peripheral-id property should be eventually removed.
For now set it as optional and allow skipping the usage
in UART driver.
Signed-off-by: Pawel Czarnecki <pczarnecki@antmicro.com>
This commit adds a series of driver-related changes to
Gecko pinctrl.
Co-authored-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Serial speeds listed in device tree did not reflect
what driver supports.
2M and 500K were missing while
1200, 2400 and 460800 were present while not supported.
This change synchronized dts with driver code:
drivers/serial/uart_smartbond.c
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
We are about to add UART reset during driver initialization. First step
is to add 'resets' property, which provides information about reset
register offset and bit.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
NXP LPUART IP supports rs485 mode when transceiver driver enable
using RTS. Allow setting rs485 mode up via the "nxp,rs485-mode"
dts property. "nxp,rs485-de-active-low" dts property can be used
for set RTS polarity.
Signed-off-by: Grixa Yrev <GrixaYrev@yandex.ru>
Add RX and TX fifo size properties to CDC ACM UART bindings.
This allows per instance settings in contrast to Kconfig
USB_CDC_ACM_RINGBUF_SIZE option. New properties takes the default
size value of USB_CDC_ACM_RINGBUF_SIZE which can be removed
subsequently.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
DTS property attributes are (by default) not required.
Explicitly specifying `required: false` is redundant.
Perhaps a warning to that effect would be useful.
Signed-off-by: Chris Friedt <cfriedt@meta.com>
USB interface that may be used to send messages from a USB host to
the M4 processor in the S3B, and vice-versa.
Signed-off-by: Michal Sieron <msieron@antmicro.com>
As part of a previous refactor, this property was removed from the STM32
USART binding. The driver code to support this feature was not changed.
This commit simply adds the property back to the new base .yaml for
device trees which used it.
Tested on a proprietary board using the STM32U5 on USART1.
Signed-off-by: Peter Maxwell Warasila <madmaxwell@soundcomesout.com>
This patch introduces support for NXP S32 LINFlexD peripheral operating
in UART mode. Polling and interrupt-based serial API's are supported.
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Include files should not have compatible properties set. These do not
represent real hardware and should therefore not appear to do so, e.g.
by appearing in the bindings index as if they were a real hardware
peripheral.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
When the EXTI Line nb is not set as interrupt by default
(at reset value), the uart instance cannot waekup the
system from its low power stop mode.
The EXTI line must be specified, like with stm32WL55
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds serial driver for Renesas SmartBond(tm) family. Both polling
and interrupt APIs are supported.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
There are 3 bindings for STM32 serial driver:
st,stm32-uart.yaml
st,stm32-usart.yaml
st,stm32-lpuart.yaml
Add a common st,stm32-uart-base.yaml that would be included by these
3 bindings an would group common properties.
Signed-off-by: TLIG Dhaou <dhaou.tlig-ext@st.com>
various microchip bindings set 'girq-cells' and 'pcr-cells'
sections in the bindings. However the bindings where for the
client nodes and thus do not need to set these.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers on a bus use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
This peripheral combines a hardware-based USB CDC ACM serial interface
and a JTAG interface.
It is present in the ESP32-C3.
Signed-off-by: Martin Jäger <martin@libre.solar>
-pin properties, e.g. tx-pin have been replaced by pinctrl. Mark them as
deprecated since old pin configuration schemes will be deprecated in
Zephyr 3.2.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The driver supported getting register shift from Devicetree, from a
custom definition in SoC headers (fragile) or, it took a default value.
This change simplifies things by making reg-shift property required in
all instances.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This commit aligns UARTE shim to utilize memory-region property from
nordic,nrf-uarte compatible. The memory-region is not required
property that enables user to specify placement of dma buffers
in memory region. It is done by assigning to memory-region property,
phandle to node with zephyr,memory-region and mimo-sram compatible.
When memory-region property is not specified for given
instance, buffer is placed in default RAM region with other data.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in uart driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
NXP LPUART IP supports loopback mode, where TX is internally connected
to RX input. Allow setting loopback mode up via the "nxp,loopback" dts
property.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The pinctrl support made usage of the 'peripheral'
property no longer required.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
This commit has the necessary changes to update the consumers
of pinmux driver(SPI, I2C, UART) and update the board specific
files to use the pinctrl interface.
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
Add a new boolean devicetree property `tx-rx-swap` to the
st,stm32-usart binding, used to control TX/RX swap during
device initialization.
Signed-off-by: Alexander Mihajlovic <a@abxy.se>
This update Atmel sam0 serial drivers to use pinctrl driver and API. It
updates all boards with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
