It is possible that stm32_clock_control_init function is started
when the image is chain-loaded and hardware clocks are already
initialized to some state (PLL1).
Currently due to an assert in get_startup_frequency function
(which will trigger k_fatal_halt) the boot will stop on the
early stage if CONFIG_ASSERT=y. This is reproducible for example
with standalone MCUboot and TF-M with MCUboot.
Fixed by adding support for HSE and PLL1 clock sources at
get_startup_frequency.
Signed-off-by: Denis Mingulov <denis@mingulov.com>
BDCR and PWR_CR could be required for LSE or RTC for instance.
Enable it here as for now, no sophisticated PM handling is available
on F0 and F3 series.
Fixes#56449
Fixup for #56505
Signed-off-by: Kay P <kayo@illumium.org>
If clock frequency was already high and a ahb prescaler greater than 1
was used frequency could temporary become higher than allowed.
Signed-off-by: Benjamin Bigler <benjamin.bigler@securiton.ch>
Updated the code to to invoke reset using PCR block
z_mchp_xec_pcr_periph_reset() instead of resetting
using I2C Configuration register
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
New nrfx release brings change of Low frequency sources symbols
in nrf_clock hal to uppercase. This commit aligns all occurrences.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
If the boot loader already switched the system clock to PLL1 we need
to switch back to HSI first and disable PLL1 before we can configure
PLL1. Otherwise the register writes will simply be ignored and we'll
end up with an inconsistent state.
Most of the code has been recycled from `clock_stm32_ll_common.c`.
Signed-off-by: Sascha Silbe <sascha-pgp@se-silbe.de>
Signed-off-by: Sascha Silbe <sascha-pgp@silbe.org>
By default HSIDIV is set to 0x01, so default frequency is 32 MHz.
This register should be always set based on dts value.
Signed-off-by: Wojciech Slenska <wsl@trackunit.com>
The stm32f4 and stm32f7 serie has to compile the stm32_ll_rcc
layer to get the LL_RCC_GetSystemClocksFreq function.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
When ASAN is used cmd_status is kept, but it cannot be linked
as the shell module is not present, this prevents ASAN
being used with the nrf52_bsim.
Fix it by conditionally compiling this code only if the shell is
being used.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Remove all init functions that do nothing, and provide a `NULL` to
*DEVICE*DEFINE* macros.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The get_status api allows to query whether clock is turned on or off.
Like the get_rate call, the status of gated clocks (for specific
peripherals), as well as domain clock sources(HSE, PCLK, PLL_P,..)
can be checked this way.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
MISRA Rule 5.7 requires uniqueness of tag identifiers. Shell is
frequently problematic because many code uses `const struct shell
*shell`. This causes CI noise every time one of these shell files is
edited, so let's update all of them with `const struct shell *sh`
instead.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
BDCR could be required for LSE or RTC for instance.
Enable it here as for now, no sophisticated PM handling is available
on F3 series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
It was being included twice. Now it's included once. CI requires a commit
description.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
Without this, setting a value of 0 leaves the bits unchanged rather than
zeroing them.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
Add the driver for the clock control of the new stm32h5.
See the corresponding Ref Man to get the clock scheme :
HSI, CSI, HSI48, HSE, LSE, and 2 or 3 PLLs
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Unify the drivers/*/Kconfig menuconfig title strings to the format
"<class> [(acronym)] [bus] drivers".
Including both the full name of the driver class and an acronym makes
menuconfig more user friendly as some of the acronyms are less well-known
than others. It also improves Kconfig search, both via menuconfig and via
the generated Kconfig documentation.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add initial version of clock control for Atmel SAM SoC series. This add
support to Power Management which allows control peripherals clock.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The U5-series was missed when adding if-defs around enable / disable
of the backup domain access, this patch makes sure the U5-series
is handled correctly.
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
We get a compiler warning in this code with arm clang due to using
the wrong enum type for the variable. The enum should be of
type `enum periph_clk32k_src` so replace VBR_CLK32K_SRC_PIN_XTAL
with PERIPH_CLK32K_SRC_PIN_XTAL.
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
Add clock control support for UART controllers found in i.MX SoC family.
This change moves clock gating out of respective `soc.c` files and into
clock controller's `clock_control_on`/`_off` methods, allowing for
dynamic clock state control, and setup via Device Tree bindings.
This is especially important on SoCs, where Zephyr is sharing the bus
with cores running other OSes, such as might be the case for i.MX 8MM.
Unfortunately, Zephyr doesn't possess an ability to represent clock
hierarchy (e.g. via DT's `assigned-clocks` property), so clock source
and frequency still need to be hardcoded in aforementioned `soc.c`
files.
