- Defined 'api_configure' function outside of
'CONFIG_UART_USE_RUNTIME_CONFIGURE' macro because it is the only
configuration function and used in device initialization function.
- Removed unnecessary 'IF_ENABLED' part.
Signed-off-by: Furkan Akkiz <hasanfurkan.akkiz@analog.com>
Add support for the EK RA8M1 board
This board is using Renesas RA8M1 MCU.
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
Update rx and tx ready function as per of its description.
For tx_ready if tx interrupt enabled AND tx fifo is not full
For rx_ready if rx interrupt enalbed AND rx fifo not empty
Signed-off-by: Sadik Ozer <sadik.ozer@analog.com>
After enabling interrupts, serial_esp32_usb_irq_tx_enable() calls the
interrupt handler to handle any old events that occurred while interrupts
were disabled. However, this happens in the callers context, so if an
interrupt arrives during the call, it will call the interrupt handler again
resulting in corruption if the interrupt handler is not reentrant.
Fixes#74569
Signed-off-by: Eric Holmberg <eric.holmberg@northriversystems.co.nz>
drivers/serial/uart_async_to_irq.c: In function 'get_rx_timeout':
drivers/serial/uart_async_to_irq.c:51:26:
warning: 'cfg.baudrate' may be used uninitialized
51 | baudrate = cfg.baudrate;
| ~~~~~~~~~^~~~~~~~~~~~~~
drivers/serial/uart_async_to_irq.c:45:28: note: 'cfg' declared here
45 | struct uart_config cfg;
Signed-off-by: Piotr Kosycarz <piotr.kosycarz@nordicsemi.no>
Removed PM device runtime support from drivers in PD_SYS domain.
Update the rest device drivers to call pm_device_runtime_get/put()
functions when CONFIG_PM_DEVICE_RUNTIME is enabled.
Signed-off-by: Ioannis Damigos <ioannis.damigos.uj@renesas.com>
Changes to bring support for esp32c6 SoC.
- clock control
- gpio
- pinctrl
- serial
- timer
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
These headers have been deprecated for > 2 full releases,
let's remove them to keep them out of v3.7.0 LTS.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Simple cosmetic change to convert all the source commands
to rsource so that includes are relative to driver/serial.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The uart-controller devicetree binding declares current-speed and
data-bits properties as optional, but the max32 uart driver failed to
build if they weren't defined. Fix the driver by falling back to
commonly used values for these properties.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Set RTS/CTS flow control pins as NC in cyhal
UART object so cyhal will skip to try initialize
those pins.
Initialization of RTS/CTS is done via
PINCNTRL driver.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
As it is up to a driver implementation if a partial filled buffer is
released, this behavior can be configured during runtime to allow testing
for this edge case.
Signed-off-by: Ruben Völl <ruben.voell@grandcentrix.net>
This structure is bad style and not needed. Instead get the surrounding
`struct uart_emul_data` with `CONTAINER_OF()` directly.
Signed-off-by: Ruben Völl <ruben.voell@grandcentrix.net>
When low power mode is enabled then whenever UARTE is not active,
driver attempts to put the peripheral into the lowest power state
by stopping and disabling UARTE. However, it did not put pins into
sleep state which could lead to increased current consumption.
Adding pins state handling to the low power mode.
Pins are put into sleep state only if CONFIG_PM_DEVICE=y.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Legacy shim takes less flash so it should be a first choice on cores
with less code memory (like RISCV cores on nrf54h20). Adding new
instances support to the legacy shim.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
a change in the dma driver exposed that the dma_slot was incorrectly
set in the uart driver. this change is needed for async uart on lpc55
to work.
Signed-off-by: Johan Carlsson <johan.carlsson@teenage.engineering>
Namespaced the generated headers with `zephyr` to prevent
potential conflict with other headers.
Introduce a temporary Kconfig `LEGACY_GENERATED_INCLUDE_PATH`
that is enabled by default. This allows the developers to
continue the use of the old include paths for the time being
until it is deprecated and eventually removed. The Kconfig will
generate a build-time warning message, similar to the
`CONFIG_TIMER_RANDOM_GENERATOR`.
