Align the SPI init priority with other devices.
Other bus-devices like UART and I2C are init at standard kernel
device level (50), but SPI is at 70 and there appears to not be
a reason for it.
GPIO is init at 40 so there should not be an issue to use the default.
Signed-off-by: Joakim Andersson <joerchan@gmail.com>
This adds support for the GRLIB SPIMCTRL SPI controller used in LEON and
NOEL-V systems. SPIMCTRL can operate in two different modes: In the
default mode it allows memory-mapped read access to the flash data. When
set in the user mode, it can be used to generate SPI bus transactions.
Signed-off-by: Martin Åberg <martin.aberg@gaisler.com>
Add driver for the Microchip Polarfire SOC MSS SPI controller.
The interrupts of the MSS SPI are routed through PLIC(Platform level
interrupt controller).
Tested with generic spi-nor flash driver(spi_flash) with both Fixed
flash configuration and Read flash parameters at runtime(using SFDP).
Signed-off-by: Naga Sureshkumar Relli <nagasuresh.relli@microchip.com>
Add a new SPI shim driver for Intel SoCs. Builds upon the SEDI bare
metal SPI driver in the hal-intel module.
Co-Authored-By: Kong Li <li.kong@intel.com>
Signed-off-by: Ye Weize <weize.ye@intel.com>
Initial version of Infineon CAT1 SPI Driver supporting synchronous
and asynchronous data transfer API
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
Add fundamental feature support for RP2040 PIO SPI peripherals.
This commit implements synchronous transfer with 8-bit MSB
format. Using PIO allows any GPIO pins to be assigned the roles
of CS, CLK, MOSI, and MISO.
Optional features not implemented yet:
- Interrupt based transfer
- DMA transfer
- Slave mode
- Varying word size
- 3-wire SPI support
- LSB-first
Updated in response to review comments.
Further updates from second round of review.
Rename spi_pico_pio.c source to match zephyr/MAINTAINERS.yml
Remove unnecessary initialization code.
Resolve merge conflicts
Signed-off-by: Steve Boylan <stephen.boylan@beechwoods.com>
This CL attempts to implement npcx's flash driver instead of the
original one (npcx spi driver plus spi_nor flash driver).
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add driver for OpenTitan SPI host.
Tested and verified single SPI full duplex on opentitan_earlgrey in
Verilator.
Signed-off-by: Shawn Nematbakhsh <shawn@rivosinc.com>
This adds the SPI driver for the Renesas SmartBond(tm) DA1469x MCU family.
The driver only supports controller mode. All four SPI modes are supported.
Note that the lowest supported speed is 2285714Hz.
Requesting speeds higher than 16MHz, will result in a 16MHz SCLK.
Co-authored-by: Stan Geitel <stan@geitel.nl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
Provides a macro and submit API for SPI drivers to support RTIO.
A copy function enables compatibility with the existing blocking API
and very easily the existing async API as well.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Unify the drivers/*/Kconfig menuconfig title strings to the format
"<class> [(acronym)] [bus] drivers".
Including both the full name of the driver class and an acronym makes
menuconfig more user friendly as some of the acronyms are less well-known
than others. It also improves Kconfig search, both via menuconfig and via
the generated Kconfig documentation.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add MEC172x full duplex qmspi driver version to support full
duplex transfers as expected by the Zephyr spi driver model.
On every spi clock we transmit one bit and receive one bit.
This driver will work with Zephyr SPI NOR driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add fundamental feature support for PL022 SPI peripheral.
This commit implements synchronous transfer with 8bit-MSB format.
Optional functions are not currently implemented yet.
- interrupt based transfer is not implemented yet.
- DMA transfer is not implemented yet.
- Slave mode is not implemented yet.
- Currently support only 8-bit data transfer.
Hardware limitation:
- LSB-first format is not supported by hardware.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
This patch adds driver for the Microchip Polarfire SOC MSS QSPI
controller.
The interrupts of the MSS QSPI are routed through PLIC(Platform level
interrupt controller).
Tested with generic spi-nor flash driver(spi_flash) with both Fixed
flash configuration and Read flash parameters at runtime(using SFDP).
