The sample uses generate_inc_file_for_target for some "webpages" that
get included. However, the directory that the generated files are
put into: ${ZEPHYR_BINARY_DIR}/include/generated/web_page isn't
created and thus the build fails.
Add a simple 'file(MAKE_DIRECTORY ..)' to create the dir.
Fixes#34345
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove board code and a few associated samples/tests that explicitly
call pinmux_pin_set() to set a given pin as GPIO. This is handled as
part of gpio_mcux_configure() so we don't need to do it again.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace all existing deprecated API with the recommended alternative.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add an overlay-capture.conf file that can be used to allow network
packet capturing in this sample app.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
A simple application that allows you to use net-shell to
configure network packet capturing. The captured packets are
sent to external systems for processing. This can be used
for debugging network protocols.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove legacy TCP stack as it is replaced by the new TCP2 stack.
The TCP2 stack has been the default stack since 2.4 release.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Civetweb does not work properly with mbedtls if Posix APIs
are enabled. For example time function prototypes are not found
by the mbedtls module if we enable mbedtls in the sample.
Disable TCP ISN RFC6528 support because of this for civetweb
samples, as setting that option will pull in mbedtls and
we get a compilation warning because time() is not declared
by any header file that mbedtls is including.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove SPI_[0-8] and SPI_[0-8]_OP_MODES Kconfig symbols as no driver
uses them anymore. We also cleanup board and sample code to remove
use of these symbols.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Currently there is no way to distinguish between a caller
explicitly asking for a semaphore with a limit that
happens to be `UINT_MAX` and a semaphore that just
has a limit "as large as possible".
Add `K_SEM_MAX_LIMIT`, currently defined to `UINT_MAX`, and akin
to `K_FOREVER` versus just passing some very large wait time.
In addition, the `k_sem_*` APIs were type-confused, where
the internal data structure was `uint32_t`, but the APIs took
and returned `unsigned int`. This changes the underlying data
structure to also use `unsigned int`, as changing the APIs
would be a (potentially) breaking change.
These changes are backwards-compatible, but it is strongly suggested
to take a quick scan for `k_sem_init` and `K_SEM_DEFINE` calls with
`UINT_MAX` (or `UINT32_MAX`) and replace them with `K_SEM_MAX_LIMIT`
where appropriate.
Signed-off-by: James Harris <james.harris@intel.com>
We need to set a proper IPv4 netmask to each VLAN interface
so that IPv4 source address selection will work properly.
If we do not do this, then the network interface could be
selected incorrectly for the VLAN interfaces which could then
mean that the packet might get dropped by the target device.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Switch to use DEVICE_DT_GET instead of device_get_binding for pinmux
device. As part of this change drop the "label" property from
the pinmux devicetree node and update the binding and dts files to
reflect that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
socket_can_generic.h makes some assumptions that are not always valid
for various drivers with regards to numbering. To clean this up we
add defines for SOCKET_CAN_NAME_0 and SOCKET_CAN_NAME_2 in addition to
SOCKET_CAN_NAME_1.
We also move struct socket_can_context into the drivers themselves
since they know best how many CAN interfaces are getting supported and
what naming/number convention they'd have.
Additionally, this also exposes a few other build issues with the
can_mcux_flexcan driver that get fixed.
Finally, we remove the platform_allow from samples/net/sockets/can
since it is no longer needed.
Fixes#31733
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch replaces magic numbers with COAP_TOKEN_MAX_LEN value and
removes unnecessary castings of token buffer type.
Signed-off-by: Hubert Miś <hubert.mis@nordicsemi.no>
RFC 7252 (CoAP) specifies value of the Version (Ver) field in the
protocol header to value 1. This patch defines value of the Version
field to make packet initialization easier. All samples and tests
are updated to use the new COAP_VERSION_1 field when initializing
a CoAP packet.
Signed-off-by: Hubert Miś <hubert.mis@nordicsemi.no>
After the latest upmerge, OpenThread requires explicit configuration
of the Master Key. This commit adds a Kconfig symbol that can be
used to setup its value. By default no Master Key is configured and
OpenThread generates a random one.
The Sockets Echo samples are configured with a fixed key with this
commit.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
If CONFIG_LOG_BACKEND_NET_AUTOSTART is disabled, then the syslog
network backend is not started automatically. This option is
enabled by default but it might be that application needs to
start the backend manually if the network is slow to start or
some special routes needs to be set by the application.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This patch introduces COAP_TOKEN_MAX_LEN definition in coap.h file.
This definition replaces magic number across CoAP protocol
implementation and CoAP samples.
Signed-off-by: Hubert Miś <hubert.mis@nordicsemi.no>
Clean up logging menuconfig by grouping configuration into
sections like: mode, processing configuration, backends.
Additionlly, removed LOG_ENABLE_FANCY_OUTPUT_FORMATTING which is no
longer in use.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Due to the routing, the ip_k66f board can only use RTT to export
console. With this change the SHELL is enabled to get access
to network commands (like ping).
To use it with RTT from Segger:
-------------------------------
On HOST (terminal 1):
./JLink_V664/JLinkRTTLogger -Device MK66FN2M0XXX18 -RTTChannel 1 \
-if SWD -Speed 4000 ~/rtt.log
On HOST (terminal 2):
nc localhost 19021
(19021 is the port number for the Segger RTT server)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The 'local-mac-address' nodes are helpful for assessing if the LLDP like
example of DSA switch works correctly.
As those are used only for testing (or when user explicitly needs them),
those are added as DTS overlay to DSA example.
