>
Align all sensor drivers that are using stmemsc (STdC) HAL i/f
to new APIs of stmemsc v2.6
Requires https://github.com/zephyrproject-rtos/hal_st/pull/21
Signed-off-by: Armando Visconti <armando.visconti@st.com>
set high_bandwidth and use the cfg->mps to set
ep_init.maxPacketSize because NXP MCUX controller
driver supports additional transaction bits in
maxPacketSize.
Signed-off-by: Mark Wang <yichang.wang@nxp.com>
Instead, use the helper to get the size field from the MPS value.
MPS value may contain information about additional transaction
per microframe (bits 12..11).
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