Signed-off-by: Artur Rojek <artur@conclusive.pl>
Use `uintptr_t` to cast a pointer to integer type for `clock_name`.
While at it, also remove an unused variable.
Signed-off-by: Artur Rojek <artur@conclusive.pl>
The STM32H730 series has a variant built with SMPS. It uses
`stm32h730xxq.h` header file instead of `stm32h730xx.h`, which has the
SMPS macro defined.
This commit adds the `SOC_STM32H730XXQ` configuration option to allow
the build system include the proper header file. With this change,
boards can enable `CONFIG_POWER_SUPPLY_DIRECT_SMPS` to set up the power
supply for the CPU.
Signed-off-by: Chen Xingyu <hi@xingrz.me>
Add clock rate definitions for MIPI and LCDIF peripherals, to enable
retrival of these peripheral clock rates at runtime.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add initial version of Infineon CAT1 clock control driver.
- supports clock initialization based on board DT configuration.
Added initial version of system_clocks.dtsi for Infineon PSoC 6 SOC.
Includes: clk_imo, path_mux0..4, fll0, pll0, clk_hf0..4, clk_fast,
clk_slow and clk_peri.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Add PLLI2S support within clock_control driver.
This implementation is compatible with "st,stm32f412-plli2s-clock"
binding.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add PLLI2S support within clock_control driver.
This implementation is compatible with "st,stm32f4-plli2s-clock"
binding.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This enables the MCO clock output pin to be configured through Kconfig on
stm32l4 devices.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
This enables the MCO clock output pins to be configured through Kconfig on
stm32f7 devices.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
Program the right trim control register for mec150x.
This fixes uart debug console output issue.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
On stm32wb, M0 core may enable and disable CLK48 when using RNG.
Lock related hsem to prevent M0 to disable CLK48 when it doesn't need it
anymore.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In some case, we may need to describe a domain clock for a device
while there is no way to configure it (ex: USB clock set on PLL_Q output
on F405 devices > It is not selectable).
Then, configuring a device clock domain in the clock_control driver
will allow to retrieve its subsys rate.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Current divisor is 10000000 (should be 1000000).
For example, ESP32_CLK_CPU_240M / 10000000 == 24 MHz (incorrect).
Signed-off-by: Chris Wilson <christopher.david.wilson@gmail.com>
ESP32 and ESP32-S2 HW clock are tied to DTS clock configuration.
This changes updates the default configuration to retrieve
this information from DTS.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Add support for Microchip MEC15xx to the XEC clock control driver.
MEC15xx 32KHz clock support uses the same 32KHz source for both the
PLL and peripherals. MEC152x does not include the PCR clock monitor
present in MEC172x. MEC15xx and MEC172x support internal silicon
oscillator, parallel and single ended crystal inputs, and the
32KHZ_PIN input. MEC152x supports fall back to internal silicon
OSC when VTR and 32KHZ_PIN are turned off. Therefore in MEC152x the
internal silicon oscillator can only be disabled if using an external
32KHz which is always on. For MEC152x the driver will only use the
PLL source clock device tree value.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Fix Microchip XEC clock control driver single-ended XTAL2 pin
initialization. Add support for external 32KHZ_IN pin as a
clock source including PINTRL to switch the GPIO to 32KHZ_IN
function. Add device tree option to disable internal silicon
oscillator if it is not required by the configuration. Add
device tree tuning options based on crystal and board layout.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
On STM32F1 series, configure USB(/OTGFS) prescaler based on DT.
When prescaler is set, PLL output clock is not divided.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The timer_ids contain timers that belong to any bus.
So, It should recognize with entire id, not only the CLOCK_ID_BIT part.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
DT_COMPAT_GET_ANY_STATUS_OKAY is not suited for the node's existing check.
(This macro returns the stem of the DTS macro name,
the stem part is not a defined symbol.)
Instead, it should use the DT_HAS_COMPAT_STATUS_OKAY macro.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
For the stm32 devices that have a HSI48 clock,
the driver enables it, like any other fixed clock,
if needed and supported by the serie.
For stm32L0, SYSCFG VREFINT is also required.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The stm32_clock_control_init is needed for implementation of custom
pm_state_exit_post_ops.
Signed-off-by: Artur Lipowski <Artur.Lipowski@hidglobal.com>
Routines called by users to release (and perhaps stop) the HFCLK
cannot synchronize with only the `hfclk_users` atomic variable,
because a thread can be preempted right after it clears the proper
bit in that variable but before the HFCLK is actually requested to
stop, and another user can then request the HFCLK to start. This can
result in HFCLK being stopped right after it was requested to start
and in `hfclk_users` holding an incorrect value.
Fix this by locking interrupts in those routines until the HFCLK is
stopped.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The Flash latency depends on the sysclock
In case of the stm32F7 the regulator overdrive mode is set
depending on the sys clock freq.