Signed-off-by: Naga Sureshkumar Relli <nagasuresh.relli@microchip.com>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add driver for MEC172x QMSPI with local DMA(LDMA). The driver
support SPI asynchronous operation.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
This adds an spi master mode driver via bitbanged gpio. Only syncronous
transfers are implemented. Clock signal timing is accomplished via busy
waits, the gpios are manipulated via the standard gpio interface; these
two factors limit the frequency at which it can operate - but here
a simple and generic implementation was chosen over performance.
The driver supports the various clock polarity and phase
configurations, and can also work with word sizes which are non
multiples of 8bits, currently up to 16 bits.
A sample program is also added demonstrating basic use of the driver
with 9bit data words.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
This is meant to expose half/full duplex configuration option on regular
configuration. So far, dual/quad/octal are not exactly supported, as it
would require extensions to the SPI buffer for a full support.
So moving these modes to an extended operation attribute
(32 vs 16 bits), disabled by default.
And exposing half/full duplex configuration bit. Full duplex being the
default option.
Fixes#19134
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The FIU/UMA module in the NPCX chip provides an dedicated SPI interface
to access the SPI flash. This commit adds the driver support for it.
With this commit, the application can call the flash APIs
(via spi_nor.c) to access the internal flash of NPCX EC chips.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Change-Id: I32bbf09f6e014b728ff8e4692e48151ae759e188
With the introduction of `EXPERIMENTAL` and `WARN_EXPERIMENTAL` in
Zephyr all drivers settings having `[EXPERIMENTAL]` in their
prompt has has been updated to include `select EXPERIMENTAL` so that
developers can enable warnings when experimental features are enabled.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Instead of waiting forever for the SPI transfer to complete, let's use
a timeout value and bail out if elapsed. The timeout value logic is,
xfer_len/frequency + tolerance
Tolerance value can be modified using a Kconfig symbol,
CONFIG_SPI_COMPLETION_TIMEOUT_TOLERANCE. It defaults to 200ms.
Fixes: #33192
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Remove SPI_[0-8] and SPI_[0-8]_OP_MODES Kconfig symbols as no driver
uses them anymore. We also cleanup board and sample code to remove
use of these symbols.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We will need this to be able to DEVICE_DT_GET() bus devices from
tests/drivers/build_all in an upcoming commit.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add an emulation controller which routes SPI traffic to an attached
emulator. Only one emulator is supported per bus at present, since
chip-selction functionality is not present.
This allows drivers for SPI peripherals to be tested on systems that
don't have that peripheral attached, with the emulator handling the SPI
traffic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add SPI driver for the Xilinx AXI Quad SPI IP. Despite the name, this IP
block supports both single, dual, and quad line widths.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Same deal as in commit eddd98f811 ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for the remaining cases outside defconfig
files. See that commit for an explanation.
Will do the defconfigs separately in case there are any complaints
there.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit adds SPI driver and its bindings using the USART peripheral
for Silicon Labs EFM32 and EFR32 MCUs.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Adds a shim layer around the mcux lpc flexcomm driver to adapt it to the
zephyr spi interface. It leverages heavily from the existing mcux dspi
shim driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add SPI driver and bindings for LPSPI peripheral for the RV32M1 SOC.
Based heavily on the existing mcux LPSPI driver.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
Clean up space errors and use a consistent style throughout the Kconfig
files. This makes reading the Kconfig files more distraction-free, helps
with grepping, and encourages the same style getting copied around
everywhere (meaning another pass hopefully won't be needed).
Go for the most common style:
- Indent properties with a single tab, including for choices.
Properties on choices work exactly the same syntactically as
properties on symbols, so not sure how the no-indentation thing
happened.
- Indent help texts with a tab followed by two spaces
- Put a space between 'config' and the symbol name, not a tab. This
also helps when grepping for definitions.
- Do '# A comment' instead of '#A comment'
I tweaked Kconfiglib a bit to find most of the stuff.
Some help texts were reflowed to 79 columns with 'gq' in Vim as well,
though not all, because I was afraid I'd accidentally mess up
formatting.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
