Fix build error due to cmake requiring a separate
overlay for each of this target's SOCs.
Error being fixed:
```
-- Board: sam_v71_xult, qualifiers: samv71q21
CMake Error at cmake/modules/extensions.cmake:2742 (message):
Board sam_v71_xult defines multiple SoCs.
Shortened file name (sam_v71_xult.overlay) not allowed, use
'<board>_<soc>.overlay' naming
```
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This commit removes the const qualifier from TX (source) buffer
of the chan_blen_transfer DMA test to ensure it gets placed in
RAM rather than flash. This ensures the test can pass on hardware
where the DMA controller is unable to access flash.
Fixes#75125.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Boards that use 1024 byte EEPROM buffers need 16-bit address widths
otherwise eeprom_target driver will cause build failure.
Signed-off-by: Tahsin Mutlugun <Tahsin.Mutlugun@analog.com>
Existing tests fail when 16-bit address width is used. Adjust the code
to support 16-bit addresses as well.
Signed-off-by: Tahsin Mutlugun <Tahsin.Mutlugun@analog.com>
The current version of scipts do not consider OOT boards use cases and
the tests with robot now are strict to only one robot file, which is
not realistic for real environment. This address those issues and allow
multiple testsuits at command line and lists at tests entries. It add
another test parameter to allow configure robotframework options.
Fixes: #74563
Signed-off-by: Gerson Fernando Budke <gerson.budke@ossystems.com.br>
Add missing pull-up for RX pin in nrf54h20dk dual uart configuration.
Lack of pull-up was causing test failures.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
RTCs support a variety of combinations of alarm time fields, set
by the alarm time mask. Until now, alarm tests have selected
only the minute and hour fields, as these are always supported,
but some RTCs require setting every supported field when setting
the alarm time, while other RTCs don't support setting every field.
To support all RTCs in the test suite, a configuration has been
added which makes the alarm time mask configurable. Boards can now
define the specific alarm time mask they want to test within
their boards .conf files.
Additionally, the alarm tests have been refactored to not depend
on the time.h library to determine the struct rtc_time times to
set as these are constant, so they are now provided as const
structs instead.
Signed-off-by: Bjarki Arge Andreasen <bjarki@arge-andreasen.me>
nRF54H20 USB device controller cannot be enabled without VBUS, but the
device should not be connected to the host during testing. Add it to
build_only section.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Do not halt control endpoint, control endpoint may not be enabled when
there no host is connected. Yield after buffer is queued to allow the
driver to work.
Tweak pool size and number of buffers to pass the test with high-speed
drivers.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Restore the default CAN bitrates after having tested setting bitrate and
timing. This ensures the arbitration phase bitrate is proportional to the
data phase bitrate, allowing CAN FD transmission tests to complete.
Fixes: #73723
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This nucleo board inherit from the root `h5` dts some special nodes:
- `vbat` on adc1 channel 2
- `vref` on adc1 channel 17
- `die_temp` on adc1 channel 16
The issue is discussed here:
https://github.com/zephyrproject-rtos/zephyr/issues/72914
Signed-off-by: Alex Fabre <alex.fabre@rtone.fr>
Optee driver should handle GET_THREAD_COUNT call. This limitation is
set in Optee-OS during build and limits number of symultanious calls
to optee. Add sym to handle this limitation.
Signed-off-by: Oleksii Moisieiev <oleksii_moisieiev@epam.com>
Capabilities should be set correctly or optee will show error message:
[00:00:00.000,000] <err> optee: OPTEE does not support dynamic shared
memory
Test suite should set optee UID or the following error message should
be displayed:
[00:00:00.000,000] <err> optee: OPTEE API UID mismatch
Signed-off-by: Oleksii Moisieiev <oleksii_moisieiev@epam.com>
During SMC_RPC_FUNC_ALLOC call optee driver puts new shm object to a4
and a5 variables and then expects this object to be in a1 and a2 from
OP-TEE OS. Fixed behaviour so normal_call callback will act the same
way as OP-TEE OS
Signed-off-by: Oleksii Moisieiev <oleksii_moisieiev@epam.com>
This should test OP-TEE driver basic functionality without
communication with real OPTEE OS.
Signed-off-by: Oleksii Moisieiev <oleksii_moisieiev@epam.com>
The board didn't have a proper overlay for the test and failed to build
the test case causing CI failures.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Fix the devicetree bindings to actually be used as the default
configuration, following the example set by various ST sensor devices.
This requires sadly dropping enums and using #defines for various
options as well as repeating many numbers, but presumably is the way to
do it given the precedent set by ST with sensors like the lsm6dso.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Add support for the EK RA8M1 board
This board is using Renesas RA8M1 MCU.