The overdrive must be set before the first LL_SetFlashLatency.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
With the stm32U5, when the sysclock is > 55 MHz, the EPOD booster
must be configured before the PLL1 is enabled (see refMan).
This is the case when sysclock is on PLL1 sourced by MSIS or
HSE higher than 16MHz.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
In order to configure domain clock, clock_control_configure should be
used instead of clock_control_on which is only useful for bus clock gating.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Microchip MEC172x CPU and fast peripheral (QMSPI and PK) are
clock source is based upon an OTP setting. Add logic to adjust
clock source based on OTP value. If the OTP value is ever changed
this fix will allow calcluation of correct clock rate.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
clock_stm32_ll_common.h was missing <stdint.h> and <zephyr/device.h>. It
turns out things worked because <zephyr/init.h> has a forward
declaration of struct device.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Change automated searching for files using "IRQ_CONNECT()" API not
including <zephyr/irq.h>.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
mcux HAL pollutes namespace with stuff like ARRAY_SIZE, MIN, MAX, etc.
Luckily it only defines them if not already defined, so we can play with
include order to "fix" the problem. Move the infamous soc.h (which
includes HAL) after other Zephyr includes.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Some files using time_units.h API did not include it, e.g. for
sys_clock_hw_cycles_per_sec.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The sys* ops like sys_clear_bit are indirectly included via arch CPU
header. Other stuff like find_msb_set end up included via this header as
well.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use the FSL_FEATURE_MCG_FFCLK_DIV define to decide if we should
call the api to get Fixed Frequency Clock.
This fixes Issue #49924
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
This adds a very basic driver to utilize the I3C IP block
on MCUX (e.g. RT685). Note that, for now, this only supports
being the active controller on the bus.
Origin: NXP MCUXpresso SDK
License: BSD 3-Clause
URL: https://github.com/zephyrproject-rtos/hal_nxp
Commit: 2302a1e94f5bc00ce59db4e249b688ad2e959f58
Purpose: Enabling the I3C controller on RT685.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
DT node "st,stm32f105-pll2-clock" already exists but was not actually used
and PLL2 was not being configured.
PLL2 is available on STM32F105/F107 and should be turned off after turning
off PLL and turned on before turning on PLL again since PLL2 can be
used as a source for PLL. Source for PLL2 is always HSE.
Signed-off-by: Pierre-Emmanuel Novac <piernov@piernov.org>
On some stm32 mcus, the LSE is enabled as system clock (LSESYS)
only when the LSEON and LSERDY are both set.
The bit LSESYSEN is set in the RCC BDCR register
and the driver is waiting for the LSESYSRDY to be set.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add R-Car Gen3 PWM driver.
Clock diviser is automatically adjusted according to requested period
and duty-cycle in order to obtain as much accuracy as possible.
Indeed, in order to improve PWM accurancy, the PWM clock has to fit
the requested period. So use the given period_cycle to define if the
clock as to be adapted. In such case, increase/decrease the clock
diviser to adapt the period_cycle and be sure that it fits into the
10 bits counter of the PWM controller.
Tested on H3ULCB on pwm0 and pwm4.
Signed-off-by: Pierre Marzin <pierre.marzin@iot.bzh>
MCO1 is also available on STM32F1 series (on top of STM32F4), allow
selection of MCO1 source with CLOCK_STM32_MCO1_SRC_* Kconfig parameters.
Available MCO1 sources are slightly different between STM32F4
(LSE, HSE, HSI, PLLCLK) and STM32F103 (HSE, HSI, PLLCLK/2, SYSCLK), and
STM32F105/F107 have a few more (EXT_HSE, PLL2CLK, PLLI2SCLK, PLLI2SCLK/2).
MCO1 on STM32F1 does not have a configurable divider (unlike STM32F4),
HAL call only configures source.
STM32F1 do not have MCO2.
Signed-off-by: Pierre-Emmanuel Novac <piernov@piernov.org>
This patch adds a clock control driver for GD32 platforms. It is
important to note that the driver is only able to handle peripheral
clocks, but not "system clocks" (e.g. PLL settings, SYS_CK, etc.). On
some similar platforms (STM32) this task is embedded in the same clock
driver, performed at init time but with no options to do any
manipulation at runtime via the API calls. The clock control API as-is
is really orthogonal to "system clocks", and it is arguably a bad idea
to embed system clock init code in a clock control driver. It can be
done at SoC level still using Devicetree as a source of hardware
description/initial configuration.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
soc.h has been removed for ARM64 SoC platforms and it is also needed by
ARM32, so remove it from related drivers.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Add device specific clock initialization, which uses
reset reason cause information to proper define
peripherals clock state.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
prev_temperature was only used if USE_TEMP_SENSOR is true. Make its
definition conditional.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The temperature sensor was only needed when
CONFIG_CLOCK_CONTROL_NRF_CALIBRATION_MAX_SKIP > 0. Implementation did
not reflect this dependency correctly, and sensor sampling code was
always compiled. Also removed CONFIG_MULTITHREADING checks, since this
driver is only compiled if CONFIG_MULTITHREADING=y.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
ASSERT was failing when `r8a7795_cpg_mssr_start_stop` was
called for a "core" clock.
