Correct the size of the channel_setup_cfg array, as it should contain
entries for all available channels (AD4130_MAX_CHANNELS), not for the
available configuration slots (AD4130_MAX_SETUPS).
Move also checking of the channel index to the very beginning of
adc_ad4130_channel_setup(), to avoid potential writes to .live_cfg
beyond the channel_setup_cfg array.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
- Reset specific configuration bits in
USB1_HS_PHYC->USBPHYC_CR before setting new values.
- Set the Frequency Selection (FSEL) bits to operate
the USB PHY Control Register at 24 MHz for proper communication.
- Enable the OTGPHY1 peripheral clock using LL_AHB5_GRP1_EnableClock.
Signed-off-by: IBEN EL HADJ MESSAOUD Marwa <marwa.ibenelhadjmessaoud-ext@st.com>
Add Set_WP function to set SPI flash WP line to low
Add Get_WP function to obtain status of the SPI flash WP line
Signed-off-by: Benson Huang <benson7633769@gmail.com>
Currently, the Zephyr dt requires address to the direction register
instead of the base GPIO address. usually means base address + 0x10 when
compared with Linux.
To make things more consistent between linux and zephyr, handle the
direction offset in the driver itself. This also lays the foundation for
supporting more than 32 GPIOs per port in the future by introducing
offsets for all the banks.
Signed-off-by: Ayush Singh <ayush@beagleboard.org>
The USART is compatiable with the USART feature in sama7g5's Flexcom.
Update serial/usart_sam to support sama7g5.
Signed-off-by: Tony Han <tony.han@microchip.com>
The FLEXCOM offers several serial communication protocols that are
managed by the three sub-modules USART, SPI, and TWI (I2C).
Signed-off-by: Tony Han <tony.han@microchip.com>
While getting alarm time, BIT(7) of each register is checked if it is
set, which send the alarm time as 0 to the requestor. Fix it by checking
if the BIT(7) of each register is not set.
Signed-off-by: Thiyagarajan Pandiyan <psvthiyagarajan@gmail.com>
update members in struct Netc_Eth_Ip_StationInterfaceConfigType
in RTD 2.0.1 for both psi and vsi driver code.
Netc_Eth_Ip_VsiToPsiMsgType need to relocate nocache section
in RTD 2.0.1
Signed-off-by: Tu Nguyen Van <tu.nguyenvan@nxp.com>
eMios_Icu_Ip_IndexInChState is changed to
eMios_Icu_Ip_u8IndexInChState and EMIOS_ICU_BUS_F
is removed in RTD 2.0.1
Signed-off-by: Tu Nguyen Van <tu.nguyenvan@nxp.com>
Now that api core functions check that denominator / numerator are not
null, it is no more necessary to perform this check within drivers.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Now that video api functions have __ASSERT_NO_MSG calls, drivers
do not need to check the entry point functions pointers.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Protect video API functions via __ASSERT_NO_MSG call to ensure that
required pointers are valid when entering functions.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
The recommended reset sequence from the datasheet is as follows:
void SSD1309 ()
{
RES=0;
delay(1000);
RES=1;
delay(1000);
..
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
This commit adds a driver for the BH1790 Heart Rate Monitor IC.
Based on the approach used by the MAX30101 driver, an existing optical
heart rate sensor with a sample in Zephyr.
Signed-off-by: Magpie Embedded <magpieembedded@gmail.com>
This commit updates the riscv_machine_timer driver to resolve MTIME and
MTIMECMP register addresses by their `reg-names` instead of relying on
index order.
This improves clarity and robustness in DTS bindings, and is a prerequisite
for handling cases where not both MTIME and MTIMECMP registers are present
or accessible.
Signed-off-by: Chen Xingyu <hi@xingrz.me>
`timings` is an array of `struct i2c_config_timing` (3 x `uint32_t`).
`i2c_timings_##index` is an array of `uint32_t` (hence the cast when it
is assigned to `timings`). Therefore `ARRAY_SIZE(i2c_timings_##index)` is
off by a factor 3 when used for `n_timings`.
Parentheses around the second `sizeof` are there to silence the gcc warning
(-Wsizeof-array-div) that warns about not computing the size of
`i2c_timings_##index`.
Signed-off-by: Wouter Horré <wouter@versasense.com>
A -1 was missing from the timer value calculation. In addition,
DIV_ROUND_CLOSEST was replaced with a custom macro fixing #84782.
Signed-off-by: Sergei Ovchinnikov <sergei.ovchinnikov@nordicsemi.no>
Fix issue where STM32 I2C LL driver could block forever when SDA and SCL
are shorted and interrupts are disabled (CONFIG_I2C_STM32_INTERRUPT=n).
Added timeouts to all blocking wait loops in the STM32 LL I2C driver to
avoid indefinite blocking.
Fixes#88506
Signed-off-by: Jean Nanchen <jean.nanchen@hevs.ch>
Migrate renesas,ra-agt-counter implementation to use hal_renesas.
Add additional AGT_CLOCK_SUBCLOCK count source.
Add constraint for counter resolution to 32 or 16 bit variant.
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
Updated set_drp_toggle to handle differences in TCPCI revisions.
Added a macro for TCPCI revision and read it from the chip register
during initialization.
Signed-off-by: Jianxiong Gu <jianxiong.gu@outlook.com>
The ipm_send() allows transferring data through the IPM device.
However, depending on the platform, the mailbox peripheral may either
transmit a limited amount of data or not transfer data at all.
Introducing this configuration allows exposing the IPM capability to the
application.
This commit defines a default value of 1024 bytes to avoid impacting
existing IPM drivers and sets the value to 0 for the STM32 IPCC and
STM32 HSEM devices.
This allows, in a next step, other devices to use this configuration to
expose their capabilities instead of using proprietary configuration or
a static definition.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
- Setting default value of passive scan
dwell time of 400ms as SDK doesn't
configure default value.
Signed-off-by: Nitin Pandey <nitin.pandey@silabs.com>