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
`checkpatch.pl` requires that dts sources are indented with tabs,
fix all the spaces that slipped in while checkpatch wasn't watching.
Signed-off-by: Jordan Yates <jordan@embeint.com>
When running this test with multiple counter instances enabled that
support different capabilities, if one of the instances does not
support the test required capabilities, the test will be
immediately skipped not giving the chance to run to the subsequent
instances.
Fix this by marking the test as skipped, only of all counter instances
under test were skipped.
Fixes#74358
Signed-off-by: Manuel Argüelles <marguelles.dev@gmail.com>
This commit adds a missing #ifdef check which prevents building the
'counter_basic_api' test for boards under the following conditions:
* RTC node is defined in device tree (compatible = "st,stm32-rtc")
* RTC node is disabled in device tree (status = "disabled")
* Kconfig "CONFIG_COUNTER_RTC_STM32=n" is specified
This check matches the ones done a few lines above for NXP MCUs.
Without this check, building the test under the conditions listed above
failed with the infamous `undefined reference to '__device_dts_ord_N'`
linker error, because the test attempts to obtain RTC's `struct device`
despite CONFIG_COUNTER_RTC_STM32=n, which ultimately fails because the
RTC driver is not built unless there is an enabled RTC node in DT.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Coverity found this legitimate issue: the datasheet specifies PS_IT
being 2-bits long (1, 2, 4, 8) and this driver assumes more steps are
available. Remove extraneous fields so the Proximity integration
setting fits in the expected 16-bit value.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
Reduce the spi1 clock freq to pass the testcase on the nucleo
_h753zi or nucleo_h743zi boards
Connect D11 & D12 pins on the board to pass the test
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add google_dragonclaw board definition and allow running the
drivers.counter.basic_api.stm32_subsec test on the board.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Add helper function which calculates the required calibration to
1 Hertz from the actual frequency of an RTC. This helper is both
functional and adds to the documentation of the RTC calibration
API.
The rtc.h header now includes zephyr/kernel.h instead of
zephyr/types.h as __ASSERT_NO_MSG is now referenced in the header.
The commit additionally extends the rtc_api_helpers test suite
with a test to validate the conversion function itself.
Signed-off-by: Bjarki Arge Andreasen <bjarki@arge-andreasen.me>
Check for ENOTSUP on alarm callback test if ALARM functionality is
enabled but callbacks are not supported
Signed-off-by: Jakub Topic <jakub.topic@anitra.cz>
These three sensor types are all largely compatible. The SHT21 and
HTU21D can be supported by this driver by sending command 0xE3 instead
of 0xE0 to read the temperature.
Mention the sensor names in bindings and Kconfig to help those looking
for support to find it. There have been at least five PRs attempting to
add SHT21 and/or HTU21D support that did not realize the Si7006 is the
same.
As mentioned in PR #22862, the Sensirion SH21 is the original. The dts
bindings are adjusted (in a backward compatible way!) to make the sht21
the base binding and si7006 is derived from that.
Examples of dts compatibles:
TE Connectivity née Measurement Sepcialties HTU21D:
compatible = "meas,htu21d", "sensirion,sht21";
Sensirion SHT21:
compatible = "sensirion,sht21";
Silicon Labs Si7006
compatible = "silabs,si7006";
Silicon Labs Si7021
compatible = "silabs,si7021", "silabs,si7006";
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
The mspi flash test is intended to test mspi flash device driver
implementation on MSPI bus. The test requires the device to have at
least two sectors of memory with MSPI_FLASH_SECTOR_SIZE as size.
Signed-off-by: Swift Tian <swift.tian@ambiq.com>
Add a MSPI controller API test and run on native_sim board.
The API implementation within mspi_emul.c is the test target.
The stub device emulator is added for convenience to test controllers.
Signed-off-by: Swift Tian <swift.tian@ambiq.com>
Add SENSOR_ATTR_ALERT and SENSOR_ATTR_HYSTERESIS attributes support.
The code is heavily inspired by the one for lm77 sensor.
Signed-off-by: Benjamin Lemouzy <blemouzy@centralp.fr>
Clean up register addresses for devices defined as children of the dummy
SPI bus, so that they start from zero. This ensures all SPI chip select
gpio indices will be used
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Convert galaxycore GC9X01 to MIPI DBI API. In tree boards and tests
using this display have also had their devicetrees updated to use the
new MIPI DBI SPI emulated device.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add a driver for the National/TI LM95234 Quad Remote Diode and Local
Temperature Sensor with SMBus Interface and TruTherm Technology.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
This patch file updates the use of assertion macros
comparing strings.
Command line used:
```
./scripts/coccicheck --mode=patch \
--cocci=scripts/coccinelle/ztest_strcmp.cocci tests/
```
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