This ASSERT statement and "mstpcr" table of registers are
only meant to be used when starting or stopping a "module" clock.
Moved ASSERT statement to `rcar_cpg_mstp_clock_endisable`
as well as "reg" & "bit" calculation.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
STM32h7 pllout frequency calculation overflows. In the
worst case pllsrc_freq can be 50Mhz and plln_mul 512 which will cause
an overflow of the intermediate result which leads to wrong frequency
returned. As no intermediate result can be bigger than 960MHz only the
order of operations is changed.
Signed-off-by: Benjamin Bigler <benjamin.bigler@securiton.ch>
The regulator voltage should be set before the clocks are enabled.
This is especially the case when the MSIS at 48MHz is selected as
SYSCLK.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add the "zephyr/" prefix to various #include statements that are
preventing the CI form running with LEGACY_INCLUDE_PATH=n.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
MSIS frequency at boot time can be different from the one we intent to
set from device tree configuration.
In order to avoid issues, read MSIS configuration from registers to get
the actual freq rather than the devicetree one which may be not yet
configured (which is the case at startup).
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
When configuring PLL, we should first make sure we're not running on PLL,
and if running on PLL, first switch to a fixed clock before proceeding
with PLL configuration.
Current code is doing the switch systematically which is not useful as
default startup case is to use MSI as sysclk source.
So add a test before doing this switch.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Unlike stated in 57df225b396e43358aac4cc998ed2e99fdb57780, RM0456.pdf
reference manual mentions about PLL1R that "Only division by 1 and even
division factors are allowed."
Though, in reference manual, there is one issue on PLL1R values
description, which should actually be:
0000000: pll1_r_ck = vco1_ck
0000001: pll1_r_ck = vco1_ck / 2 (default after reset)
0000010: Not allowed
0000011: pll1_r_ck = vco1_ck / 4
...
This description will be fixed.
Reflect this in binding and driver.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This power down bit of eSPI module is loacted in the bit 7 of PWDWN_CTL6
register rather than the bit 4. This commit fixs the incorrect setting.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
AST10x0 series SOCs provide the clock controller through the syscon
hardware block. The current driver supports the clock gating capability
for the hardware IPs embedded in the SOC. Each clock source has a
clock ID that can simply map to a bit in syscon registers CLK_STOP_CTRL0
(group 0) or CLK_STOP_CTRL1 (group 1). There are some clock sources
that don't have associated clock gating control, which are always on,
are grouped to into group 2.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Some Series were calculating the pll output frequency from an
clock source index instead of the clock source frequency.
This commit resolves this issue for l0, l1.
get_pllout_frequency() is only used for PLLCLK, therefore remove it.
F2, F4, and F7 have several pll dividers and might decide to implement
these as clock sources won't need PLLCLK.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Update clock_control drivers to use DT_HAS_<compat>_ENABLED Kconfig
symbol to expose the driver and enable it by default based on
devicetree.
We remove 'depend on' Kconfig for symbols that would be implied by
the devicetree node existing.
Signed-off-by: Kumar Gala <galak@kernel.org>
The KW40Z/KW41Z don't have a Fixed Freq MCG clock so the code
associated with that in get_rate fails to build. ifdef around
the code with enum kCLOCK_McgFixedFreqClk so things work
correctly.
Signed-off-by: Kumar Gala <galak@kernel.org>
The ESP32 clock control for ESP32C3 was unified into a single
driver a while back. However the files associated with the
ESP32C3 didn't get removed than. Remove them now.
Signed-off-by: Kumar Gala <galak@kernel.org>
This commit adds required code to setup pll2 and pll3 as defined
in dts. Also these plls can now be used as alternate clock sources.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit changes the range for stm32u5 pll divider values
to allow divider value of 1.
- DIVQ is allowed to beconfigured 1 for all PLL instances
- DIVR can be 1 for PLL2 and PLL3, but is not valid for PLl1.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Any project with Kconfig option CONFIG_LEGACY_INCLUDE_PATH set to n
couldn't be built because some files were missing zephyr/ prefix in
includes
Re-run the migrate_includes.py script to fix all legacy include paths
Signed-off-by: Tomislav Milkovic <milkovic@byte-lab.com>
irq_lock() returns an unsigned integer key.