The 'local-mac-address' properties will be visible when one assess the
LLDP response from ip_k66f board (each LAN port has different IP
assigned).
Example output from 'tcpdump -v -i eth0':
-----------------------------------------
Chassis ID TLV (1), length 7
Subtype MAC address (4): 00:00:12:13:00:37 (oui Unknown)
Port ID TLV (2), length 7
Subtype MAC address (3): 00:00:12:13:00:37 (oui Unknown)
Time to Live TLV (3), length 2: TTL 120s
System Name TLV (5), length 13: ip_k66f LAN:3
End TLV (0), length 0
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch brings simple example on per DSA port LLDP filtering based on
MAC address of received packet.
Each lan1, lan2 and lan3 ports handle separately LLDP packets going into
them.
Nonetheless, the K66F ENET handles correctly all other packets types -
to be more specific - ICMP, TCP/IP.
Setup -> ON HOST:
Configure/start the lldpd daemon (debian 10) on host to use
MAC 01:80:c2:00:00:03:
(lldpd -ddd & ) && sleep 2 && \
lldpcli configure lldp agent-type nearest-non-tpmr-bridge
Signed-off-by: Lukasz Majewski <lukma@denx.de>
CoAP protocol defines registry of Content-Format option values.
This patch adds this enumeration to coap header file to make it
available to all applications using CoAP protocol. It modifies
code using CoAP service to use new enumeration.
Signed-off-by: Hubert Miś <hubert.mis@nordicsemi.no>
Introduce retransmission counter to the coap_pending structure. This
allows to simplify the retransmission logic and allows to keep track of
the number of remaining retranmissions.
Additionally, extend the `coap_pending_init()` function with `retries`
parameter, which allows to set the retransmission count individually for
each confirmable transaction.
Fixes#28117
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Since the additional objects are only added for compilation, enable
them in sample.yaml instead, so that they get built by the CI. Remove
them from the actual sample, as they obfuscate the sample purpose and
the objects visible from the server perspective.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
BLE and LwM2M grew in terms of RAM usage so that the sample does not
fit into nRF52832 anymore in the default configuration. This cause
twister to report an error when overflows errors are enabled.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This fixes an incorrect error message log statement for IPv4 vs.
IPv6 in several net samples.
The error message is in a portion of the files dealing with IPv4
bring-up. If the address is invalid, it logs the invalid address;
however, the IPv4 statement incorrectly refers to ipv6_addr. This
PR corrects it to output ipv4_addr as expected.
Signed-off-by: Steve Winslow <steve@swinslow.net>
This commit replaces the 'select SHELL' statement with
'depends on SHELL' in OPENTHREAD_SHELL config option.
This ensures, that shell will not be implicitly enabled
when OpenThread stack is built.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
Reordering of the struct elements to match the Linux format.
The __packed() is not necessary anymore.
std_id and ext_id is merged to id in the frame and filter.
Additionally, the frames are ready for CAN-FD.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
some tests configured with CONFIG_NEWLIB_LIBC=y,
it's better to add a filter filter: TOOLCHAIN_HAS_NEWLIB == 1
in those tests yaml file.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
A dedicated LwM2M execute callback type has been implemented which
supports execute arguments. The lwm2m engine, lwm2m_client sample and
lwm2m objects have been updated accordingly. Also the API change has
been documented, and the lwm2m engine reference has been updated.
Fixes#30551.
Signed-off-by: Maik Vermeulen <maik.vermeulen@innotractor.com>
- Remove SYS_ prefix
- shorten POWER_MANAGEMENT to just PM
- DEVICE_POWER_MANAGEMENT -> PM_DEVICE
and use PM_ as the prefix for all PM related Kconfigs
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use the core k_heap API pervasively within our tree instead of the
z_mem_pool wrapper that provided compatibility with the older mempool
implementation.
Almost all of this is straightforward swapping of one alloc/free call
for another. In a few cases where code was holding onto an old-style
"mem_block" a local compatibility struct with a single field has been
swapped in to keep the invasiveness of the changes down.
Note that not all the relevant changes in this patch have in-tree test
coverage, though I validated that it all builds.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The k_mem_pool allocator is no more, and the z_mem_pool compatibility
API is going away. The internal allocator should be a k_heap always.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Mark all k_mem_pool APIs deprecated for future code. Remaining
internal usage now uses equivalent "z_mem_pool" symbols instead.
Fixes#24358
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The immediate logging option cannot be used with network logging
support CONFIG_LOG_BACKEND_NET as that would cause the generated
rsyslog messages to be malformed. The UDP packets would only have
one byte payloads which is not correct. So make sure that user is
not able to select a configuration with immediate mode and network
logging.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If user has enabled DHCPv4, then allow to use its address instead
of giving error if static address cannot be set. Similar fix for
IPv6, so allow user to manually set an IPv6 address.
Because DHCPv4 has already set the IPv4 address to the network
interface, then zperf might not be able to add the pre-configured
address to it. So instead of returning immediately, try to use the
IP address that is already in the network interface. This way we
avoid this error print.
uart:~$ zperf udp download 5001
Setting IP address 2001:db8::1
Setting destination IP address 2001:db8::2
Cannot set IPv4 address 192.0.2.1
Unable to set IP
Setting destination IP address 192.0.2.2
Cannot set IPv4 address 192.0.2.1
Unable to set IPv4
Binding to 192.0.2.1
Cannot bind IPv4 UDP port 5001 (-2)
In this example, the network interface already had a proper and working
IPv4 address 192.168.0.2 in it.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
