Check error codes when sending invalid frames:
- too big data payload;
- wrong set of flags.
Signed-off-by: Sebastian Głąb <sebastian.glab@nordicsemi.no>
There is negative test for too high data bitrate.
Add test that checks too low data bitrate.
Signed-off-by: Sebastian Głąb <sebastian.glab@nordicsemi.no>
This commit does the following:
1. tests set_callback and user_data
2. fixes the api as well as the drivers by passing user_data
back to the set callback
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
Add overlay for APARD32690 board and add a new test case to
test RTIO functionalities of SPI MAX32 driver.
Signed-off-by: Dimitrije Lilic <dimitrije.lilic@orioninc.com>
Enable flash driver test for MAX32690 boards.
Signed-off-by: Mert Vatansever <mert.vatansever@analog.com>
Signed-off-by: Sadik Ozer <sadik.ozer@analog.com>
Add wsen_hids_2525020210002 driver with
the corrected name and compatibility with
the hal update as well as added new features.
Signed-off-by: Wajdi ELMuhtadi <wajdi.elmuhtadi@we-online.com>
Add support for Bosch bmp390 sensor, the drop in replacement for the
bmp388 with same register but different chip-id. This patch make use
of "bosch_bmp390" or "bosch_bmp388" and set the specific chip-id in a
data->chip-id variable, which then used to check against the register
value.
Additional, manual shift operation had been replaced with ENDIAN safe
macros and calibration values with target variable of int16_t add a
cast for it.
bmp388_spi: read register implementation wrong, fixed it.
tx-buffer must be <addr><dummy><dummy> in order to receive the
register value. Read registers in burst mode and have rx and tx
buffer same spi_buf to avoid clock stop and delay with nrf5.
Signed-off-by: Chris Ruehl <chris@gtsys.com.hk>
Add test suite which uses GPIO loopback to produce a "very low" and
"very high" voltage at the positive input of the comparator using the
output of a GPIO. The negative input is set to a voltage between the
high and low output voltages of the GPIO using whichever internal
reference is available to the comparator.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
A bunch of copy-paste mistakes when adding the nRF54L15 DK added stale
references to the Preview DK (PDK).
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Some devices may belong to >1 power domain, so with the current design
this is something not possible to describe. It's worth to note that
Linux also uses the `power-domains` naming scheme, not `power-domain`.
This patch also introduces `power-domain-names` so that each entry in
`power-domains` can be given a name if needed. `#power-domain-cells`
is now required as well.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Change integration_platform -> platform_allow to not build the
shell test suite for all supported boards.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
retained_mem driver is now compatible with nrf54h20 cpuapp & cpurad.
Also add missing .conf for nrf54l15.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Enable dma boards/test for S32Z270.
The non-cacheable memory used for DMA tests (chan_blen_transfer and
loop_transfer) is split from the system SRAM.
Signed-off-by: Ha Duong Quang <ha.duongquang@nxp.com>
1. add delay read config for platforms that has capacitor with pin
2. add dts pin flags to gpio_pin_config when output.
Signed-off-by: Hake Huang <hake.huang@nxp.com>
update boards that can not use the common pins
mimxrt102x reuse with ethernet
mimxrt106x has external pull up
lpcxpresso55s3x reuse with int
add CONFIG_SKIP_PULL_TEST by default to be more general
user can enable this test in customized case with select pin
ST prefer to using D9 D10 pair to testing.
Signed-off-by: Hake Huang <hake.huang@nxp.com>
This allows to run the test 'chan_blen_transfer' and 'loop_transfer' on
the sgrm board.
The functionality tested in `chan_link_transfer` and `scatter_gather` is
not (yet) supported by the Si32 DMA driver, and those tests therefore
not enabled.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Use EXTRA_CONF_FILE in sample yaml files,
that replaced deprecated OVERLAY_CONFIG
since the Zephyr v3.4 release.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Adds a Kconfig fragment which changes the MFD init priority
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
This is a follow-up to commit 7a2ce2882a.
Do not enable clock control by default on nRF54H Series SoCs when
the system timer is present, because clock control is not needed
for this purpose there.
Add missing `default y` in the CLOCK_CONTROL_NRF2 Kconfig option that
enables compilation of clock control drivers for nRF54H Series.
This way modules that actually require clock control (like drivers
that use radio) will be able to enable it using the generic option
(CLOCK_CONTROL), not the above one that is specific for nRF54H.
Update accordingly applications that referenced the CLOCK_CONTROL_NRF2
option.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