Generated by spatch using semantic patch
scripts/coccinelle/irq_lock.cocci
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Add simple clock control node in devicetree for beetle to handle
relationship between drivers (uart, timers, gpio) and clock controller
device.
Signed-off-by: Kumar Gala <galak@kernel.org>
Some stm32 devices, like stm32F4, do not have
a PLL Enable bit on the PLLP nor PLLQ divider
in their PLL config register (PLLCFGR).
The result is a empty function.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The function get_pllsrc_frequency is added
with possible source HSI or HSE.
With STM32_PLL_P_ENABLED or STM32_PLL_Q_ENABLED,
this function is used by the clock control driver.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Following zephyr's style guideline, all if statements, including single
line statements shall have braces.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
After replacing STM32_SRC_PLLCLK by the STM32_SRC_PLL_x sources
this function is no longer needed and are therefore removed.
Also, those functions returned a wrong frequency.
They should have used get_pllsrc_frequency() instead of get_pll_source()
to get the input frequency.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
The SOC specific implementations of the clock_stm32_ll_common driver
included the PLL specific functions only when PLL was selected as sysclock.
This commit changes the condition from "STM32_SYSCLK_SRC_PLL"
to "defined(STM32_PLL_ENABLED)".
As a result the pll could also be used as peripheral clock source
in case it is not the sysclock.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit adds support to select pll outputs as peripheral clock
sources to the stm32 common driver.
With this commit they are only available on
STM32G0, STM32G4, STM32L4, STM32L5, STM32WB, and STM32WL.
Support for STM32F2, and STM32F4, which also have p,q,r dividers,
is not enabled in this commit.
Also, stm32_clock_control_get_subsys_rate is extended to return
the configured frequency in case they are enabled, otherwise 0.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit configures the PLL_P divider for SOCs compatible to the
stm32_ll_common driver in case a value was defined via a dts property.
Additionally, in case the divider value is defined in the device
tree, the respective pll output is enabled during initialization
in set_up_plls().
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
In the stm32_ll_common driver the PLL_Q divider should not
be directly written to RCC->PLLCFGR->PLLQ, but should be
translated to the matching register value.
i.e. shifting the value to the correct position of the register
is not enough.
This commit makes sure the divider value taken from device tree, is
correctly translated ot the matching register register value by
converting it to a STM32CUBE LL definition LL_RCC_PLLQ_DIV_xx.
Typcial divider to register value mapping:
G0, WB, WL:
Dividers 2-8 mapped to register values 1-7(0 reserved).
G4, L4, L5:
Dividers 2,4,6,8 mapped to reg values 0,1,2,3.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
All these series share the same defines, and while they are not used
by all socs of the common-driver, this is not exptectd to lead to
any conflict.
By moving the defines they can also be used in clock_stm32_ll_common.c
Additionally, the stm32g0 pll_div define was renamed to pllm
in order to match the other series.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
The STM32_SRC_CLOCK_MIN and STM32_SRC_CLOCK_MAX defines
are not really needed because non valid clock sources are already
filtered out by the precompiler.
Only STM32_SRC_CLOCK_MIN was used once in code and can be replaced.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit rewrite renesas R-Car clock driver in order
to be able to support any new SoC easier.
This work is so creating a clock driver per soc alongside a
common driver for all reneasas r-car boars.
- drivers: create a driver per soc
- create a common driver
- create a common header used by soc & common driver
- create a soc specific driver calling for common driver
- dts: use new compatible
- use old yaml as common yaml
- create a new "child" yaml to define the new compatible field
- change compatible in device tree
As in Linux, the driver can support both r8a77951 and r8a77950
SoC's so we decided to name the new driver as in Linux with Zephyr
prefix : "clock_control_r8a7795_cpg_mssr.c".
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
This commit is reworking clock definition in
order to match linux filetree and definition
as much as possible.
- dt-bindings: rework renesas clocks dt-bindings
- regroup renesas related dt-bindings in a folder
- rename renesas rcar common dt-binding to match linux name
- add soc specific dt-binding matching linux name
- soc dt-bindings are defining clocks matching linux names
- dts: use new clocks names
- move clocks definitions in SoC layer for each core clock entry
- driver: use new clocks names
As seen in this commit, we are declaring clocks for "R8A7795" SoC
to match linux names.
Linux is not declaring "R8A77951" SoC specific files because
its also supporting the first H3 SoC version numbered "R8A77950".
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
STM32_DT_CLOCKS was designed to take a device tree node label name as
argument: STM32_DT_CLOCKS(uart1)
Change its implementation to take a node identifier instead:
STM32_DT_CLOCKS(DT_NODELABEL(uart1)).