Updated the includes path of in-tree sources accordingly.
Most of the changes here are scripted, check the PR for more
info.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Updated function parameters from `const struct uart_stm32_config *config`
to `USART_TypeDef *usart`. This change reduces the level of pointer
indirection, which minimizes repeated dereferencing and helps reduce
the overall code size.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
This change reduces the level of pointer indirection, which minimizes
repeated dereferencing and helps reduce the overall code size.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Fix async configure function not being called
when the irq driven api is not used, which
both causes a build warning and would not
work at runtime.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Correct a trivial bug and doxygen documentation error
in which data_bits was missused instead of stop_bits.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Signed-off-by: Mateusz Grzywacz <amateusz.grzywacz@gmail.com>
Default priority set to Main Thread's and Stack-size set to 1KiB. This
should still allow for the System work-queue, considering this
Work-queue could be temporarily blocked on BT TX commands.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
Stop relying on the system workqueue, as the BT TX APIs should
potentially block and now by design this will not work with the
Bluetooth Stack (for good reasons). Now the UART NUS driver has a
dedicated workqueue, which all NUS instances share.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
Adapt the driver to verify if DMA buffers are located in noncacheable
memory when DCache is activated, in order to avoid cache coherency issues.
This is required until manual cache coherency management is implemented.
Signed-off-by: Abderrahmane Jarmouni <abderrahmane.jarmouni-ext@st.com>
Two Kconfig symbols were tied to a board-specific DT nodelabel - namely
the `NRFX_UARTE_CONFIG_RX_CACHE_ENABLED` and `UART_<n>_RX_CACHE_SIZE`
were tied to `shared_ram3x_region` - but this is not necessary.
That DT node is where the UARTE driver RX/TX cache buffers are placed
in the default nRF54H20 DK memory map, but on another board, they could
be located somewhere else.
The exact memory sub-regions used for this purpose are indicated using
the `memory-regions` property on each UARTE instance, which should be
generic enough already, so let's use that instead.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
This change allows to use DTR line driven from external serial port
that when active (low) will prevent UART device from going to sleep.
It will also wake up platform when DTR line becomes active.
DTR line is often activated in serial port connected to host computer
when operating system opens serial device like COMx for Windows
or /dev/ttyACMx /dev/ttyUSBx for Linux based systems.
DTR line (specified in device tree) will be used by WAKEUP and PDC
controllers (via GPIO driver) to handle DTR line changes.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
This change allows to wake up UART from sleep mode when
low level on inactive UART is detected during platform sleep.
Timeout can be specified for each UART separately in device tree.
If one of the UARTs is selected as console sleep timeout is taken
from Kconfig same way other platform configure same functionality
using CONFIG_UART_CONSOLE_INPUT_EXPIRED_TIMEOUT
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
This is initial version that implements device power
management support when configured in Kconfig files.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Apollo3 SoCs have different UART register design compared with
that of Apollo4 SoCs, we need to change the offset and mask for
the power status check
Signed-off-by: Hao Luo <hluo@ambiq.com>
Handle controller instances wanting to use different
API instances, need to change init flow so that they dont
interfere with each other, trick for now is returning
either the interrupt driven or async apis as not enabled
if the other has already been used on that controller.
Previously, there was an issue where enabling CONFIG_UART_ASYNC_API
would overwrite the init even if controller was meant to use
interrupt driven (as kconfig is global to affect all the controllers)
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
This reverts commit a80fa5163b.
That commit broke the polling API when used with the interrupt driven,
it is completely wrong to disable the receiver from irq_rx_disable,
the uart_basic_api test has been broken on all lpuart platforms because
of this bug.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
1. support the baudrate = 3MHz.
2. add baudrate = 115200 setting when UART source clock = 25/30/48/50 MHz.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
This commit implement the UART asynchronous API mode support.
When the API is used, the UART hardware cooperates with the DMA (MDMA)
module to handle the the data transfer and receiving.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