This make its usage more flexible since the argument can now be extracted
from other DT macros such as DT_PARENT. Then, the following can be done:
STM32_DT_CLOCKS(DT_PARENT(child_node_label)).
Since it is now possible implement STM32_DT_INST_CLOCKS using
STM32_DT_CLOCKS.
Finally, update existing STM32_DT_CLOCKS users and convert
STM32_INST_CLOCK_INFO users to STM32_CLOCK_INFO.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Simple driver that allows one to choose the clock speed of xtensa cores.
It's basically a shim layer on top of SOC level driver.
Also, a really simple test case was added, mainly to ensure things are
build and are sane.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
This commit adds a check for the validity of the "sub_system" param in
clock_control_on.
While for clock_control_off there was a check if the clock_subsytem
parameter is in range of STM32_PERIPH_BUS_MIN and STM32_PERIPH_BUS_MAX
this check was missing for clock_control_on.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
-Kept getting an error on STM32g0xx chips that didn't have q-divisor.
-Changed to set prescaler only if it's being used.
Signed-off-by: Dan Higginbotham <daniel@dedesignworks.com>
<soc.h> has been traditionally been used as a proxy to HAL headers,
register definitions, etc. Nowadays, <soc.h> is anarchy. It serves a
different purpose depending on the SoC. In some cases it includes HALs,
in some others it works as a header sink/proxy (for no good reason), as
a register definition when there's no HAL... To make things worse, it is
being included in code that is, in theory, non-SoC specific.
This patch is part of a series intended to improve the situation by
removing <soc.h> usage when not needed, and by eventually removing it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Adds few missing zephyr/ prefixes to leftover #include statements that
either got added recently or were using double quote format.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Checking that provided pclken->bus fits bus range in
clock_control_get_rate() is wrong as it could actually be a source
clock and hence not belong to this range.
Also, this kind of check is just not needed since this function should
not be used before call to clock_control_on() or clock_control_configure()
which do the required verification.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This PR Fixes the Audio PLL Rate Calculation (there was an additional
divide / 8 which is not necessary and does not appear in similar
calculations in example code from the SDK).
Additionally, it adjusts the SAI .dtsi to more correctly configure the
mclk rate, and adds comments specifying what the regististers mean.
Signed-off-by: Nickolas Lapp <nickolaslapp@gmail.com>
convert lpc11u6x syscon clock driver to pin control, and remove all
pinmux usage from driver and syscon dts node.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Similarly to what was done on U5 and H7 clock_control drivers, enable
device clock source selection.
This is done by:
-providing implementation for clock_control_configure().
-updating clock_control_get_rate() to support various possible clock
sources (SYSCLK, PLLCLK, LSE, LSI, HSI, HSE).
-providing enable_clock() to verify requested clock source exists and
is enabled.
-adding LSI and LSE device tree based initialization to
set_up_fixed_clock_sources().
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rename and factorize clock source bindings accessors by moving them
in common header file stm32_clock_control and remove them from
include/dt-bindings/clock/stm32XY_clock.h files
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use `DT_REG_ADDR_BY_NAME` and `DT_REG_SIZE_BY_NAME` to access register
properties from dts.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
In the EC application, the system may jump between two built Zephyr
images when necessary. If we gate the eSPI clock at initialzation, it
will make the eSPI configuration which established by previous image
break and lost the communication between EC and host.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Implement SDHC driver for NXP USDHC peripheral, supporting all api calls
available in the sdhc driver. This implementation leverages NXP's HAL,
and simply implements a shim layer over the HAL itself.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Changes signature so it takes uint32_t instead of pointer to a
register.
Later `sys_read*` and `sys_write*` functions are used, which cast
given address to volatile pointer anyway.
This required changing types of some fields in LiteX GPIO driver and
removal of two casts in clock control driver.
There was a weird assert from LiteX GPIO driver, which checked whether
size of first register in dts was a multiple of 4.
It didn't make much sense, so I removed it.
Previous dts was describing size of a register in terms of subregisters
used. New one uses size of register, so right now it is almost always
4 bytes.
Most drivers don't read register size from dts anyway, so only changes
had to be made in GPIO and clock control drivers.
Both use `litex_read` and `litex_write` to operate on `n`bytes.
Now GPIO driver calculates this `n` value in compile time from given
number of pins and stores it in `reg_size` field of config struct like
before.
Registe sizes in clock control driver are hardcoded, because they are
tied to LiteX wrapper anyway.
This makes it possible to have code, independent of CSR data width.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
Make the LSE driving capability configurable for the STM32 series.
Fixes#44737.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
STM32H7 series offer alias addresses to access some registers that could
be accessed by the M4 core on dual core variants.
For instance RCC_AHB3ENR could be accessed at following offsets:
- 0x0D4: Accessible from both cores
- 0x134: Accessible from C1 (M7) core
- 0x194: Accessible from C2 (M4) core (if any)
For most single core H7 variants, the two first addresses were accessible,
but for some others (stm32h7ax/stm32h7bx), only the 'C1 accessible'
was available.
This fact used to be hidden by the use of LL API to access these registers,
providing the required abstraction (an mainly using the first alias
when possible to simplify implementation).
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Instead of computing hclk freq use for flash latency setting after
setting the PLLs, do it right at the beginning of the function.
Indeed, first step of PLL configuration is to switch back sysclock
to HSI source (in case it was initially PLL).
In that case, flash latency is theoretically set in consistency with PLL
driver hclk. So we should "measure" hclk freq at that step rather than
once sysclock is back on HSI.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC is the actual hclk freq (ie core clock);
Remove use of intermediate new_hclk_freq to fix and simplify code.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Some specific F1 variants don't handle flash latency.
Put flash latency dealing code under dedicated switch.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Review code style in set_up_fixed_clock_sources() for better
readability.
Use of 'if (IS_ENABLED(STM32_MSI_ENABLED))' inside '#if STM32_MSI_ENABLED'
is redundant but intentional as it is in line with remaining part of the
function (HSE/HSI cases).
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
On some parts, it could be required to use steps before applying
highest frequencies.
This was previously done as part of LL_PLL_ConfigSystemClock_FOO
utility functions which are no more used.
Use device tree to mention when this is required and implement it
in stm32_clock_control_init().
Additionally, fix the calls tp LL_RCC_SetAHBPrescaler, which require
use of ahb_prescaler helper.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Introduce a set_up_pll configuration function and make PLL configuration
an elementary step of the whole system clock configuration.
To implement this new, function make use of the existing series specific
files which allows series specific configuration when required.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Group fixed clocks inits in a unique set_up function.
Each clock is initialized depending on its dts status.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Simplify and clean up driver code using STM32 clocks DT based macros.
Added STM32_FLASH_PRESCALER macro for this purpose.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Factorize setting of frequency for busses.
Additionally, factorize SysCoreClock update.
The operations are now done twice in case of PLL since they are part
of LL utils PLL configuration function, but they are removed in next
commits.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Take advantage of previous work to configure PLL and remove
usage of LL_PLL1_ConfigSystemClock_FOO utils functions.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Now that fixed clocks are enabled in a single function, a
bunch of functions could now be removed.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move fixed clocks initialization to a single function.
Benefit is they could now be enabled independently of the
main clock configuration based on dts status and then be
used by peripherals even is not part of the main clock tree.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Flash latency setting could be factorized in a single location,
rather than split in each clock setting function.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move prescaler settings to the clock_control_init function.
At this step they will be set up twice in PLL case, this will
be fixed in a next step.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Set bus binding values using registers offset values.
As a consequence update driver to take this into account
in clock_on and clock_off functions.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Workaround for errata 192 is unnecessary as it is applied within
nrfx_clock_calibration_start().
Fixes#43930
Signed-off-by: Xudong Zheng <7pkvm5aw@slicealias.com>
Fix register bit field when clock source is MSI
on the stm32L0x or stm32L1x mcus
Use RCC_CR_MSIRGSEL bit field instead of not soc stm32wbx serie
That bit of the RCC CR is common to several stm32 mcus
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The temperature sensor used in the clock_control driver requires
multithreading, but this is not compatible with mcuboot builds with
multithreading disabled.
Fixes#41597.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Shims for nrfx drivers should only connect the related IRQ handlers,
they should not enable the IRQs, as this could lead to a situation
where the interrupt handler is called before the driver had a chance
to properly initialize the peripheral and install the provided event
handler. nrfx drivers will enable the interrupts appropriately on
their own by calling the NRFX_IRQ_ENABLE macro which is implemented
in nrfx_glue.h as a call to irq_enable().
This commit fixes the above issue spotted in the following shims:
- dmic_nrfx_pdm
- clock_control_nrf
- i2s_nrfx
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Instead of reading registers query the info on sysclock configuration
from existing configuration symbols.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rework clock start up functions in order to allow configuration
and enabling of individual clocks.
This way, each clock defined with a "okay" status will be enabled
even if not part of the sysclock clock tree.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add STM32_FOO_ENABLED and STM32_FOO_FREQ to STM32 fixed clocks:
HSI, HSE, MSI(S), CSI, LSI, LSE..
Replace STM32_LSE_CLOCK by STM32_LSE_FREQ and when possible
replace by new STM32_LSE_ENABLED when making sense.
Fix STM32_PLL3_FOO_ENABLE to STM32_PLL3_FOO_ENABLED
Additionally, add STM32_PLL_FOO_ENABLED definitions.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
PLL3 setting should also be protected CFG_HW_RCC_SEMID.
Move semaphore unlock after we're done with PLL3.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32H7B3 supports max SYSCLK and AHB clock frequencies of 280 MHz,
and max APB frequency of 140 MHz
Signed-off-by: Tomislav Milkovic <tomislav.milkovic95@gmail.com>
An optional reference to the temperature sensor can be obtained at
compile time, update implementation.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This commit sets the power down bit of the module SDP, UART3, UART4,
and I3C by default. The module's driver should take the responsibility
to clear it to turn on the power. It helps reduce the power consumption
when an application doesn't use these modules.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
This corrects the following:
1. The priority of type cast is lower than member access. So don't need
the redundant parentheses.
2. The macro should be added to the parentheses.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
Build shows warning due to incompatible
CPU vendor name. This fixes it and applies
necessary changes in files.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
1. Update to add support for Flexcomm8-13.
2. Fix the clock control driver, the enclosing #define
was incorrect.
3. Identify HS_SPI port using the appropriate Register
define
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Stop using redundant DEV_DATA/DEV_CFG macros and use dev->data and
dev->config instead.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Recent changes in this function made the code now compatible
with the use of LL API to perform this configuration.
Use it to simplify the driver.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Voltage scaling computation should be done in multiple cases.
Add a function that takes into account all cases.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32H7 has different power supply modes but now Zephyr supports just LDO
and direct SMPS. This commit introduses POWER_SUPPLY_CHOICE configuration
parameter and add support for missed power supply modes.
Signed-off-by: Gennady Kovalev <gik@bigur.com>
Fixes#40730.
DMA controller is enabled and tested for cortex M7 core. The M7 core was
tested on the loop and channel link transfer tests.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
the RT685 contains an additional flexcomm peripheral, that supports
only I2C. This commit adds this peripheral to the device tree,
and enables pins and clocks for flexcomm15.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
MCUX PWM driver used hardcoded clock source. update driver to use clock
bindings to determine PWM peripheral clock frequency.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
In case of MSIS selected as system clock source it is necessary
to set Voltage scaling (VOS) when freqency is greater than 24MHz
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
When MSI trimming values where set to 0,
and MSIS is used as system core clock and MSI > 4 MHz,
it causes uart to fail.
There is no need to set thoses trimming values.
So keep the default reset value. (keep ST Factory calibration)
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Because on stm32u5 MSIS is the default clock after reset,
changing MSIS range means immediate frequency change.
Thus it is important to do it after flash latency change
in case of higher new frequency.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
This joins all clock control handling to same source
by using hal clock functions. It also brings ESP32C3
clock support.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
This commit is fixing the error on clock control for the AHB3
in the stm32_clock_control_off function.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Refactors all of the clock control drivers to use a shared driver class
initialization priority configuration,
CONFIG_CLOCK_CONTROL_INIT_PRIORITY, to allow configuring clock control
drivers separately from other devices. This is similar to other driver
classes like I2C and SPI.
Most drivers previously used CONFIG_KERNEL_INIT_PRIORITY_OBJECTS or
CONFIG_KERNEL_INIT_PRIORITY_DEVICE, therefore the default for this new
option is the lower of the two, which means earlier initialization.
The even lower defaults for STM32 and Arm Beetle are preserved by
SoC-family level overrides.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
When CLOCK_CONTROL_NRF_FORCE_ALT is enabled then calibration is
performed outside of the driver. In that case certain Kconfig
options where present which were dedicated for case when calibration
is performed by the driver. Side effects of those options lead to
conflicts when CLOCK_CONTROL_NRF_FORCE_ALT was enabled. Fixed
those conflicts by introducing Kconfig option which indicates
whether calibration is performed by the driver or not.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
When existing stop mode 1&2, VCO is set to range 4
and should be set back to range 1 to allow full speed
operations.
Rather than setting VCO at startup, set it inside clock
setting procedure so that it could done
in clock reset procedure when existing stop modes.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This constraint on the AHB prescaler is removed.
The ahb-prescaler is allow from 1-512.
For stm32 common and stm32U5 devices.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
When the MSI clock is selected as source on the stm32wbx device,
the MSI has a range to choose the MSI input frequency.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
On STM32WL, HSE clock can take 2 specific options:
-hse-tcxo
-hse-div2
Enable support for these options.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Enable PWR clock unconditionally for L4, L5 and U5
like it is done on other stm32 series
Fixes#37781
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Instead of putting object files inside libzephyr.a,
simply build a separate static library as most other
driver types are doing this already.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
